【转帖】drawingview position

yang686526

drawingview position
i create a new drawing with a template file, i open the new drawing file
and i verified the section view g-g position before update drawing.
after update drawing my view is outside on my drawing
but if i verified the section view g-g position again
the new position equal the old position why ?
marc
boolstat = swapp.replacereferenceddocument(vdest, vsource_part, vdest_part)
set part = swapp.opendoc6(vdest, 3, 0, "", longstatus, longwarnings)
boolstatus = part.extension.selectbyid2("section view g-g", "drawingview", 0, 0, 0, false, 0, nothing, 0)
set swselmgr = part.selectionmanager
set swview = swselmgr.getselectedobject6(1, -1)
old_vpos1(0) = swview.position
debug.print old_vpos1(0)(0)
debug.print old_vpos1(0)(1)
debug.print old_vpos1(0)(2)
part.clearselection2 true
part.graphicsredraw2
boolstatus = part.rebuild(swcurrentsheetdisp)
boolstatus = part.extension.selectbyid2("section view g-g", "drawingview", 0, 0, 0, false, 0, nothing, 0)
set swselmgr = part.selectionmanager
set swview = swselmgr.getselectedobject6(1, -1)
new_vpos1(0) = swview.position
debug.print new_vpos1(0)(0)
debug.print new_vpos1(0)(1)
debug.print new_vpos1(0)(2)
unless the rebuild moves your view position this code does nothing to move the view position so it would have no reason to move.
open test1.slddrw in my test7.zip
run this macro and look de g-g section before rebuild command
boolstatus = part.extension.selectbyid2("section view g-g", "drawingview", 0, 0, 0, false, 0, nothing, 0)
set swselmgr = part.selectionmanager
set swview = swselmgr.getselectedobject6(1, -1)
old_vpos1(0) = swview.position
debug.print old_vpos1(0)(0)
debug.print old_vpos1(0)(1)
debug.print old_vpos1(0)(2)
part.clearselection2 true
part.graphicsredraw2
boolstatus = part.rebuild(swcurrentsheetdisp)
'look g-g section
boolstatus = part.extension.selectbyid2("section view g-g", "drawingview", 0, 0, 0, false, 0, nothing, 0)
set swselmgr = part.selectionmanager
set swview = swselmgr.getselectedobject6(1, -1)
new_vpos1(0) = swview.position
debug.print new_vpos1(0)(0)
debug.print new_vpos1(0)(1)
debug.print new_vpos1(0)(2)
i have ran your code and the rebuild changes nothing the view stays where it is. like i say the code doesn't alter the view position anywhere so that is why it reports the same.
are you saying after rebuild the view position moves visually for you? also, your code would not work as is you would need to modify it like so:
option explicit
dim swapp as sldworks.sldworks
dim part as modeldoc2
dim swselmgr as selectionmgr
dim swview as view
dim old_vpos1 as variant
dim new_vpos1 as variant
dim boolstatus as boolean
sub main()
set swapp = application.sldworks
set part = swapp.activedoc
set swselmgr = part.selectionmanager
boolstatus = part.extension.selectbyid2("section view g-g", "drawingview", 0, 0, 0, false, 0, nothing, 0)
set swview = swselmgr.getselectedobject6(1, -1)
old_vpos1 = swview.position
debug.print old_vpos1(0)
debug.print old_vpos1(1)
part.clearselection2 true
part.graphicsredraw2
part.rebuild (swcurrentsheetdisp)
'look g-g section
boolstatus = part.extension.selectbyid2("section view g-g", "drawingview", 0, 0, 0, false, 0, nothing, 0)
'set swselmgr = part.selectionmanager
set swview = swselmgr.getselectedobject6(1, -1)
new_vpos1 = swview.position
debug.print new_vpos1(0)
debug.print new_vpos1(1)
end sub

edited: 09/26/2008 at 04:44 am by luke malpass
quick