【转帖】asme美国机械工程师标准目录2

huangyhg · 发表于 2009-4-26 14:32:55

目录（五）

ASME SEC VIII D3 ART KD-6 Article KD-6 Design Requirements for Openings, Closures, Heads, Bolting, and Seals
ASME SEC VIII D3 ART KD-7 Article KD-7 Design Requirements for Attachments, Supports, and External Heating and Cooling Jackets
ASME SEC VIII D3 ART KD-8 Article KD-8 Special Design Requirements for Layered Vessels
ASME SEC VIII D3 ART KD-9 Article KD-9 Special Design Requirements for Wire-Wound Vessels and Wire-Wound Frames
ASME SEC VIII D3 ART KD-10 Article KD-10 Special Design Requirements for Interlocking Strip-Wound Vessels
ASME SEC VIII D3 ART KD-11 Article KD-11 Design Requirements for Welded Vessels
ASME SEC VIII D3 ART KD-12 Article KD-12 Experimental Design Verification
ASME SEC VIII D3 ART KF-1 Article KF-1 General Fabrication Requirements
ASME SEC VIII D3 ART KF-2 Article KF-2 Supplemental Welding Fabrication Requirements
ASME SEC VIII D3 ART KF-3 Article KF-3 Fabrication Requirements for Materials with Protective Linings
ASME SEC VIII D3 ART KF-4 Article KF-4 Heat Treatment of Weldments
ASME SEC VIII D3 ART KF-5 Article KF-5 Additional Fabrication Requirements for Autofrettaged Vessels
ASME SEC VIII D3 ART KF-6 Article KF-6 Additional Fabrication Requirements for Quenched and Tempered Steels
ASME SEC VIII D3 ART KF-7 Article KF-7 Supplementary Requirements for Materials with Welding Restrictions
ASME SEC VIII D3 ART KF-8 Article KF-8 Specific Fabrication Requirements for Layered Vessels
ASME SEC VIII D3 ART KF-9 Article KF-9 Special Fabrication Requirements for Wire-Wound Vessels and Frames
ASME SEC VIII D3 ART KF-10 Article KF-10 Special Requirements for Helically Wound Interlocking Strip Vessels
ASME SEC VIII D3 ART KR-1 Article KR-1 General Requirements
ASME SEC VIII D3 ART KR-2 Article KR-2 Requirements for Rupture Disk Devices
ASME SEC VIII D3 ART KR-3 Article KR-3 Requirements for Pressure Relief Valves
ASME SEC VIII D3 ART KR-4 Article KR-4 Marking and Stamping Requirements
ASME SEC VIII D3 ART KR-5 Article KR-5 Certification of Flow Capacity of Pressure Relief Valves
ASME SEC VIII D3 ART KE-1 Article KE-1 Requirements for Examination Procedures and Personnel Qualification
ASME SEC VIII D3 ART KE-2 Article KE-2 Requirements for Examination and Repair of Material
ASME SEC VIII D3 ART KE-3 Article KE-3 Examination of Welds and Acceptance Criteria
ASME SEC VIII D3 ART KE-4 Article KE-4 Final Examination of Vessels
ASME SEC VIII D3 ART KT-1 Article KT-1 Testing Requirements
ASME SEC VIII D3 ART KT-2 Article KT-2 Impact Testing for Welded Vessels
ASME SEC VIII D3 ART KT-3 Article KT-3 Hydrostatic Tests
ASME SEC VIII D3 ART KT-4 Article KT-4 Pressure Test Gages and Transducers
ASME SEC VIII D3 ART KS-1 Article KS-1 Contents and Method of Stamping
ASME SEC VIII D3 ART KS-2 Article KS-2 Obtaining and Using Code Stamps
ASME SEC VIII D3 ART KS-3 Article KS-3 Report Forms and Maintenance of Records
ASME SEC VIII D3 MA APP 1 Appendix 1 - Mandatory Nomenclature
ASME SEC VIII D3 MA APP 2 Appendix 2 - Mandatory Quality Control System
ASME SEC VIII D3 MA APP 3 Appendix 3 - Mandatory Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC VIII D3 MA APP 4 Appendix 4 - Mandatory Acceptance of Testing Laboratories and Authorized Observers for Capacity Certification of Pressure Relief Devices
ASME SEC VIII D3 MA APP 5 Appendix 5 - Mandatory Adhesive Attachment of Nameplates
ASME SEC VIII D3 MA APP 6 Appendix 6 - Mandatory Rounded Indications Charts Acceptance Standard for Radiographically Determined Rounded Indications in Welds
ASME SEC VIII D3 NMA APP A Appendix A - Nonmandatory Guide for Preparing Manufacturer's Data Reports
ASME SEC VIII D3 NMA APP B Appendix B - Nonmandatory Requalification
ASME SEC VIII D3 NMA APP C Appendix C - Nonmandatory Guide to Information Appearing on Certificate of Authorization (See Fig. C-1)
ASME SEC VIII D3 NMA APP D Appendix D - Nonmandatory Fracture Mechanics Calculations
ASME SEC VIII D3 NMA APP E Appendix E - Nonmandatory Construction Details
ASME SEC VIII D3 NMA APP F Appendix F - Nonmandatory Approval of New Materials under the ASME Boiler and Pressure Vessel Code
ASME SEC VIII D3 NMA APP G Appendix G - Nonmandatory Design Rules for Clamp Connections
ASME SEC VIII D3 NMA APP H Appendix H - Nonmandatory Openings and Their Reinforcement
ASME SEC VIII D3 SI SI Units
ASME SEC VIII D3 INDEX Index
ASME SEC IX MA APP E Appendix e - Mandatory Permitted SWPSs
ASME SEC IX A2000 2000 Addenda Summary of Changes
ASME SEC IX A99 1999 Addenda Summary of Changes
ASME SEC IX PT QW ARTICLE V Article V Standard Welding Procedure Specifications (SWPSs)
ASME SEC IX A98 1998 Addenda Summary of Changes
ASME SEC IX INTRODUCTION Introduction
ASME SEC IX PT QW ARTICLE I Article I Welding General Requirements
ASME SEC IX PT QW ARTICLE II Article II Welding Procedure Qualifications
ASME SEC IX PT QW ARTICLE III Article III Welding Performance Qualifications
ASME SEC IX PT QW ARTICLE IV Article IV Welding Data
ASME SEC IX PT QB ARTICLE XI Article XI Brazing General Requirements
ASME SEC IX PT QB ARTICLE XII Article XII Brazing Procedure Qualifications
ASME SEC IX PT QB ARTICLE XIII Article XIII Brazing Performance Qualifications
ASME SEC IX PT QB ARTICLE XIV Article XIV Brazing Data
ASME SEC IX MA APP A Appendix A - Mandatory Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC IX NMA APP B Appendix B - Nonmandatory Welding and Brazing Forms
ASME SEC IX NMA APP D Appendix D - Nonmandatory P-Number Listing
ASME SEC IX SI SI Units
ASME SEC IX INDEX Index
ASME SEC X A2000 2000 Addenda Summary of Changes
ASME SEC X NMA APP AF Appendix AF - Nonmandatory Examples for Design Rules for Class II Vessels
ASME SEC X NMA APP AG Appendix AG - Nonmandatory Guide to Information Appearing on Certificate of Authorization (See Fig. AG-1)
ASME SEC X A99 1999 Addenda Summary of Changes
ASME SEC X MA APP 6 Appendix 6 - Mandatory Sturctural Laminate Visual Acceptance Criteria
ASME SEC X A98 1998 Addenda Summary of Changes
ASME SEC X INTRODUCTION Introduction
ASME SEC X ART RG-1 Article RG-1 Scope and Jurisdiction
ASME SEC X ART RG-2 Article RG-2 Organization
ASME SEC X ART RG-3 Article RG-3 Responsibilities and Duties
ASME SEC X ART RG-4 Article RG-4 Fabrication Methods
ASME SEC X ART RM-1 Article RM-1 General Requirements
ASME SEC X ART RM-2 Article RM-2 Miscellaneous Pressure Parts
ASME SEC X ART RD-1 Article RD-1 General
ASME SEC X ART RD-2 Article RD-2 Shells of Revolution under Internal Pressure
ASME SEC X ART RD-3 Article RD-3 Shells of Revolution under External Pressure
ASME SEC X ART RD-4 Article RD-4 Secondary Bonding
ASME SEC X ART RD-5 Article RD-5 Openings and Their Reinforcement
ASME SEC X ART RD-6 Article RD-6 Nozzles and Other Connections
ASME SEC X ART RD-7 Article RD-7 Bolted Connections
ASME SEC X ART RD-8 Article RD-8 Quick-Actuating Closures (for Class I Vessels Only)
ASME SEC X ART RD-9 Article RD-9 Attachments and Supports
ASME SEC X ART RD-10 Article RD-10 Access and Inspection Openings
ASME SEC X ART RD-11 Article RD-11 Mandatory Design Rules for Class II Vessels
ASME SEC X ART RD-12 Article RD-12 Laminate Stiffness Coefficients
ASME SEC X ART RF-1 Article RF-1 General Requirements
ASME SEC X ART RF-2 Article RF-2 Special Fabrication Requirements for Bag-Molding Process (for Class I Vessels Only)
ASME SEC X ART RF-3 Article RF-3 Special Fabrication Requirements for Centrifugal-Casting Process (for Class I Vessels Only)
ASME SEC X ART RF-4 Article RF-4 Special Fabrication Requirements for Filament-Winding Process (Classes I and II)
ASME SEC X ART RF-5 Article RF-5 Special Fabrication Requirements for Contact-Molding Process (Classes I and II)
ASME SEC X ART RF-6 Article RF-6 Special Fabrication Requirements for Matched Molded Heads (Used for Closures for Centrifugally Cast Vessels - for Class I Vessels Only)
ASME SEC X ART RF-7 Article RF-7 Special Fabrication Requirements for Joining Components
ASME SEC X ART RQ-1 Article RQ-1 Scope
ASME SEC X ART RQ-2 Article RQ-2 Special Requirements for Bag-Molding Procedure Qualification (Class I Vessels)
ASME SEC X ART RQ-3 Article RQ-3 Special Requirements for Centrifugal-Casting Procedure Qualification (Class I Vessels)
ASME SEC X ART RQ-4 Article RQ-4 Special Requirements for Filament-Winding Procedure Qualification (Class I Vessels)
ASME SEC X ART RQ-5 Article RQ-5 Special Requirements for Contact-Molding Procedure Qualification (Class I Vessels)
ASME SEC X ART RQ-6 Article RQ-6 Special Requirements for Class II Vessels
ASME SEC X ART RR-1 Article RR-1 General Requirements
ASME SEC X ART RR-2 Article RR-2 Provisions in Vessels for Installation of Pressure Relief Devices
ASME SEC X ART RT-1 Article RT-1 Testing Requirements
ASME SEC X ART RT-2 Article RT-2 Design and Procedure Qualification Test Requirements for Class I Vessels
ASME SEC X ART RT-3 Article RT-3 Quality Control Test and Examination Requirements for Class I Vessels
ASME SEC X ART RT-4 Article RT-4 Production Test Requirements for Class I Vessels
ASME SEC X ART RT-5 Article RT-5 Hydrostatic Testing Procedures and Equipment for Class I and Class II Vessels
ASME SEC X ART RT-6 Article RT-6 Acceptance Test Procedure for Class II Vessels
ASME SEC X ART RT-7 Article RT-7 Determination of Mechanical Properties of Lamina for Use with Class II Vessels
ASME SEC X ART RI-1 Article RI-1 General
ASME SEC X ART RI-2 Article RI-2 Special Inspection Requirements for Bag Molding (Class I Vessels)
ASME SEC X ART RI-3 Article RI-3 Special Inspection Requirements for Centrifugal Casting (Class I Vessels)
ASME SEC X ART RI-4 Article RI-4 Special Inspection Requirements for Filament Winding
ASME SEC X ART RI-5 Article RI-5 Special Inspection Requirements for Contact Molding
ASME SEC X ART RS-1 Article RS-1 Contents, Methods, and Means of Marking
ASME SEC X ART RS-2 Article RS-2 Use of Code Symbol Stamps
ASME SEC X ART RS-3 Article RS-3 Report Forms
ASME SEC X MA APP 1 Appendix 1 - Mandatory Quality Control System
ASME SEC X MA APP 2 Appendix 2 - Mandatory Capacity Conversions for Safety Valves
ASME SEC X MA APP 3 Appendix 3 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC X MA APP 4 Appendix 4 - Mandatory Glossary of Terms Related to Fiber-Reinforced Plastics
ASME SEC X MA APP 5 Appendix 5 - Mandatory Specific Gravity of Liquid Resins
ASME SEC X NMA APP AA Appendix AA - Nonmandatory Suggested Methods of Preliminary Design for Class I Vessels
ASME SEC X NMA APP AB Appendix AB - Nonmandatory Installation and Operation
ASME SEC X NMA APP AC Appendix AC - Nonmandatory Discontinuity Stresses for Class II Method B Vessels
ASME SEC X NMA APP AD Appendix AD - Nonmandatory Laminate Theory
ASME SEC X NMA APP AE Appendix AE - Nonmandatory Fabrication of Flat Filament-Wound Specimens
ASME SEC X FORMS Forms
ASME SEC X SI SI Units
ASME SEC XI A99 1999 Addenda Summary of Changes
ASME SEC XI A2000 2000 Addenda Summary of Changes
ASME SEC XI A98 1998 Addenda Summary of Changes
ASME SEC XI INTRODUCTION Introduction
ASME SEC XI ORGANIZATION Organization of Section XI
ASME SEC XI SI SI Units
ASME SEC XI D1 ART IWA-1000 Article IWA-1000 Scope and Responsibility
ASME SEC XI D1 ART IWA-2000 Article IWA-2000 Examination and Inspection
ASME SEC XI D1 ART IWA-3000 Article IWA-3000 Standards for Examination Evaluation
ASME SEC XI D1 ART IWA-4000 Article IWA-4000 Repair/Replacement Activities
ASME SEC XI D1 ART IWA-5000 Article IWA-5000 System Pressure Tests
ASME SEC XI D1 ART IWA-6000 Article IWA-6000 Records and Reports
ASME SEC XI D1 ART IWA-9000 Article IWA-9000 Glossary
ASME SEC XI D1 ART IWB-1000 Article IWB-1000 Scope and Responsibility
ASME SEC XI D1 ART IWB-2000 Article IWB-2000 Examination and Inspection
ASME SEC XI D1 ART IWB-3000 Article IWB-3000 Acceptance Standards
ASME SEC XI D1 ART IWB-5000 Article IWB-5000 System Pressure Tests
ASME SEC XI D1 ART IWC-1000 Article IWC-1000 Scope and Responsibility
ASME SEC XI D1 ART IWC-2000 Article IWC-2000 Examination and Inspection
ASME SEC XI D1 ART IWC-3000 Article IWC-3000 Acceptance Standards
ASME SEC XI D1 ART IWC-5000 Article IWC-5000 System Pressure Tests
ASME SEC XI D1 ART IWD-1000 Article IWD-1000 Scope and Responsibility
ASME SEC XI D1 ART IWD-2000 Article IWD-2000 Examination and Inspection
ASME SEC XI D1 ART IWD-3000 Article IWD-3000 Acceptance Standards In the Course of Preparation
ASME SEC XI D1 ART IWD-5000 Article IWD-5000 System Pressure Tests
ASME SEC XI D1 ART IWE-1000 Article IWE-1000 Scope and Responsibility
ASME SEC XI D1 ART IWE-2000 Article IWE-2000 Examination and Inspection
ASME SEC XI D1 ART IWE-3000 Article IWE-3000 Acceptance Standards
ASME SEC XI D1 ART IWE-4000 Article IWE-4000 Repair Procedures DELETED
ASME SEC XI D1 ART IWF-1000 Article IWF-1000 Scope and Responsibility
ASME SEC XI D1 ART IWF-2000 Article IWF-2000 Examination and Inspection
ASME SEC XI D1 ART IWF-3000 Article IWF-3000 Standards for Examination Evaluations
ASME SEC XI D1 ART IWF-5000 Article IWF-5000 Inservice Inspection Requirements for Snubbers
ASME SEC XI D1 ART IWL-1000 Article IWL-1000 Scope and Responsibility
ASME SEC XI D1 ART IWL-2000 Article IWL-2000 Examination and Inspection
ASME SEC XI D1 ART IWL-3000 Article IWL-3000 Acceptance Standards
ASME SEC XI D1 ART IWL-4000 Article IWL-4000 Repair/Replacement Activities
ASME SEC XI D1 ART IWL-5000 Article IWL-5000 System Pressure Tests
ASME SEC XI D1 ART IWP-1000 Article IWP-1000 Requirements DELETED
ASME SEC XI D1 ART IWV-1000 Article IWV-1000 Requirements DELETED
ASME SEC XI D1 MA APP I Appendix I Ultrasonic Examinations
ASME SEC XI D1 MA APP II Appendix II Owner's Report for Inservice Inspections
ASME SEC XI D1 MA APP III Appendix III Ultrasonic Examination of Vessels Not Greater than 2 Inches in Thickness
ASME SEC XI D1 MA APP IV Appendix IV Eddy Current Examination
ASME SEC XI D1 MA APP V Appendix V Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC XI D1 MA APP VI Appendix VI Qualification of Personnel for Visual Examination
ASME SEC XI D1 MA APP VII Appendix VII Qualification of Nondestructive Examination Personnel for Ultrasonic Examination
ASME SEC XI D1 MA APP VIII Appendix VIII Performance Demonstration for Ultrasonic Examination Systems
ASME SEC XI D1 MA APP IX Appendix IX Mechanical Clamping Devices for Class 2 and 3 Piping Pressure Boundary
ASME SEC XI D1 NMA APP A Appendix A Analysis of Flaws
ASME SEC XI D1 NMA APP B Appendix B Forms
ASME SEC XI D1 NMA APP C Appendix C Evaluation of Flaws in Austenitic Piping
ASME SEC XI D1 NMA APP D Appendix D Conditioning of Class 1 and 2 Piping Welds Which Require Examination
ASME SEC XI D1 NMA APP E Appendix E Evaluation of Unanticipated Operating Events
ASME SEC XI D1 NMA APP F Appendix F Preparation of Inspection Plans DELETED
ASME SEC XI D1 NMA APP G Appendix G Fracture Toughness Criteria for Protection Against Failure
ASME SEC XI D1 NMA APP H Appendix H Evaluation of Flaws in Ferritic Piping
ASME SEC XI D1 NMA APP J Appendix J Guide to Plant Maintenance Activities and Section XI Repair/Replacement Activities
ASME SEC XI D1 NMA APP K Appendix K Assessment of Reactor Vessels with Low Upper Shelf Charpy Impact Energy Levels
ASME SEC XI D1 NMA APP L Appendix L Operating Plant Fatigue Assessment
ASME SEC XI D1 NMA APP M Appendix M Applying Mathematical Modeling to Ultrasonic Examination of Pressure Retaining Components
ASME SEC XI D2 Division 2 Rules for Inspection and Testing of Components of Gas-Cooled Plants
ASME SEC XI D3 Division 3 Rules for Inspection and Testing of Components of Liquid-Metal Cooled Plants
ASME SEC XI D3 ART IMA-1000 Article IMA-1000 Scope and Responsibility
ASME SEC XI D3 ART IMA-2000 Article IMA-2000 Examination and Inspection
ASME SEC XI D3 ART IMA-3000 Article IMA-3000 Standards for Examination Evaluation
ASME SEC XI D3 ART IMA-4000 Article IMA-4000 Repair and Replacement
ASME SEC XI D3 ART IMA-5000 Article IMA-5000 System Leakage Tests and Monitoring
ASME SEC XI D3 ART IMA-6000 Article IMA-6000 Records and Reports
ASME SEC XI D3 ART IMA-7000 Article IMA-7000 Replacements
ASME SEC XI D3 ART IMA-9000 Article IMA-9000 Glossary
ASME SEC XI D3 ART IMB-1000 Article IMB-1000 Scope and Responsibility
ASME SEC XI D3 ART IMB-2000 Article IMB-2000 Examination and Inspection
ASME SEC XI D3 ART IMB-3000 Article IMB-3000 Acceptance Standards for Examinations
ASME SEC XI D3 ART IMB-4000 Article IMB-4000 Repair Procedures
ASME SEC XI D3 ART IMB-5000 Article IMB-5000 Systems Leakage Monitoring
ASME SEC XI D3 ART IMB-7000 Article IMB-7000 Replacements
ASME SEC XI D3 ART IMC-1000 Article IMC-1000 Scope and Responsibility
ASME SEC XI D3 ART IMC-2000 Article IMC-2000 Examination and Inspection
ASME SEC XI D3 ART IMC-3000 Article IMC-3000 Acceptance Standards In the Course of Preparation
ASME SEC XI D3 ART IMC-4000 Article IMC-4000 Repair Procedures
ASME SEC XI D3 ART IMC-5000 Article IMC-5000 System Leakage Monitoring
ASME SEC XI D3 ART IMC-7000 Article IMC-7000 Replacements
ASME SEC XI D3 ART IMD-1000 Article IMD-1000 Scope and Responsibility
ASME SEC XI D3 ART IMD-2000 Article IMD-2000 Examination Requirements
ASME SEC XI D3 ART IMD-3000 Article IMD-3000 Acceptance Standards In the Course of Preparation
ASME SEC XI D3 ART IMD-5000 Article IMD-5000 System Leakage Monitoring
ASME SEC XI D3 ART IMD-7000 Article IMD-7000 Replacements
ASME SEC XI D3 ART IME-1000 Article IME-1000 Scope and Responsibility
ASME SEC XI D3 ART IME-2000 Article IME-2000 Examination and Inspection
ASME SEC XI D3 ART IME-3000 Article IME-3000 Acceptance Standards
ASME SEC XI D3 ART IME-4000 Article IME-4000 Repair Procedures
ASME SEC XI D3 ART IME-5000 Article IME-5000 System Pressure Tests
ASME SEC XI D3 ART IME-7000 Article IME-7000 Replacements
ASME SEC XI D3 ART IMF-1000 Article IMF-1000 Scope and Responsibility
ASME SEC XI D3 ART IMF-2000 Article IMF-2000 Examination and Inspection
ASME SEC XI D3 ART IMF-3000 Article IMF-3000 Standards for Examination Evaluations
ASME SEC XI D3 ART IMF-4000 Article IMF-4000 Repair Procedures
ASME SEC XI D3 ART IMF-5000 Article IMF-5000 Inservice Test Requirements
ASME SEC XI D3 ART IMF-7000 Article IMF-7000 Replacements
ASME SEC XI D3 ART IMV-1000 Article IMV-1000 Scope and Responsibility
ASME SEC XI D3 ART IMV-2000 Article IMV-2000 Categories of Valves
ASME SEC XI D3 ART IMV-3000 Article IMV-3000 Test Requirements
ASME SEC XI D3 MA APP I Appendix I Calibration of Leak Detectors
ASME SEC XI D3 MA APP II Appendix II Owner's Reports for Inservice Inspections
ASME SEC XI D3 MA APP III Appendix III Ultrasonic Examination of Class 1 and 2 Ferritic Steel Piping Systems
ASME SEC XI D3 MA APP IV Appendix IV Volumetric Examination of Steam Generator Tubing In the Course of Preparation
ASME SEC XI D3 MA APP V Appendix V Under Sodium Scanning In the Course of Preparation
ASME SEC XI D3 MA APP VI Appendix VI Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC XI D3 MA APP VII Appendix VII Qualification of Nondestructive Examination Personnel for Ultrasonic Examination
ASME SEC XI D3 NMA APP A Appendix A Analysis of Flaw Indications In the Course of Preparation
ASME CC B1 BPVC 1998 Code Cases: Boilers and Pressure Vessels Interfiled; Supplement 1: 1998; Supplement 2: 1998; Supplement 3: 1999; Supplement 4: 1999 (Boiler and Pressure Vessel Codes)
ASME CC N1 BPVC 1998 Code Cases Nuclear Components Interfiled; Supplement 1: 1998; Supplement 2: 1998; Supplement 3: 1999; Supplement 4: 1999 (Boiler and Pressure Vessel Codes)
ASME 3977-1 Gas Turbines: Procurement Part 1: General Introdustion and Definitions ISO 3977-1:1997
ASME 3977-2 Gas Turbines: Procurement Part 2: Standard Reference Conditions and Ratings ISO 3977-2: 1997
ASME AS-11 Personnel of Codes, Standards, and Related Conformity Assessment Committees
ASME B15.1 INTERPRETATION Interpretations to B15.1-2000 Safety Standard for Mechanical Power Transmission Apparatus
ASME B18.2.2 Square and Hex Nuts (Inch Series) R(1999)
ASME B18.2.3.8M Metric Hex Lag Screws R(1999)
ASME B18.2.3.8M
ASME B18.18.1M Inspection and Quality Assurance for General Purpose Fasteners R(1999)
ASME B18.18.2M Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners R(1999)
ASME B18.18.3M Inspection and Quality Assurance for Special Purpose Fasteners R(1999)
ASME B18.18.4M Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications R(1999)
ASME B18.22M Metric Plain Washers R(2000)
ASME B27.6 General Purpose Uniform Cross Section Spiral Retaining Rings R(1999)
ASME B27.7 General Purpose Tapered and Reduced Cross Section Retaining Rings R(1999)
ASME B30.19 Cableways
ASME B31.1B Addenda to B31.1-1998 Edition Power Piping
ASME B56.5 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles R(2000)
ASME B56.8 Safety Standard for Personnel and Burden Carriers R(2000)
ASME B56.9 Safety Standard for Operator Controlled Industrial Tow Tractors R(2000)
ASME CC B1 BPVC 1998 Code Cases: Boilers and Pressure Vessels Interfiled; Supplement 1: 1998; Supplement 2: 1998; Supplement 3: 1999; Supplement 4: 1999 (Boiler and Pressure Vessel Codes)
ASME CC N1 BPVC 1998 Code Cases Nuclear Components Interfiled; Supplement 1: 1998; Supplement 2: 1998; Supplement 3: 1999; Supplement 4: 1999 (Boiler and Pressure Vessel Codes)
ASME 3977-1 Gas Turbines: Procurement Part 1: General Introdustion and Definitions ISO 3977-1:1997
ASME 3977-2 Gas Turbines: Procurement Part 2: Standard Reference Conditions and Ratings ISO 3977-2: 1997
ASME AS-11 Personnel of Codes, Standards, and Related Conformity Assessment Committees
ASME B15.1 INTERPRETATION Interpretations to B15.1-2000 Safety Standard for Mechanical Power Transmission Apparatus
ASME B18.2.2 Square and Hex Nuts (Inch Series) R(1999)
ASME B18.2.3.8M Metric Hex Lag Screws R(1999)
ASME B18.2.3.8M
ASME B18.18.1M Inspection and Quality Assurance for General Purpose Fasteners R(1999)
ASME B18.18.2M Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners R(1999)
ASME B18.18.3M Inspection and Quality Assurance for Special Purpose Fasteners R(1999)
ASME B18.18.4M Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications R(1999)
ASME B18.22M Metric Plain Washers R(2000)
ASME B27.6 General Purpose Uniform Cross Section Spiral Retaining Rings R(1999)
ASME B27.7 General Purpose Tapered and Reduced Cross Section Retaining Rings R(1999)
ASME B30.19 Cableways
ASME B31.1B Addenda to B31.1-1998 Edition Power Piping
ASME B56.5 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles R(2000)
ASME B56.8 Safety Standard for Personnel and Burden Carriers R(2000)
ASME B56.9 Safety Standard for Operator Controlled Industrial Tow Tractors R(2000)
ASME B56.11.1 Double Race or Bi-Level Swivel and Rigid Industrial Casters Special Notice - October 1993 R(2000)
ASME B56.11.3 Load Handling Symbols for Powered Industrial Trucks Special Notice - October 1993 R(2000)
ASME B56.11.5 Measurements of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks Special Notice - October 1993 R(2000)
ASME B56.11.6 Evaluation of Visibility from Powered Industrial Trucks R(2000)
ASME B107.58M Riveting, Scaling, and Tinner's Setting Hammers: Safety Requirements
ASME B107.58M
ASME OM-S/G Standards and Guides for Operation and Maintenance of Nuclear Power Plants
ASME BPV DECEMBER-2000 Companies Holding Boiler and Pressure Vessel Certificates of Authorization for Use of Code Symbol Stamps and Testing Laboratories Holding Certificates of Acceptance for Conducting Tests of Pressure Relief Devices No.62-December 2000
ASME BPV APRIL-2001
ASME PTC 12.1 Closed Feedwater Heaters
ASME PTC 12.1
ASME SEC XI D1 ART IWE-5000 Article IWE-5000 System Pressure Tests
ASME SEC XI D1 ART IWE-7000 Article IWE-7000 Replacements DELETED
ASME CC B1 BPVC 1998 Code Cases: Boilers and Pressure Vessels Interfiled; Supplement 1: 1998; Supplement 2: 1998; Supplement 3: 1999; Supplement 4: 1999 (Boiler and Pressure Vessel Codes)
ASME CC N1 BPVC 1998 Code Cases Nuclear Components Interfiled; Supplement 1: 1998; Supplement 2: 1998; Supplement 3: 1999; Supplement 4: 1999 (Boiler and Pressure Vessel Codes)
ASME 3977-1 Gas Turbines: Procurement Part 1: General Introdustion and Definitions ISO 3977-1:1997
ASME 3977-2 Gas Turbines: Procurement Part 2: Standard Reference Conditions and Ratings ISO 3977-2: 1997
ASME AS-11 Personnel of Codes, Standards, and Related Conformity Assessment Committees
ASME B15.1 INTERPRETATION Interpretations to B15.1-2000 Safety Standard for Mechanical Power Transmission Apparatus
ASME B18.2.2 Square and Hex Nuts (Inch Series) R(1999)
ASME B18.2.3.8M Metric Hex Lag Screws R(1999)
ASME B18.2.3.8M
ASME B18.18.1M Inspection and Quality Assurance for General Purpose Fasteners R(1999)
ASME B18.18.2M Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners R(1999)
ASME B18.18.3M Inspection and Quality Assurance for Special Purpose Fasteners R(1999)
ASME B18.18.4M Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications R(1999)
ASME B18.22M Metric Plain Washers R(2000)
ASME B27.6 General Purpose Uniform Cross Section Spiral Retaining Rings R(1999)
ASME B27.7 General Purpose Tapered and Reduced Cross Section Retaining Rings R(1999)
ASME B30.19 Cableways
ASME B31.1B Addenda to B31.1-1998 Edition Power Piping
ASME B56.5 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles R(2000)
ASME B56.8 Safety Standard for Personnel and Burden Carriers R(2000)
ASME B56.9 Safety Standard for Operator Controlled Industrial Tow Tractors R(2000)
ASME B56.11.1 Double Race or Bi-Level Swivel and Rigid Industrial Casters Special Notice - October 1993 R(2000)
ASME B56.11.3 Load Handling Symbols for Powered Industrial Trucks Special Notice - October 1993 R(2000)
ASME B56.11.5 Measurements of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks Special Notice - October 1993 R(2000)
ASME B56.11.6 Evaluation of Visibility from Powered Industrial Trucks R(2000)
ASME B107.58M Riveting, Scaling, and Tinner's Setting Hammers: Safety Requirements
ASME B107.58M
ASME OM-S/G Standards and Guides for Operation and Maintenance of Nuclear Power Plants
ASME BPV DECEMBER-2000 Companies Holding Boiler and Pressure Vessel Certificates of Authorization for Use of Code Symbol Stamps and Testing Laboratories Holding Certificates of Acceptance for Conducting Tests of Pressure Relief Devices No.62-December 2000
ASME BPV APRIL-2001
ASME PTC 12.1 Closed Feedwater Heaters
ASME PTC 12.1
ASME SEC XI D1 ART IWE-5000 Article IWE-5000 System Pressure Tests
ASME SEC XI D1 ART IWE-7000 Article IWE-7000 Replacements DELETED

huangyhg · 发表于 2009-4-26 14:33:41

目录（四）

ASME SEC II B SB-649 SB-649 Specification for Ni-Fe-Cr-Mo-Cu Low-Carbon Alloy (UNS N08904) and Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925, UNS N08031, and UNS N08926) Bar and Wire ASTM B 649-93
ASME SEC II B SB-658 SB-658 Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe ASTM B 658-92
ASME SEC II B SB-668 SB-668 Specification for UNS N08028 Seamless Tubes ASTM B 668-84
ASME SEC II B SB-672 SB-672 Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Bar and Wire ASTM B 672-95
ASME SEC II B SB-673 SB-673 Specification for UNS N08904, UNS N08925, and N08926 Welded Pipe ASTM B 673-91
ASME SEC II B SB-674 SB-674 Specification for UNS N08904, UNS N08925, and UNS N08926 Welded Tube ASTM B 674-91
ASME SEC II B SB-675 SB-675 Specification for UNS N08366 and UNS N08367 Welded Pipe ASTM B 675-90a
ASME SEC II B SB-676 SB-676 Specification for UNS N08366 and UNS N08367 Welded Tube ASTM B 676-90
ASME SEC II B SB-677 SB-677 Specification for UNS N08904, and UNS N08925, and UNS N08926 Seamless Pipe and Tube ASTM B 677-91
ASME SEC II B SB-688 SB-688 Specification for Chromium-Nickel-Molybdenum-Iron (UNS N08366 and UNS N08367) Plate, Sheet, and Strip ASTM B 688-95
ASME SEC II B SB-690 SB-690 Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube ASTM B 690-93
ASME SEC II B SB-691 SB-691 Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Rod, Bar, and Wire ASTM B 691-95
ASME SEC II B SB-704 SB-704 Specification for Welded UNS N06625 and UNS N08825 Alloy Tubes ASTM B 704-91
ASME SEC II B SB-705 SB-705 Specification for Nickel-Alloy (UNS N06625 and N08825) Welded Pipe ASTM B 705-94
ASME SEC II B SB-709 SB-709 Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028) Plate, Sheet, and Strip ASTM B 709-93
ASME SEC II B SB-710 SB-710 Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe ASTM B 710-94
ASME SEC II B SB-729 SB-729 Specification for Seamless UNS N08020, UNS N08026, and UNS N08024 Nickel-Alloy Pipe and Tube ASTM B 729-95
ASME SEC II B SB-751 SB-751 Specification for General Requirements for Nickel and Nickel-Alloy Seamless and Welded Tube ASTM B 751-90
ASME SEC II B SB-775 SB-775 Specification for General Requirements for Nickel and Nickel-Alloy Seamless and Welded Pipe ASTM B 775-90
ASME SEC II B SB-804 SB-804 Specification for UNS N08367 and UNS N08926 Welded Pipe ASTM B 804-93
ASME SEC II B SB-824 SB-824 Specification for General Requirements for Copper Alloy Castings ASTM B 824-93a
ASME SEC II B SB-829 SB-829 Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube ASTM B 829-92
ASME SEC II B SB-858M SB-858M Specification for Test Method for Determination of Susceptibility to Stress Corrosion Cracking in Copper Alloys Using an Ammonia Vapor Test ASTM B858M-95
ASME SEC II C A2000 2000 Addenda Summary of Changes
ASME SEC II C A99 1999 Addenda Summary of Changes
ASME SEC II C A98 1998 Addenda Summary of Changes
ASME SEC II C INTRODUCTION Introduction
ASME SEC II C MA APP I Appendix I - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC II C SI SI Units
ASME SEC II C SFA-5.1 SFA-5.1 Specification for Carbon Steel Electrodes for Shielded Metal Arc Welding AWS A5.1-91
ASME SEC II C SFA-5.2 SFA-5.2 Specification for Carbon and Low Alloy Steel Rods for Oxyfuel Gas Welding AWS A5.2-92
ASME SEC II C SFA-5.3 SFA-5.3 Specification for Aluminum and Aluminum-Alloy Electrodes for Shielded Metal Arc Welding AWS A5.3/A5.3M-99
ASME SEC II C SFA-5.4 SFA-5.4 Specification for Stainless Steel Electrodes for Shielded Metal Arc Welding AWS A5.4-92
ASME SEC II C SFA-5.5 SFA-5.5 Specification for Low-Alloy Steel Electrodes for Shielded Metal Arc Welding AWS A5.5-96
ASME SEC II C SFA-5.6 SFA-5.6 Specification for Covered Copper and Copper Alloy Arc Welding Electrodes AWS A5.6-84R
ASME SEC II C SFA-5.7 SFA-5.7 Specification for Copper and Copper Alloy Bare Welding Rods and Electrodes AWS A5.7-84R
ASME SEC II C SFA-5.8 SFA-5.8 Specification for Filler Metals for Brazing and Braze Welding AWS A5.8-92
ASME SEC II C SFA-5.9 SFA-5.9 Specification for Bare Stainless Steel Welding Electrodes and Rods AWS A5.9-93
ASME SEC II C SFA-5.10 SFA-5.10 Specification for Bare Aluminum and Aluminum Alloy Welding Electrodes and Rods AWS A5.10-92
ASME SEC II C SFA-5.11 SFA-5.11 Specification for Nickel and Nickel-Alloy Welding Electrodes for Shielded Metal Arc Welding AWS A5.11/A5.11M-97
ASME SEC II C SFA-5.12 SFA-5.12 Specification for Tungsten and Tungsten-Alloy Electrodes for Arc Welding and Cutting AWS A5.12/A5.12M-98
ASME SEC II C SFA-5.13 SFA-5.13 Specification for Solid Surfacing Welding Rods and Electrodes AWS A5.13-80
ASME SEC II C SFA-5.14 SFA-5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods AWS A5.14/A5.14M-97
ASME SEC II C SFA-5.15 SFA-5.15 Specification for Welding Electrodes and Rods for Cast Iron AWS A5.15-90
ASME SEC II C SFA-5.16 SFA-5.16 Specification for Titanium and Titanium Alloy Welding Electrodes and Rods AWS A5.16-90
ASME SEC II C SFA-5.17 SFA-5.17 Specification for Carbon Steel Electrodes and Fluxes for Submerged Arc Welding AWS A5.17/A5.17M-97
ASME SEC II C SFA-5.18 SFA-5.18 Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding AWS A5.18-93
ASME SEC II C SFA-5.20 SFA-5.20 Specification for Carbon Steel Electrodes for Flux Cored Arc Welding AWS A5.20-95
ASME SEC II C SFA-5.21 SFA-5.21 Specification for Composite Surfacing Welding Rods and Electrodes AWS A5.21-80
ASME SEC II C SFA-5.22 SFA-5.22 Specification for Stainless Steel Electrodes for Flux Cored Arc Welding and Stainless Steel Flux Cored Rods for Gas Tungsten Arc Welding AWS A5.22-95
ASME SEC II C SFA-5.23 SFA-5.23 Specification for Low-Alloy Steel Electrodes and Fluxes for Submerged Arc Welding AWS A5.23/A523M-97
ASME SEC II C SFA-5.24 SFA-5.24 Specification for Zirconium and Zirconium Alloy Welding Electrodes and Rods AWS A5.24-90
ASME SEC II C SFA-5.25 SFA-5.25 Specification for Carbon and Low-Alloy Steel Electrodes and Fluxes for Electroslag Welding AWS A5.25/A5.25M-97
ASME SEC II C SFA-5.26 SFA-5.26 Specification for Carbon and Low-Alloy Steel Electrodes for Electrogas Welding AWS A5.26/A5.26M-97
ASME SEC II C SFA-5.28 SFA-5.28 Specification for Low-Alloy Steel Electrodes and Rods for Gas Shielded Arc Welding AWS A5.28-96
ASME SEC II C SFA-5.29 SFA-5.29 Specification for Low-Alloy Steel Electrodes for Flux Cored Arc Welding AWS A5.29-98
ASME SEC II C SFA-5.30 SFA-5.30 Specification for Consumable Inserts AWS A5.30-79R
ASME SEC II C SFA-5.31 SFA-5.31 Specification for Fluxes for Brazing and Braze Welding AWS A5.31-92
ASME SEC II C SFA-5.01 SFA-5.01 Filler Metal Procurement Guidelines AWS A5.01-92
ASME SEC II D A2000 2000 Addenda Summary of Changes
ASME SEC II D A99 1999 Addenda Summary of Changes
ASME SEC II D A98 1998 Addenda Summary of Changes
ASME SEC II D INTRODUCTION Introduction
ASME SEC II D SB PT 1 Subpart 1 Stress Tables
ASME SEC II D SB PT 2 Subpart 2 Physical Properties Tables
ASME SEC II D SB PT 3 Subpart 3 Charts and Tables for Determining Shell Thickness of Components under External Pressure
ASME SEC II D APPENDIX 1 Appendix 1 Basis for Establishing Stress Values in Tables 1A and 1B
ASME SEC II D APPENDIX 2 Appendix 2 Basis for Establishing Design Stress Intensity Values for Tables 2A, 2B, 3, and 4
ASME SEC II D APPENDIX 3 Appendix 3 Basis for Establishing External Pressure Charts
ASME SEC II D APPENDIX 4 Appendix 4 Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC II D APPENDIX 5 Appendix 5 Guideline on the Approval of New Materials under the ASME Boiler and Pressure Vessel Code
ASME SEC II D APPENDIX 6 Appendix 6 Metallurgical Phenomena
ASME SEC II D APPENDIX 7 Appendix 7 Guidelines on Multiple Marking of Materials
ASME SEC II D SI UNITS SI Units
ASME SEC III NCA A99 1999 Addenda Summary of Changes
ASME SEC III NCA A2000 2000 Addenda Summary of Changes
ASME SEC III NCA A98 1998 Addenda Summary of Changes
ASME SEC III NCA INTRODUCTION Introduction
ASME SEC III NCA ORGN Organization of Section III
ASME SEC III NCA ACI The American Concrete Institute
ASME SEC III NCA-1000 Article NCA-1000 Scope of Section III
ASME SEC III NCA-2000 Article NCA-2000 Classification of Components and Supports
ASME SEC III NCA-3000 Article NCA-3000 Responsibilities and Duties
ASME SEC III NCA-4000 Article NCA-4000 Quality Assurance
ASME SEC III NCA-5000 Article NCA-5000 Authorized Inspection
ASME SEC III NCA-8000 Article NCA-8000 Certificates, Nameplates, Code Symbol Stamping, and Data Reports
ASME SEC III NCA-9000 Article NCA-9000 Glossary
ASME SEC III NCA SI UNITS SI Units
ASME SEC III D1 NH A2000 2000 Addenda Summary of Changes
ASME SEC III D1 NB A2000 2000 Addenda Summary of Changes
ASME SEC III D1 NE A2000 2000 Addenda Summary of Changes
ASME SEC III D1 NG A2000 2000 Addenda Summary of Changes
ASME SEC III D1 ND A2000 2000 Addenda Summary of Changes
ASME SEC III D1 NF A2000 2000 Addenda Summary of Changes
ASME SEC III D1 NC A2000 2000 Addenda Summary of Changes
ASME SEC III D1 APP A2000 2000 Addenda Summary of Changes
ASME SEC III D1 NB A99 1999 Addenda Summary of Changes
ASME SEC III D1 NB A98 1998 Addenda Summary of Changes
ASME SEC III D1 NB INTRO Introduction
ASME SEC III D1 NB-1000 Article NB-1000 Introduction
ASME SEC III D1 NB-2000 Article NB-2000 Material
ASME SEC III D1 NB-3000 Article NB-3000 Design
ASME SEC III D1 NB-4000 Article NB-4000 Fabrication and Installation
ASME SEC III D1 NB-5000 Article NB-5000 Examination
ASME SEC III D1 NB-6000 Article NB-6000 Testing
ASME SEC III D1 NB-7000 Article NB-7000 Overpressure Protection
ASME SEC III D1 NB-8000 Article NB-8000 Nameplates, Stamping, and Reports
ASME SEC III D1 NB SI UNITS SI Units
ASME SEC III D1 NC A99 1999 Addenda Summary of Changes
ASME SEC III D1 NC A98 1998 Addenda Summary of Changes
ASME SEC III D1 NC INTRO Introduction
ASME SEC III D1 NC-1000 Article NC-1000 Introduction
ASME SEC III D1 NC-2000 Article NC-2000 Material
ASME SEC III D1 NC-3000 Article NC-3000 Design
ASME SEC III D1 NC-4000 Article NC-4000 Fabrication and Installation
ASME SEC III D1 NC-5000 Article NC-5000 Examination
ASME SEC III D1 NC-6000 Article NC-6000 Testing
ASME SEC III D1 NC-7000 Article NC-7000 Overpressure Protection
ASME SEC III D1 NC-8000 Article NC-8000 Nameplates, Stamping, and Reports
ASME SEC III D1 NC SI UNITS SI Units
ASME SEC III D1 ND A99 1999 Addenda Summary of Changes
ASME SEC III D1 ND A98 1998 Addenda Summary of Changes
ASME SEC III D1 ND INTRO Introduction
ASME SEC III D1 ND-1000 Article ND-1000 Introduction
ASME SEC III D1 ND-2000 Article ND-2000 Material
ASME SEC III D1 ND-3000 Article ND-3000 Design
ASME SEC III D1 ND-4000 Article ND-4000 Fabrication and Installation
ASME SEC III D1 ND-5000 Article ND-5000 Examination
ASME SEC III D1 ND-6000 Article ND-6000 Testing
ASME SEC III D1 ND-7000 Article ND-7000 Overpressure Protection
ASME SEC III D1 ND-8000 Article ND-8000 Nameplates, Stamping, and Reports
ASME SEC III D1 ND SI UNITS SI Units
ASME SEC III D1 NE A99 1999 Addenda Summary of Changes
ASME SEC III D1 NE A98 1998 Addenda Summary of Changes
ASME SEC III D1 NE INTRO Introduction
ASME SEC III D1 NE-1000 Article NE-1000 Introduction
ASME SEC III D1 NE-2000 Article NE-2000 Material
ASME SEC III D1 NE-3000 Article NE-3000 Design
ASME SEC III D1 NE-4000 Article NE-4000 Fabrication and Installation
ASME SEC III D1 NE-5000 Article NE-5000 Examination
ASME SEC III D1 NE-6000 Article NE-6000 Testing
ASME SEC III D1 NE-7000 Article NE-7000 Overpressure Protection
ASME SEC III D1 NE-8000 Article NE-8000 Nameplates, Stamping, and Reports
ASME SEC III D1 NE SI UNITS SI Units
ASME SEC III D1 NF A99 1999 Addenda Summary of Changes
ASME SEC III D1 NF A98 1998 Addenda Summary of Changes
ASME SEC III D1 NF INTRO Introduction
ASME SEC III D1 NF-1000 Article NF-1000 Introduction
ASME SEC III D1 NF-2000 Article NF-2000 Material
ASME SEC III D1 NF-3000 Article NF-3000 Design
ASME SEC III D1 NF-4000 Article NF-4000 Fabrication and Installation
ASME SEC III D1 NF-5000 Article NF-5000 Examination
ASME SEC III D1 NF-8000 Article NF-8000 Certificates of Authorization and Certificates of Conformance
ASME SEC III D1 MA APP NF-I Appendix NF-I (In the Course of Preparation)
ASME SEC III D1 MA APP NF-II Appendix NF-II Design of Single Angle Members
ASME SEC III D1 MA APP NF-III Appendix NF-III Energy Absorbing Support Material
ASME SEC III D1 NMA APP NF-A Structural Bolt Preloading
ASME SEC III D1 NMA APP NF-B Design Allowable Stresses for Plate-, Shell-, and Linear-Type Supports
ASME SEC III D1 NF SI UNITS SI Units
ASME SEC III D1 NG A99 1999 Addenda Summary of Changes
ASME SEC III D1 NG A98 1998 Addenda Summary of Changes
ASME SEC III D1 NG INTRO Introduction
ASME SEC III D1 NG-1000 Article NG-1000 Introduction
ASME SEC III D1 NG-2000 Article NG-2000 Material
ASME SEC III D1 NG-3000 Article NG-3000 Design
ASME SEC III D1 NG-4000 Article NG-4000 Fabrication and Installation
ASME SEC III D1 NG-5000 Article NG-5000 Examination
ASME SEC III D1 NG-8000 Article NG-8000 Nameplates, Stamping, and Reports
ASME SEC III D1 NG SI UNITS SI Units
ASME SEC III D1 NH A99 1999 Addenda Summary of Changes
ASME SEC III D1 NH A98 1998 Addenda Summary of Changes
ASME SEC III D1 NH INTRO Introduction
ASME SEC III D1 NH-1000 Article NH-1000 Introduction
ASME SEC III D1 NH-2000 Article NH-2000 Material
ASME SEC III D1 NH-3000 Article NH-3000 Design
ASME SEC III D1 NH-4000 Article NH-4000 Fabrication and Installation
ASME SEC III D1 NH-5000 Article NH-5000 Examination
ASME SEC III D1 NH-6000 Article NH-6000 Testing
ASME SEC III D1 NH-7000 Article NH-7000 Overpressure Protection
ASME SEC III D1 NH MA I-14 Appendix I-14 Tables I-14.0
ASME SEC III D1 NH NMA X Appendix X Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications
ASME SEC III D1 NH NMA T Appendix T Rules for Strain, Deformation, and Fatigue Limits at Elevated Temperatures
ASME SEC III D1 NH SI SI Units
ASME SEC III D1 APP A99 1999 Addenda Summary of Changes
ASME SEC III D1 APP A98 1998 Addenda Summary of Changes
ASME SEC III D1 APP INTRO Introduction
ASME SEC III D1 MA APP I Appendix I Design Stress Intensity Values, Allowable Stresses, Material Properties, and Design Fatigue Curves
ASME SEC III D1 MA APP II Appendix II Experimental Stress Analysis
ASME SEC III D1 MA APP III Appendix III Basis for Establishing Design Stress Intensity Values and Allowable Stress Values
ASME SEC III D1 MA APP IV Appendix IV Approval of New Materials under the ASME Boiler and Pressure Vessel Code
ASME SEC III D1 MA APP V Appendix V Certificate Holders' Data Report Forms, Instructions, and Application Forms for Certificates of Authorization for Use of Code Symbol Stamps
ASME SEC III D1 MA APP VI Appendix VI Rounded Indications
ASME SEC III D1 MA APP VII Appendix VII Charts and Tables for Determining Shell Thickness of Cylindrical and Spherical Components under External Pressure
ASME SEC III D1 MA APP XI Appendix XI Rules for Bolted Flange Connections for Class 2 and 3 Components and Class MC Vessels
ASME SEC III D1 MA APP XII Appendix XII Design Considerations for Bolted Flange Connections
ASME SEC III D1 MA APP XIII Appendix XIII Design Based on Stress Analysis for Vessels Designed in Accordance with NC-3200
ASME SEC III D1 MA APP XIV Appendix XIV Design Based on Fatigue Analysis for Vessels Designed in Accordance with NC-3200
ASME SEC III D1 MA APP XVIII Appendix XVIII Capacity Conversions for Pressure Relief Valves
ASME SEC III D1 MA APP XIX Appendix XIX Integral Flat Head with a Large Opening
ASME SEC III D1 MA APP XX Appendix XX Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC III D1 MA APP XXI Appendix XXI Adhesive Attachment of Nameplates
ASME SEC III D1 MA APP XXII Appendix XXII Design of Reinforcement for Cone-to-Cylinder Junction under External Pressure
ASME SEC III D1 MA APP XXIII Appendix XXIII Qualifications and Duties of Specialized Professional Engineers
ASME SEC III D1 NMA APP A Appendix A Stress Analysis Methods
ASME SEC III D1 NMA APP B Appendix B Owner's Design Specifications
ASME SEC III D1 NMA APP C Appendix C Certificate Holder's Design Report
ASME SEC III D1 NMA APP D Appendix D Nonmandatory Preheat Procedures
ASME SEC III D1 NMA APP E Appendix E Minimum Bolt Cross-Sectional Area
ASME SEC III D1 NMA APP F Appendix F Rules for Evaluation of Service Loadings with Level D Service Limits
ASME SEC III D1 NMA APP G Appendix G Protection Against Nonductile Failure
ASME SEC III D1 NMA APP J Appendix J Owner's Design Specifications for Core Support Structures
ASME SEC III D1 NMA APP K Appendix K Tolerances
ASME SEC III D1 NMA APP L Appendix L Class FF Flange Design for Class 2 and 3 Components and Class MC Vessels
ASME SEC III D1 NMA APP M Appendix M Recommendations for Control of Welding, Postweld Heat Treatment, and Nondestructive Examination of Welds
ASME SEC III D1 NMA APP N Appendix N Dynamic Analysis Methods
ASME SEC III D1 NMA APP O Appendix O Rules for Design of Safety Valve Installations
ASME SEC III D1 NMA APP P Appendix P Contents of Certified Material Test Reports
ASME SEC III D1 NMA APP Q Appendix Q Design Rules for Clamp Connections
ASME SEC III D1 NMA APP R Appendix R Determination of Permissible Lowest Service Metal Temperature from TNDT for Classes 2 and MC Construction
ASME SEC III D1 NMA APP S Appendix S Pump Shaft Design Methods
ASME SEC III D1 NMA APP T Appendix T Recommended Tolerances for Reconciliation of Piping Systems
ASME SEC III D1 NMA APP U Appendix U Rules for Pump Internals
ASME SEC III D1 NMA APP V Appendix V Interruption of Code Work
ASME SEC III D1 NMA APP W Appendix W Environmental Effects on Components
ASME SEC III D1 APP SI UNITS SI Units
ASME SEC III D2 A2000 2000 Addenda Summary of Changes
ASME SEC III D2 A99 1999 Addenda Summary of Changes
ASME SEC III D2 A98 1998 Addenda Summary of Changes
ASME SEC III D2 INTRODUCTION Introduction
ASME SEC III D2 INTRO Introduction to Section III, Division 2
ASME SEC III D2 CC-1000 Article CC-1000 Introduction
ASME SEC III D2 CC-2000 Article CC-2000 Material
ASME SEC III D2 CC-3000 Article CC-3000 Design
ASME SEC III D2 CC-4000 Article CC-4000 Fabrication and Construction
ASME SEC III D2 CC-5000 Article CC-5000 Construction Testing and Examination
ASME SEC III D2 CC-6000 Article CC-6000 Structural Integrity Test of Concrete Containments
ASME SEC III D2 CC-7000 Article CC-7000 Overpressure Protection
ASME SEC III D2 CC-8000 Article CC-8000 Nameplates, Stamping, and Reports
ASME SEC III D2 MA APP I Appendix I Tables of Prestressing and Liner Material
ASME SEC III D2 MA APP II Appendix II Concrete Multiaxial Compressive Strength Modification
ASME SEC III D2 MA APP III Appendix III Glossary of Terms and Nomenclature
ASME SEC III D2 MA APP IV Appendix IV Approval of New Material
ASME SEC III D2 MA APP VI Appendix VI Rounded Indications
ASME SEC III D2 MA APP VII Appendix VII Qualifications of Concrete Inspection Personnel
ASME SEC III D2 MA APP IX Appendix IX Nondestructive Examination Methods
ASME SEC III D2 MA APP X Appendix X Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC III D2 MA APP XI Appendix XI Qualifications for Arc Welding Reinforcing Bars
ASME SEC III D2 NMA APP C Appendix C Typical CRV Load Combinations (Optional)
ASME SEC III D2 NMA APP D Appendix D Nonmandatory Preheat Procedures
ASME SEC III D2 NMA APP E Appendix E Certification of Level I and II Concrete Inspection Personnel
ASME SEC III D2 NMA APP F Appendix F Liner Dimensional Tolerances
ASME SEC III D2 NMA APP G Appendix G Certified Material Test Reports for Liner Materials
ASME SEC III D2 NMA APP H Appendix H Reinforcement Fabrication and Placing Tolerances
ASME SEC III D2 REF MTL Reference Material
ASME SEC III D2 CODES Codes, Standards, and Specifications Referenced in Text
ASME SEC III D2 SI UNITS SI Units
ASME SEC III D3 A99 1999 Addenda Summary of Changes
ASME SEC III D3 WB-8000 Article WB-8000 Nameplates, Stamping and Reports
ASME SEC III D3 A2000 2000 Addenda Summary of Changes
ASME SEC III D3 A98 1998 Addenda Summary of Changes
ASME SEC III D3 INTRODUCTION Introduction
ASME SEC III D3 WA-1000 Article WA-1000 Scope of Division 3
ASME SEC III D3 WA-2000 Article WA-2000 Design Basis for Containment Systems for Transport Packagings
ASME SEC III D3 WA-3000 Article WA-3000 Responsibilities and Duties
ASME SEC III D3 WA-4000 Article WA-4000 Quality Assurance
ASME SEC III D3 WA-5000 Article WA-5000 Authorized Inspection
ASME SEC III D3 WA-8000 Article WA-8000 Certificates of Authorization, Nameplates, Code Symbol Stamping, and Data Reports
ASME SEC III D3 WA-9000 Article WA-9000 Glossary
ASME SEC III D3 WB-1000 Article WB-1000 Introduction
ASME SEC III D3 WB-2000 Article WB-2000 Material
ASME SEC III D3 WB-3000 Article WB-3000 Design
ASME SEC III D3 WB-4000 Article WB-4000 Fabrication and Installation
ASME SEC III D3 WB-5000 Article WB-5000 Examination
ASME SEC III D3 WB-6000 Article WB-6000 Testing
ASME SEC III D3 REF MTL Reference Material
ASME SEC III D3 CODES Codes, Standards, and Specifications Referenced in Text
ASME SEC III SI UNITS SI Units
ASME SEC IV A99 Addenda 1999 Summary of Changes
ASME SEC IV A2000 2000 Addenda Summary of Changes
ASME SEC IV A98 Addenda 1998 Summary of Changes
ASME SEC IV INTRODUCTION INTRODUCTION
ASME SEC IV PT HG A-1 Article 1 Scope and Service Restrictions
ASME SEC IV PT HG A-2 Article 2 Material Requirements
ASME SEC IV PT HG A-3 Article 3 Design
ASME SEC IV PT HG A-4 Article 4 Pressure Relieving Devices
ASME SEC IV PT HG A-5 Article 5 Tests, Inspection, and Stamping
ASME SEC IV PT HG A-6 Article 6 Instruments, Fittings, and Controls
ASME SEC IV PT HG A-7 Article 7 Installation Requirements
ASME SEC IV PT HF A-1 Article 1 General
ASME SEC IV PT HF A-2 Article 2 Material Requirements
ASME SEC IV PT HF A-3 Article 3 Design Stresses and Minimum Thicknesses
ASME SEC IV PT HF-HW A-4 Article 4 General Requirements
ASME SEC IV PT HF-HW A-5 Article 5 Material Requirements
ASME SEC IV PT HF-HW A-6 Article 6 Welding Processes and Qualifications
ASME SEC IV PT HF-HW A-7 Article 7 Design of Weldments
ASME SEC IV PT HF-HW A-8 Article 8 Fabrication Requirements
ASME SEC IV PT HF-HW A-9 Article 9 Inspection
ASME SEC IV PT HF-HB A-10 Article 10 General Requirements
ASME SEC IV PT HF-HB A-11 Article 11 Material Requirements
ASME SEC IV PT HF-HB A-12 Article 12 Brazing Processes, Procedures, and Qualifications
ASME SEC IV PT HF-HB A-13 Article 13 Design
ASME SEC IV PT HF-HB A-14 Article 14 Fabrication Requirements
ASME SEC IV PT HF-HB A-15 Article 15 Inspection and Stamping
ASME SEC IV PT HC A-1 Article 1 General
ASME SEC IV PT HC A-2 Article 2 Material Requirements
ASME SEC IV PT HC A-3 Article 3 Design
ASME SEC IV PT HC A-4 Article 4 Tests
ASME SEC IV PT HC A-5 Article 5 Quality Control and Inspection
ASME SEC IV PT HLW INTRO Introduction
ASME SEC IV PT HLW A-1 Article 1 General
ASME SEC IV PT HLW A-2 Article 2 Material Requirements
ASME SEC IV PT HLW A-3 Article 3 Design
ASME SEC IV PT HLW A-4 Article 4 Design of Weldments
ASME SEC IV PT HLW A-5 Article 5 Tests
ASME SEC IV PT HLW A-6 Article 6 Inspection and Stamping
ASME SEC IV PT HLW A-7 Article 7 Controls
ASME SEC IV PT HLW A-8 Article 8 Installation Requirements
ASME SEC IV MA APP 1 Appendix 1 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC IV MA APP 2 Appendix 2 - Mandatory Codes, Standards, and Specifications Referenced in Text
ASME SEC IV MA APP 3 Appendix 3 - Mandatory Adhesive Attachment of Nameplates to Casing
ASME SEC IV MA APP 4 Appendix 4 - Mandatory Alternative Specification for Plates and Bars in Lieu of SA-36 for Flat Plates and Bars
ASME SEC IV MA APP 5 Appendix 5 - Mandatory Vacuum Boilers
ASME SEC IV NMA APP A Appendix A Approval of New Materials Under the ASME Boiler and Pressure Vessel Code
ASME SEC IV NMA APP B Appendix B Method of Checking Safety Valve and Safety Relief Valve Capacity by Measuring Maximum Amount of Fuel That Can Be Burned
ASME SEC IV NMA APP C Appendix C Examples of Method of Calculating a Welded Ring Reinforced Furnace
ASME SEC IV NMA APP D Appendix D Examples of Methods of Computation of Openings in Boiler Shells
ASME SEC IV NMA APP E Appendix E Terminology
ASME SEC IV NMA APP F Appendix F Quality Control System
ASME SEC IV NMA APP H Appendix H List of Abbreviations and Addresses
ASME SEC IV NMA APP I Appendix I Specification for Test Method for Water Absorption of Plastics ASTM D 570-81 Reapproved 1988
ASME SEC IV NMA APP K Appendix K Guide to Information Appearing on Certificate of Authorization
ASME SEC IV NMA APP L Appendix L Guide to Manufacturer's Data Report Forms
ASME SEC IV SI UNITS SI Units
ASME SEC IV INDEX Index
ASME SEC V A2000 2000 Addenda Summary of Changes
ASME SEC V A99 1999 Addenda Summary of Changes
ASME SEC V A98 1998 Addenda Summary of Changes
ASME SEC V INTRODUCTION Introduction
ASME SEC V A-1 Article 1 General Requirements
ASME SEC V A-2 Article 2 Radiographic Examination
ASME SEC V A-4 Article 4 Ultrasonic Examination Methods for Inservice Inspection
ASME SEC V A-5 Article 5 Ultrasonic Examination Methods for Materials and Fabrication
ASME SEC V A-6 Article 6 Liquid Penetrant Examination
ASME SEC V A-7 Article 7 Magnetic Particle Examination
ASME SEC V A-8 Article 8 Eddy Current Examination of Tubular Products
ASME SEC V A-9 Article 9 Visual Examination
ASME SEC V A-10 Article 10 Leak Testing
ASME SEC V A-11 Article 11 Acoustic Emission Examination of Fiber-Reinforced Plastic Vessels
ASME SEC V A-12 Article 12 Acoustic Emission Examination of Metallic Vessels During Pressure Testing
ASME SEC V A-13 Article 13 Continuous Acoustic Emission Monitoring
ASME SEC V B SE-94 SE-94 Standard Guide for Radiographic Testing ASTM E 94-93
ASME SEC V B SE-142 SE-142 Standard Method for Controlling Quality of Radiographic Testing ASTM E 142-92
ASME SEC V B SE-186 SE-186 Standard Reference Radiographs for Heavy-Walled [2 to 4 1/2-in. (51 to 114-mm)] Steel Castings ASTM E 186-93
ASME SEC V B SE-242 SE-242 Standard Reference Radiographs for Appearances of Radiographic as Certain Parameters Are Changed ASTM E 242-91
ASME SEC V B SE-280 SE-280 Standard Reference Radiographs for Heavy-Walled [4 1/2 to 12-in. (114 to 305-mm)] Steel Castings ASTM E 280-93
ASME SEC V B SE-446 SE-446 Standard Reference Radiographs for Steel Castings up to 2 in. (51 mm) in Thickness ASTM E 446-93
ASME SEC V B SE-747 SE-747 Standard Practice for Design, Manufacture, and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for Radiology ASTM E747-97
ASME SEC V B SE-999 SE-999 Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing ASTM E 999-95
ASME SEC V B SE-1025 SE-1025 Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology ASTM E1025-98
ASME SEC V B SE-1030 SE-1030 Standard Test Method for Radiographic Examination of Metallic Castings ASTM E 1030-95
ASME SEC V B SE-1079 SE-1079 Standard Practice for Calibration of Transmission Densitometers ASTM E 1079-97
ASME SEC V B SE-1114 SE-1114 Standard Test Method for Determining the Focal Size of Iridium-192 Industrial Radiographic Sources ASTM E 1114-92 (R1997)
ASME SEC V B SE-1165 SE-1165 Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging ASTM E 1416-96
ASME SEC V B SE-1255 SE-1255 Standard Practice for Radioscopy ASTM E 1255-96
ASME SEC V B SE-1416 SE-1416 Standard Test Method for Radioscopic Examination of Weldments ASTM E 1416-96
ASME SEC V B SE-1647 SE-1647 Standard Practice for Determining Contrast Sensitivity in Radioscopy ASTM E1647-94
ASME SEC V B SE-1815 SE-1815 Standard Test Method for Classification of Film Systems for Industrial Radiography ASTM E 1815-96
ASME SEC V B SA-388/SA-388M SA-388/SA-388M Standard Practice for Ultrasonic Examination of Heavy Steel Forgings ASTM A 388/A 388M-95
ASME SEC V B SA-435/SA-435M SA-435/SA-435M Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates ASTM A 435/A 435M-90 (1996)
ASME SEC V B SA-577/SA-577M SA-577/SA-577M Standard Specification for Ultrasonic Angle-Beam Examination of Steel Plates ASTM A 577/A 577M-90 (1996)
ASME SEC V B SA-578/SA-578M SA-578/SA-578M Standard Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications ASTM A 578/A 578M-96
ASME SEC V B SA-609/SA-609M SA-609/SA-609M Standard Practice for Castings, Carbon, Low-Alloy, and Martensitic Stainless Steel, Ultrasonic Examination Thereof ASTM A 609/A 609M-91 (1997)
ASME SEC V B SA-745/SA-745M SA-745/SA-745M Standard Practice for Ultrasonic Examination of Austenitic Steel Forgings ASTM A 745/A 745M-94
ASME SEC V B SB-509 SB-509 Specification for Supplementary Requirements for Nickel Alloy Plate for Nuclear Applications ASTM B509-77
ASME SEC V B SB-510 SB-510 Specification for Supplementary Requirements for Nickel Alloy Rod and Bar for Nuclear Applications ASTM B 510-77
ASME SEC V B SB-513 SB-513 Specification for Supplementary Requirements for Nickel Alloy Seamless Pipe and Tube for Nuclear Applications ASTM B 513-77
ASME SEC V B SB-548 SB-548 Standard Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels ASTM B548-90
ASME SEC V B SE-114 SE-114 Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Examination by the Contact Method ASTM E114-95
ASME SEC V B SE-213 SE-213 Standard Practice for Ultrasonic Inspection of Metal Pipe and Tubing ASTM E213-98
ASME SEC V B SE-214 SE-214 Standard Practice for Immersed Ultrasonic Examination by the Reflection Method Using Pulsed Longitudinal Waves ASTM E214-68 (1985)
ASME SEC V B SE-273 SE-273 Standard Practice for Ultrasonic Examination of Longitudinal Welded Pipe and Tubing ASTM E 273-93
ASME SEC V B SE-797 SE-797 Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method ASTM E797-95
ASME SEC V B SD-129 SD-129 Standard Test Method for Sulfur in Petroleum Products (General Bomb Method) ASTM D129-95
ASME SEC V B SD-516 SD-516 Standard Test Method for Sulfate Ion in Water ASTM D 516-90
ASME SEC V B SD-808 SD-808 Standard Test Method for Chlorine in New and Used Petroleum Products (Bomb Method) ASTM D808-95
ASME SEC V B SD-1552 SD-1552 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) ASTM D 1552-95
ASME SEC V B SE-165 SE-165 Standard Test Method for Liquid Penetrant Examination ASTM E165-95
ASME SEC V B SE-1209 SE-1209 Standard Test Method for Fluorescent Penetrant Examination Using the Water-Washable Process ASTM E1209-87
ASME SEC V B SE-1219 SE-1219 Standard Test Method for Fluorescent Penetrant Examination Using the Solvent-Removable Process ASTM E 1219-87
ASME SEC V B SE-1220 SE-1220 Standard Test Method for Visible Penetrant Examination Using the Solvent-Removable Process ASTM E 1220-87
ASME SEC V B SE-709 SE-709 Standard Guide for Magnetic Particle Examination ASTM E709-95
ASME SEC V B SE-215 SE-215 Recommended Practice for Standardizing Equipment for Electromagnetic Testing of Seamless Aluminum-Alloy Tube ASTM E 215-67 (1979)E2
ASME SEC V B SE-243 SE-243 Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes ASTM E243-97
ASME SEC V B SE-309 SE-309 Standard Practice for Examination of Steel Tubular Products Using Magnetic Saturation ASTM E309-83
ASME SEC V B SE-426 SE-426 Standard Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Austenitic Stainless Steel, and Similar Alloys ASTM E 426-88
ASME SEC V B SE-571 SE-571 Standard Practice for Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy Tubular Products ASTM E 571-82 (1988)
ASME SEC V B SE-432 SE-432 Standard Recommended Guide for the Selection of a Leak Testing Method ASTM E432-71 (1984)
ASME SEC V B SE-479 SE-479 Standard Guide for Preparation of a Leak Testing Specification ASTM E 479-91 (1996)
ASME SEC V B SD-2563 SD-2563 Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts ASTM D 2563-94
ASME SEC V B SE-650 SE-650 Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors ASTM E 650-97
ASME SEC V B SE-976 SE-976 Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response ASTM E 976-98
ASME SEC V B SE-1211 SE-1211 Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors ASTM E 1211-97
ASME SEC V B SE-1419 SE-1419 Standard Test Method for Examination of Seamless, Gas-Filled Pressure Vessels Using Acoustic Emission ASTM E 1419-96
ASME SEC V B SE-1316 SE-1316 Standard Terminology for Nondestructive Examinations ASTM E 1316-95b
ASME SEC V MA APP I Appendix I - Mandatory Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC V SI UNITS SI Units
ASME SEC VI A99 1999 Addenda Summary of Changes
ASME SEC VI A2000 2000 Addenda Summary of Changes
ASME SEC VI A98 1998 Addenda Summary of Changes
ASME SEC VI INTRODUCTION Introduction
ASME SEC VI 1 1. General
ASME SEC VI 2 2. Types of Boilers
ASME SEC VI 3 3. Accessories and Installation
ASME SEC VI 4 4. Fuels
ASME SEC VI 5 5. Fuel Burning Equipment and Fuel Burning Controls
ASME SEC VI 6 6. Boiler Room Facilities
ASME SEC VI 7 7. Operation, Maintenance, and Repair - Steam Boilers
ASME SEC VI 8 8. Operation, Maintenance, and Repair - Hot Water Boilers and Hot Water Heating Boilers
ASME SEC VI 9 9. Water Treatment
ASME SEC VI EXHIBITS Exhibits
ASME SEC VI EX A Exhibit A
ASME SEC VI EX B Exhibit B
ASME SEC VI EX C Exhibit C
ASME SEC VI MA APP I Appendix I - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC VI SI UNITS SI Units
ASME SEC VI INDEX Index
ASME SEC VII A2000 2000 Addenda Summary of Changes
ASME SEC VII A99 1999 Addenda Summary of Changes
ASME SEC VII A98 1998 Addenda Summary of Changes
ASME SEC VII INTRODUCTION Introduction
ASME SEC VII SUBSEC C1 Subsection C1 Fundamentals
ASME SEC VII SUBSEC C2 Subsection C2 Boiler Operation
ASME SEC VII SUBSEC C3 Subsection C3 Boiler Auxiliaries
ASME SEC VII SUBSEC C4 Subsection C4 Appurtenances
ASME SEC VII SUBSEC C5 Subsection C5 Instrumentation, Controls, and Interlocks
ASME SEC VII SUBSEC C6 Subsection C6 Inspection
ASME SEC VII SUBSEC C7 Subsection C7 Repairs, Alterations, and Maintenance
ASME SEC VII SUBSEC C8 Subsection C8 Control of Internal Chemical Conditions
ASME SEC VII SUBSEC C9 Subsection C9 Preventing Boiler Failures
ASME SEC VII MA APP I Appendix I - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC VII NMA A Appendix A Procedures for Care and Maintenance of Package Boilers
ASME SEC VII NMA B Appendix B Watertube Boilers - Maintenance Checks
ASME SEC VII NMA C Appendix C Watertube Boilers - Operating Checks Relating to Maintenance
ASME SEC VII NMA D Appendix D Firetube Boilers - Maintenance Checks
ASME SEC VII NMA E Appendix E Firetube Boilers - Operating Checks Relating to Maintenance
ASME SEC VII GLOSSARY Glossary
ASME SEC VII SI UNITS SI Units
ASME SEC VIII D1 NMA APP H Appendix H Guidance to Accommodate Loadings Produced by Deflagration
ASME SEC VIII D1 A2000 2000 Addenda Summary of Changes
ASME SEC VIII D1 A99 1999 Addenda Summary of Changes
ASME SEC VIII D1 A98 1998 Addenda Summary of Changes
ASME SEC VIII D1 INTRODUCTION Introduction
ASME SEC VIII D1 A PT UG Part UG General Requirements for All Methods of Construction and All Materials
ASME SEC VIII D1 B PT UW Part UW Requirements for Pressure Vessels Fabricated by Welding
ASME SEC VIII D1 B PT UF Part UF Requirements for Pressure Vessels Fabricated by Forging
ASME SEC VIII D1 B PT UB Part UB Requirements for Pressure Vessels Fabricated by Brazing
ASME SEC VIII D1 C PT UCS Part UCS Requirements for Pressure Vessels Constructed of Carbon and Low Alloy Steels
ASME SEC VIII D1 C PT UNF Part UNF Requirements for Pressure Vessels Constructed of Nonferrous Materials
ASME SEC VIII D1 C PT UHA Part UHA Requirements for Pressure Vessels Constructed of High Alloy Steel
ASME SEC VIII D1 C PT UCI Part UCI Requirements for Pressure Vessels Constructed of Cast Iron
ASME SEC VIII D1 C PT UCL Part UCL Requirements for Welded Pressure Vessels Constructed of Material with Corrosion Resistant Integral Cladding, Weld Metal Overlay Cladding, or with Applied Linings
ASME SEC VIII D1 C PT UCD Part UCD Requirements for Pressure Vessels Constructed of Cast Ductile Iron
ASME SEC VIII D1 C PT UHT Part UHT Requirements for Pressure Vessels Constructed of Ferritic Steels with Tensile Properties Enhanced by Heat Treatment
ASME SEC VIII D1 C PT ULW Part ULW Requirements for Pressure Vessels Fabricated by Layered Construction
ASME SEC VIII D1 C PT ULT Part ULT Alternative Rules for Pressure Vessels Constructed of Materials Having Higher Allowable Stresses at Low Temperature
ASME SEC VIII D1 C TABLES Tables
ASME SEC VIII D1 MA APP 1 Appendix 1 Supplementary Design Formulas
ASME SEC VIII D1 MA APP 2 Appendix 2 Rules for Bolted Flange Connections with Ring Type Gaskets
ASME SEC VIII D1 MA APP 3 Appendix 3 Definitions
ASME SEC VIII D1 MA APP 4 Appendix 4 Rounded Indications Charts Acceptance Standard for Radiographically Determined Rounded Indications in Welds
ASME SEC VIII D1 MA APP 6 Appendix 6 Methods for Magnetic Particle Examination (MT)
ASME SEC VIII D1 MA APP 7 Appendix 7 Examination of Steel Castings
ASME SEC VIII D1 MA APP 8 Appendix 8 Methods for Liquid Penetrant Examination (PT)
ASME SEC VIII D1 MA APP 9 Appendix 9 Jacketed Vessels
ASME SEC VIII D1 MA APP 10 Appendix 10 Quality Control System
ASME SEC VIII D1 MA APP 11 Appendix 11 Capacity Conversions for Safety Valves
ASME SEC VIII D1 MA APP 12 Appendix 12 Ultrasonic Examination of Welds (UT)
ASME SEC VIII D1 MA APP 13 Appendix 13 Vessels of Noncircular Cross Section
ASME SEC VIII D1 MA APP 14 Appendix 14 Integral Flat Heads with a Large, Single, Circular, Centrally Located Opening
ASME SEC VIII D1 MA APP 16 Appendix 16 Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC VIII D1 MA APP 17 Appendix 17 Dimpled or Embossed Assemblies
ASME SEC VIII D1 MA APP 18 Appendix 18 Adhesive Attachment of Nameplates
ASME SEC VIII D1 MA APP 19 Appendix 19 Electrically Heated or Gas Fired Jacketed Steam Kettles
ASME SEC VIII D1 MA APP 20 Appendix 20 Hubs of Tubesheets and Flat Heads Machined from Plate
ASME SEC VIII D1 MA APP 21 Appendix 21 Jacketed Vessels Constructed of Work-Hardened Nickel
ASME SEC VIII D1 MA APP 22 Appendix 22 Integrally Forged Vessels
ASME SEC VIII D1 MA APP 23 Appendix 23 External Pressure Design of Copper, Copper Alloy, and Titanium Alloy Condenser and Heat Exchanger Tubes with Integral Fins
ASME SEC VIII D1 MA APP 24 Appendix 24 Design Rules for Clamp Connections
ASME SEC VIII D1 MA APP 25 Appendix 25 Acceptance of Testing Laboratories and Authorized Observers for Capacity Certification of Pressure Relief Valves
ASME SEC VIII D1 MA APP 26 Appendix 26 Pressure Vessel and Heat Exchanger Expansion Joints
ASME SEC VIII D1 MA APP 27 Appendix 27 Alternative Requirements for Glass-Lined Vessels
ASME SEC VIII D1 MA APP 28 Appendix 28 Alternative Corner Weld Joint Detail for Box Headers for Air-Cooled Heat Exchangers
ASME SEC VIII D1 MA APP 29 Appendix 29 Requirements for Steel Bars of Special Section for Helically Wound Interlocking Strip Layered Pressure Vessels
ASME SEC VIII D1 MA APP 30 Appendix 30 Rules for Drilled Holes not Penetrating Through Vessel Wall
ASME SEC VIII D1 MA APP 31 Appendix 31 Rules for Cr-Mo Steels with Additional Requirements for Welding and Heat Treatment
ASME SEC VIII D1 NMA APP A Appendix A Basis for Establishing Allowable Loads for Tube-to-Tubesheet Joints
ASME SEC VIII D1 NMA APP C Appendix C Suggested Methods for Obtaining the Operating Temperature of Vessel Walls in Service
ASME SEC VIII D1 NMA APP D Appendix D Suggested Good Practice Regarding Internal Structures
ASME SEC VIII D1 NMA APP E Appendix E Suggested Good Practice Regarding Corrosion Allowance
ASME SEC VIII D1 NMA APP F Appendix F Suggested Good Practice Regarding Linings
ASME SEC VIII D1 NMA APP G Appendix G Suggested Good Practice Regarding Piping Reactions and Design of Supports and Attachments
ASME SEC VIII D1 NMA APP K Appendix K Sectioning of Welded Joints
ASME SEC VIII D1 NMA APP L Appendix L Examples Illustrating the Application of Code Formulas and Rules
ASME SEC VIII D1 NMA APP M Appendix M Installation and Operation
ASME SEC VIII D1 NMA APP P Appendix P Basis for Establishing Allowable Stress Values
ASME SEC VIII D1 NMA APP R Appendix R Preheating
ASME SEC VIII D1 NMA APP S Appendix S Design Considerations for Bolted Flange Connections
ASME SEC VIII D1 NMA APP T Appendix T Temperature Protection
ASME SEC VIII D1 NMA APP W Appendix W Guide for Preparing Manufacturer's Data Reports
ASME SEC VIII D1 NMA APP Y Appendix Y Flat Face Flanges with Metal-to-Metal Contact Outside the Bolt Circle
ASME SEC VIII D1 NMA APP AA Appendix AA Rules for the Design of Tubesheets
ASME SEC VIII D1 NMA APP CC Appendix CC Flanged and Flued or Flanged Only Expansion Joints
ASME SEC VIII D1 NMA APP DD Appendix DD Guide to Information Appearing on Certificate of Authorization (See Fig. DD-1)
ASME SEC VIII D1 NMA APP EE Appendix EE Half-Pipe Jackets
ASME SEC VIII D1 SI SI Units
ASME SEC VIII D2 MA APP 26 Appendix 26 - Mandatory Rules for Cr-Mo Steels with Additional Requirements for Welding and Heat Treatment
ASME SEC VIII D2 A99 1999 Addenda Summary of Changes
ASME SEC VIII D2 A2000 2000 Addenda Summary of Changes
ASME SEC VIII D2 A98 1998 Addenda Summary of Changes
ASME SEC VIII D2 INTRODUCTION Introduction
ASME SEC VIII D2 ART G-1 Article G-1 Scope and Jurisdiction
ASME SEC VIII D2 ART G-2 Article G-2 Organization of This Division
ASME SEC VIII D2 ART G-3 Article G-3 Responsibilities and Duties
ASME SEC VIII D2 ART M-1 Article M-1 General Requirements
ASME SEC VIII D2 ART M-2 Article M-2 Special Requirements for Ferrous Materials
ASME SEC VIII D2 ART M-3 Article M-3 Special Requirements for Ferritic Steels with Tensile Properties Enhanced by Quenching and Tempering
ASME SEC VIII D2 ART M-4 Article M-4 Special Requirements for Nonferrous Materials
ASME SEC VIII D2 ART M-5 Article M-5 Special Requirements for Bolting
ASME SEC VIII D2 ART M-6 Article M-6 Material Design Data
ASME SEC VIII D2 ART D-1 Article D-1 General
ASME SEC VIII D2 ART D-2 Article D-2 Shells of Revolution under Internal Pressure
ASME SEC VIII D2 ART D-3 Article D-3 Shells of Revolution under External Pressure
ASME SEC VIII D2 ART D-4 Article D-4 Welded Joints
ASME SEC VIII D2 ART D-5 Article D-5 Openings and Their Reinforcement
ASME SEC VIII D2 ART D-6 Article D-6 Nozzles and Other Connections
ASME SEC VIII D2 ART D-7 Article D-7 Flat Heads, Bolted, and Studded Connections
ASME SEC VIII D2 ART D-8 Article D-8 Quick-Actuating Closures
ASME SEC VIII D2 ART D-9 Article D-9 Attachments and Supports
ASME SEC VIII D2 ART D-10 Article D-10 Access and Inspection Openings
ASME SEC VIII D2 ART D-11 Article D-11 Special Requirements for Layered Vessels
ASME SEC VIII D2 ART F-1 Article F-1 General Fabrication Requirements
ASME SEC VIII D2 ART F-2 Article F-2 Welding Fabrication Requirements
ASME SEC VIII D2 ART F-3 Article F-3 Special Requirements for Tube-to-Tubesheet Welds
ASME SEC VIII D2 ART F-4 Article F-4 Heat Treatment of Weldments
ASME SEC VIII D2 ART F-5 Article F-5 Special Requirements for Welding Corrosion Resistant Integral or Weld Metal Overlay Clad or Lined Parts and for Composite Welds
ASME SEC VIII D2 ART F-6 Article F-6 Special Requirements for Ferritic Steels with Tensile Properties Enhanced by Quenching and Tempering
ASME SEC VIII D2 ART F-7 Article F-7 Special Requirements for Forged Fabrication
ASME SEC VIII D2 ART F-8 Article F-8 Special Fabrication Requirements for Layered Vessels
ASME SEC VIII D2 ART R-1 Article R-1 General Requirements
ASME SEC VIII D2 ART R-2 Article R-2 Material and Design Requirements
ASME SEC VIII D2 ART R-4 Article R-4 Marking and Stamping
ASME SEC VIII D2 ART R-5 Article R-5 Certification of Capacity of Safety and Safety Relief Valves
ASME SEC VIII D2 ART R-6 Article R-6 Provisions in Vessels for Installation of Pressure Relieving Devices
ASME SEC VIII D2 ART I-1 Article I-1 General Rules for Inspection
ASME SEC VIII D2 ART I-2 Article I-2 Inspection of Materials
ASME SEC VIII D2 ART I-3 Article I-3 Inspection of Welding
ASME SEC VIII D2 ART I-4 Article I-4 Final Inspection
ASME SEC VIII D2 ART I-5 Article I-5 Radiographic Examination
ASME SEC VIII D2 ART T-1 Article T-1 Testing Requirements
ASME SEC VIII D2 ART T-2 Article T-2 Impact Testing of Welds and Vessel Test Plates of Ferrous Materials
ASME SEC VIII D2 ART T-3 Article T-3 Hydrostatic Tests
ASME SEC VIII D2 ART T-4 Article T-4 Pneumatic Tests
ASME SEC VIII D2 ART T-5 Article T-5 Pressure Test Gages
ASME SEC VIII D2 ART S-1 Article S-1 Contents and Method of Stamping
ASME SEC VIII D2 ART S-2 Article S-2 Obtaining and Using Code Stamps
ASME SEC VIII D2 ART S-3 Article S-3 Report Forms and Maintenance of Records
ASME SEC VIII D2 ART S-4 Article S-4 Special Requirements for Layered Vessels
ASME SEC VIII D2 MA APP 1 Appendix 1 - Mandatory Basis for Establishing Design Stress Intensity Values See Appendix 2 of Section II, Part D
ASME SEC VIII D2 MA APP 2 Appendix 2 - Mandatory Charts for Determining Shell Thickness of Cylindrical and Spherical Vessels under External Pressure See Subpart 3 of Section II, Part D
ASME SEC VIII D2 MA APP 3 Appendix 3 - Mandatory Rules for Bolted Flange Connections
ASME SEC VIII D2 MA APP 4 Appendix 4 - Mandatory Design Based on Stress Analysis
ASME SEC VIII D2 MA APP 5 Appendix 5 - Mandatory Design Based on Fatigue Analysis
ASME SEC VIII D2 MA APP 6 Appendix 6 - Mandatory Experimental Stress Analysis
ASME SEC VIII D2 MA APP 8 Appendix 8 - Mandatory Rounded Indications Charts Acceptance Standard for Radiographically Determined Rounded Indications in Welds
ASME SEC VIII D2 MA APP 9 Appendix 9 - Mandatory Nondestructive Examination
ASME SEC VIII D2 MA APP 10 Appendix 10 - Mandatory Capacity Conversions for Safety Valves
ASME SEC VIII D2 MA APP 18 Appendix 18 - Mandatory Quality Control System
ASME SEC VIII D2 MA APP 19 Appendix 19 - Mandatory Definitions
ASME SEC VIII D2 MA APP 20 Appendix 20 - Mandatory Requirements for Hubs of Tubesheets and Flat Heads Machined from Plate
ASME SEC VIII D2 MA APP 21 Appendix 21 - Mandatory Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC VIII D2 MA APP 22 Appendix 22 - Mandatory Acceptance of Testing Laboratories and Authorized Observers for Capacity Certification of Pressure Relief Valves
ASME SEC VIII D2 MA APP 23 Appendix 23 - Mandatory Adhesive Attachment of Nameplates
ASME SEC VIII D2 MA APP 24 Appendix 24 - Mandatory Requirements for Steel Bars of Special Section for Helically Wound Interlocking Strip Layered Pressure Vessels
ASME SEC VIII D2 MA APP 25 Appendix 25 - Mandatory Rules for Drilled Holes not Penetrating Through Vessel Wall
ASME SEC VIII D2 NMA APP A Appendix A - Nonmandatory Installation and Operation
ASME SEC VIII D2 NMA APP B Appendix B - Nonmandatory Temperature Protection
ASME SEC VIII D2 NMA APP C Appendix C - Nonmandatory Suggested Methods for Obtaining the Operating Temperatures of Vessel Walls in Service
ASME SEC VIII D2 NMA APP D Appendix D - Nonmandatory Preheating
ASME SEC VIII D2 NMA APP E Appendix E - Nonmandatory Limited Service Temperatures for Nonferrous Materials See Appendix 6, Table 6-152, of Section II, Part D
ASME SEC VIII D2 NMA APP G Appendix G - Nonmandatory Examples Illustrating the Application of Code Formulas and Rules
ASME SEC VIII D2 NMA APP I Appendix I - Nonmandatory Guide for Preparing Manufacturer's Data Reports
ASME SEC VIII D2 NMA APP J Appendix J - Nonmandatory Basis for Establishing External Pressure Charts See Appendix 3 of Section II, Part D
ASME SEC VIII D2 NMA APP K Appendix K - Nonmandatory Selection and Treatment of High Alloy Steels
ASME SEC VIII D2 NMA APP L Appendix L - Nonmandatory Guide to Information Appearing on Certificate of Authorization See Fig. L-1
ASME SEC VIII D2 NMA APP M Appendix M - Nonmandatory Flange Rigidity
ASME SEC VIII D2 SI SI Units
ASME SEC VIII D3 A99 1999 Addenda Summary of Changes
ASME SEC VIII D3 A2000 2000 Addenda Summary of Changes
ASME SEC VIII D3 A98 1998 Addenda Summary of Changes
ASME SEC VIII D3 INTRODUCTION Introduction
ASME SEC VIII D3 ART KG-1 Article KG-1 Scope and Jurisdiction
ASME SEC VIII D3 ART KG-2 Article KG-2 Organization of this Division
ASME SEC VIII D3 ART KG-3 Article KG-3 Responsibilities and Duties
ASME SEC VIII D3 ART KG-4 Article KG-4 General Rules for Inspection
ASME SEC VIII D3 ART KM-1 Article KM-1 General Requirements
ASME SEC VIII D3 ART KM-2 Article KM-2 Mechanical Property Test Requirements for Metals
ASME SEC VIII D3 ART KM-3 Article KM-3 Supplementary Requirements for Bolting
ASME SEC VIII D3 ART KM-4 Article KM-4 Material Design Data
ASME SEC VIII D3 ART KD-1 Article KD-1 General
ASME SEC VIII D3 ART KD-2 Article KD-2 Basic Design Requirements
ASME SEC VIII D3 ART KD-3 Article KD-3 Fatigue Evaluation
ASME SEC VIII D3 ART KD-4 Article KD-4 Fracture Mechanics Evaluation
ASME SEC VIII D3 ART KD-5 Article KD-5 Design Using Autofrettage

huangyhg · 发表于 2009-4-26 14:35:50

目录（三）

ASME Y10.1 Glossary of Terms Concerning Letter Symbols R(1988)
ASME Y10.1
ASME Y10.11 Letter Symbols and Abbreviations for Quantities Used in Acoustics Revision of ASA Y10.11-53
ASME Y10.18 Letter Symbols for Illuminating Engineering R(1987)
ASME Y14.1 Decimal Inch Drawing Sheet Size and Format
ASME Y14.1M Metric Drawing Sheet Size and Format
ASME Y14.2M Line Conventions and Lettering
ASME Y14.2M
ASME Y14.3M Multiand Sectional Drawings Revision of ANSI Y14.3 - 1975 R(1999)
ASME Y14.4M Pictorial Drawing R(1999)
ASME Y14.5.1M Mathematical Definition of Dimensioning and Tolerancing Principles R(1999)
ASME Y14.5.2 Certification of Geometric Dimensioning and Tolerancing Professionals
ASME Y14.5M Dimensioning and Tolerancing R(1999)
ASME Y14.5M-1982 (HISTORICAL) DIMENSIONING AND TOLERANCING; ERRATA - FEBRUARY 1985 (R 1988)
ASME Y14.6 (Pending) Screw Thread Representation Comment Period Ends: 2000-09-12
ASME Y14.6 Screw Thread Representation R(1998)
ASME Y14.6AM Screw Thread Representation Metric Supplement to ANSI Y14.6-78 R(1998)
ASME Y14.7.1 Gear Drawing Standards - Part 1 for Spur, Helical, Double Helical and Rack Partial Revision of Y14.7-58 R(1998)
ASME Y14.7.2 Gear and Spline Drawing Standards Part 2 - Bevel and Hypoid Gears R(1999)
ASME Y14.8M Castings and Forgings
ASME Y14.13M Mechanical Spring Representation R(1998)
ASME Y14.18M Optical Parts R(1998)
ASME Y14.24 Types and Applications of Engineering Drawings Revision of ASME Y14.24M-1989
ASME Y14.26M Digital Representation for Communication of Product Definition Data
ASME Y14.26M
ASME Y14.32.1M Chassis Frames - Passenger Car and Light Truck - Ground Vechicle Practices R(1999)
ASME Y14.34M Associated Lists
ASME Y14.35M Revision of Engineering Drawings and Associated Documents
ASME Y14.36M Surface Texture Symbols
ASME Y14.38 Abbreviations and Acronyms Revision and Redesignation of ASME Y1.1-1989
ASME Y14.100M Engineering Drawing Practices
ASME Y14 REPORT Digital Representation of Physical Object Shapes
ASME Y14 REPORT
ASME Y14 REPORT 3 Guideline for Documenting of Computer Systems Used in Computer-Aided Preparation of Product Definition Data Design Requirements
ASME Y14 TECH REPT 4 Structural Language Format for Basic Shape Description
ASME Y32.2.3 Graphical Symbols for Pipe Fittings, Valves, and Piping Redesignation of Z32.2.3-49(1953) R(1999)
ASME Y32.2.4 Graphical Symbols for Heating, Ventilating, and Air Conditioning Redesignation of Z32.2.4-49 R(1998)
ASME Y32.2.6 Graphical Symbols for Heat-Power Apparatus Redesignation of Z32.2.6-50 R(1999)
ASME Y32.4 Graphic Symbols for Plumbing Fixtures for Diagrams Used in Architecture and Building Construction Revision of ANSI Y32.4-54 R(1999)
ASME Y32.7 Graphic Symbols for Railroad Maps and Profiles Revision of ANSI Y32.7-57 R(1994)
ASME Y32.10 Graphic Symbols for Fluid Power Diagrams R(1999)
ASME Y32.11 Graphical Symbols for Process Flow Diagrams in the Petroleum and Chemical Industries R(1998)
ASME Y32.18 Symbols for Mechanical and Acoustical Elements as Used in Schematic Diagrams R(1998)
ASME AIA MARCH-99 Organizations Holding Authorized Inspection Agency Certificates of Accreditation
ASME CHAN MARCH-96 Companies Holding Authorized Nuclear Inspection Agency Certificates of Accreditation
ASME FAP MARCH-98 Companies Holding FAP Certificates of Accreditation
ASME NUC NOVEMBER 2000 Companies Holding Nuclear Certificates
ASME NUC MARCH 2001
ASME PVHO MARCH-94 Companies Holding PVHO Certificates of Authorization
ASME QEI MARCH-99 Companies Holding QEI Certificates of Accreditation
ASME QEI MARCH-01
ASME QRO MARCH-99 Individuals Holding QRO Certificates of Certification
ASME RTP MARCH-00 Companies Holding RTP Certificates of Authorization
ASME RTP MARCH-01
ASME SPPE MARCH-98 Companies Holding SPPE Certificates of Authorization (for Use of the OCS Stamp) and Certificates of Accreditation
ASME PTC 1 General Instructions (Performance Test Codes)
ASME PTC 2 Definitions and Values (Performance Test Codes) R(1985)
ASME PTC 3.1 Diesel and Burner Fuels (Performance Test Codes) R(1992)
ASME PTC 3.2 Coal and Coke (Performance Test Codes)
ASME PTC 3.3 Gaseous Fuels (Performance Test Codes) R(1992)
ASME PTC 4 Fire Steam Generators Revision of ASME PTC 4.1-1964(R1991) (Performance Test Codes)
ASME PTC 4.2 Coal Pulverizers (Performance Test Codes) R(1997)
ASME PTC 4.3 Air Heaters (Performance Test Codes) R(1991)
ASME PTC 4.4 Gas Turbine Heat Recovery Steam Generators (Performance Test Codes) R(1992)
ASME PTC 5 Reciprocating Steam Engines (Performance Test Codes)
ASME PTC 6 Steam Turbines (Performance Test Codes)
ASME PTC 6 INT 1977-1983- INTERPRETATIONS TO STEAM TURBINES
ASME PTC 6 REPORT Guidance for Evaluation of Measurement Uncertainty in Performance Tests of Steam Turbines R(1997)
ASME PTC 6A Appendix A To Test Code for Steam Turbines; Errata - 1988 (R 1995)
ASME PTC 6A (Pending) Appendix To PTC 6 - Test Code for Steam Turbines Comkment Period Ends: 2000-09-12
ASME PTC 6S-70 REPORT SIMPLIFIED PROCEDURES FOR ROUTINE PERFORMANCE TESTS OF STEAM TURBINES (R 1985)
ASME PTC 6S REPORT Procedures for Routine Performance Tests of Steam Turbines (R 1995)
ASME PTC 7.1 Displacement Pumps (Performance Test Codes) R(1969)
ASME PTC 8.2 Centrifugal Pumps (Performance Test Codes)
ASME PTC 9 Displacement Compressors, Vacuum Pumps and Blowers Erratum - 1972 (Performance Test Codes) R(1997)
ASME PTC 11 Fans (Performance Test Codes) R(1995)
ASME PTC 11
ASME PTC 12.2 Performance Test Code on Steam Surface Condensers (Performance Test Codes) R(1988)
ASME PTC 12.2
ASME PTC 12.3 Performance Test Code on Deaerators (Performance Test Codes)
ASME PTC 12.3
ASME PTC 12.4 Moisture Separator Reheaters R(1997)
ASME PTC 12.5 (Pending) Single Phase Heat Exchangers Comment Period Ends: 2000-08-15
ASME PTC 17 Reciprocating Internal-Combustion Engines (Performance Test Codes) R(1997)
ASME PTC 18 Hydraulic Turbines (Performance Test Codes)
ASME PTC 18.1 Pumping Mode of Pump/Turbines (Performance Test Codes) R(1984)
ASME PTC 19.1 Test Uncertainty Instruments and Apparatus (Performance Test Codes)
ASME PTC 19.2 Part 2: Pressure Measurement Instruments and Apparatus (Performance Test Codes) R(1998)
ASME PTC 19.2
ASME PTC 19.3 Part 3: Temperature Measurement Instruments and Apparatus (Performance Test Codes) R(1998)
ASME PTC 19.5 Application Part II of Fluid Meters (Performance Test Codes)
ASME PTC 19.5
ASME PTC 19.5.1 Chapter 1: Weighing Scales Part 5: Measurement of Quantity of Materials Instruments and Apparatus (Performance Test Codes)
ASME PTC 19.7 Part 7: Measurement of Shaft Power Instruments and Apparatus (Performance Test Codes) R(1988)
ASME PTC 19.8 Part 8: Measurement of Indicated Power Instruments and Apparatus (Performance Test Codes) R(1985)
ASME PTC 19.10 Part 10: Flue and Exhaust Gas Analyses Instruments and Apparatus (Performance Test Codes)
ASME PTC 19.10
ASME PTC 19.11 Steam and Water Sampling, Conditioning, and Analysis in the Power Cycle (Performance Test Codes)
ASME PTC 19.11
ASME PTC 19.14 Part 14: Linear Measurements Instruments and Apparatus (Performance Test Codes)
ASME PTC 19.14
ASME PTC 19.22 Part 22: Digital Systems Techniques Instruments and Apparatus (Performance Test Codes) R(1998)
ASME PTC 19.22
ASME PTC 19.23 Part 23: Guidance Manual for Model Testing Instruments and Apparatus (Performance Test Codes) R(1985)
ASME PTC 19.23
ASME PTC 20.1 Speed and Load Governing Systems for Steam Turbine-Generator Units (Performance Test Codes) R(1988)
ASME PTC 20.1
ASME PTC 20.2 Overspeed Trip Systems for Steam Turbine-Generator Units (Performance Test Codes) R(1986)
ASME PTC 20.3 Pressure Control Systems Used on Steam Turbine-Generator Units (Performance Test Codes) R(1986)
ASME PTC 21 Particulate Matter Collection Equipment (Performance Test Codes)
ASME PTC 21
ASME PTC 22 Performance Test Code on Gas Turbines (Performance Test Codes)
ASME PTC 23 Atmospheric Water Cooling Equipment (Performance Test Codes) R(1997)
ASME PTC 24 Ejectors (Performance Test Codes) R(1982)
ASME PTC 25 Pressure Relief Devices
ASME PTC 25 SPECIAL ADDENDA Special Addenda to PTC 25-1994 Pressure Relief Devices
ASME PTC 26 Speed-Governing Systems for Internal Combustion Engine-Generator Units (Performance Test Codes)
ASME PTC 28 Determining the Properties of Fine Particulate Matter (Performance Test Codes) R(1985)
ASME PTC 29 Speed-Governing Systems for Hydraulic Turbine-Generator Units (Performance Test Codes) R(1985)
ASME PTC 30 Air Cooled Heat Exchangers R(1998)
ASME PTC 31 Ion Exchange Equipment (Performance Test Codes) R(1991)
ASME PTC 32.1 Nuclear Steam Supply Systems (Performance Test Codes) R(1992)
ASME PTC 33 Large Incinerators Appendix 33A-1980 (Performance Test Codes) R(1991)
ASME PTC 36 Measurement of Industrial Sound (Performance Test Codes) R(1998)
ASME PTC 38 Determining the Concentration of Particulate Matter in a Gas Stream (Performance Test Codes) R(1985)
ASME PTC 39.1 Condensate Removal Devices for Steam Systems (Performance Test Codes) R(1991)
ASME PTC 40 Flue Gas Desulfurization Units
ASME PTC 42 Wind Turbines R(1998)
ASME PTC 46 Performance Test Code on Overall Plant Performance
ASME PTC PM Performance Monitoring Guidelines for Steam Power Plants
ASME CC N1 SUPPLEMENT 4 BPVC 1998 Code Cases Nuclear Components Supplement 4; Non-Interfiled
ASME SEC I BPVC SECTION I Rules for Construction of Power Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC I ADD BPVC SECTION I 1999 Addenda, Rules for Construction of Power Boilers Non-Interfiled
ASME SEC II-A BPVC SECTION II Materials Part A - Ferrous Material Specifications Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC II-A ADD BPVC SECTION II 1999 Addenda, Materials Part A - Ferrous Material Specifications Non-Interfiled
ASME SEC II-B BPVC SECTION II Materials Part B - Nonferrous Material Specifications Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC II-B ADD BPVC SECTION II Materials Part B - Nonferrous Material Specifications Non-Interfiled
ASME SEC II-C BPVC SECTION II Materials Part C - Specifications for Welding Rods, Electrodes, and Filler Metals Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC II-C ADD BPVC SECTION II 1999 Addenda, Materials Part C - Specifications for Welding Rods, Electrodes, and Filler Metals Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC II-D BPVC SECTION II Materials Part D - Properties Non-Interfiled
ASME SEC II-D ADD BPVC SECTION II 1999 Addenda, Materials Part D - Properties Non-Interfiled
ASME SEC III NCA BPVC SECTION III Rules for Construction of Nuclear Power Plant Components SUBSECTION NCA General Requirements for DIVISION 1 and DIVISION 2 ACI 359:1998; Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III NCA ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components SUBSECTION NCA General Requirements for DIVISION 1 and DIVISION 2 ACI 359:1998; Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NB BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NB Class 1 Components Non-Interfiled
ASME SEC III D1 NB ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NB Class 1 Components Non-Interfiled
ASME SEC III D1 NC BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NC Class 2 Components Non-Interfiled
ASME SEC III D1 NC ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NC Class 2 Components Non-Interfiled
ASME SEC III D1 ND BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION ND Class 3 Components Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 ND ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION ND Class 3 Components Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NE BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NE Class MC Components Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NE ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NE Class MC Components Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NF BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NF Supports Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NF ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NF Supports Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NG BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NG Core Support Structures Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NG ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NG Core Support Structures Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 NH BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NH Class 1 Components in Elevated Temperature Service Non-Interfiled
ASME SEC III D1 NH ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NH Class 1 Components in Elevated Temperature Service Non-Interfiled
ASME SEC III D1 APPENDICES BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - APPENDICES Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III D1 APPENDICES ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - APPENDICES Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC III DIVISION 2 BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 2: Code for Concrete Reactor Vessels and Containments ACI 359-98; Non-Interfiled
ASME SEC III D2 ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 2: Code for Concrete Reactor Vessels and Containments ACI 359-98; Non-Interfiled
ASME SEC III DIVISION 3 BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 3: Containment Systems and Transport Packagings for Spent Nuclear Fuel and High Level Radioactive Waste Non-Interfiled
ASME SEC III D3 ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 3: Containment Systems for Storage and Transport Packagings of Spent Nuclear Fuel and High Level Radioactive Material and Waste Non-Interfiled
ASME SEC IV BPVC SECTION IV Rules for Construction of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC IV ADD BPVC SECTION IV 1999 Addenda, Rules for Construction of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC V BPVC SECTION V Nondestructive Examination Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC V ADD BPVC SECTION V 1999 Addenda, Nondestructive Examination Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VI BPVC SECTION VI Recommended Rules for the Care and Operation of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VI ADD BPVC SECTION VI 1999 Addenda Recommended Rules for the Care and Operation of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VII BPVC SECTION VII Recommended Guidelines for the Care of Power Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VII ADD BPVC SECTION VII 1999 Addenda Recommended Guidelines for the Care of Power Boilers Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VIII DIVISION 1 BPVC SECTION VIII Rules for Construction of Pressure Vessels DIVISION 1 Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VIII D1 ADD BPVC SECTION VIII 1999 Addenda, Rules for Construction of Pressure Vessels DIVISION 1 Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VIII DIVISION 2 BPVC SECTION VIII Rules for Construction of Pressure Vessels DIVISION 2 - Alternative Rules Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VIII D2 ADD BPVC SECTION VIII 1999 Addenda, Rules for Construction of Pressure Vessels DIVISION 2 - Alternative Rules Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VIII DIVISION 3 BPVC SECTION VIII Rules for Construction of Pressure Vessels DIVISION 3 - Alternative Rules for High Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC VIII D3 ADD BPVC SECTION VIII 1999 Addenda, Rules for Construction of Pressure Vessels DIVISION 3 - Alternative Rules for Construction of High Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC IX BPVC SECTION IX Welding and Brazing Qualifications Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC IX ADD BPVC SECTION IX 1999 Addenda, Qualification Standard for Welding and Brazing Procedures, Welders, Brazers, and Welding and Brazing Operators Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC X BPVC SECTION X Fiber-Reinforced Plastic Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC X ADD BPVC SECTION X 1999 Addenda, Fiber-Reinforced Plastic Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC XI BPVC SECTION XI Rules for Inservice Inspection of Nuclear Power Plant Components Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME SEC XI ADD BPVC SECTION XI 1999 Addenda, Rules for Inservice Inspection of Nuclear Power Plant Components Non-Interfiled (Boiler and Pressure Vessel Codes)
ASME CC B1 BPVC 1998 Code Cases Boilers and Pressure Vessels Non-Interfiled
ASME CC B1 SUPPLEMENT 1 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 1; Non-Interfiled
ASME CC B1 SUPPLEMENT 2 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 2; Non-Interfiled
ASME CC B1 SUPPLEMENT 3 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 3; Non-Interfiled
ASME CC B1 SUPPLEMENT 4 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 4; Non-Interfiled
ASME CC N1 BPVC 1998 Code Cases Nuclear Components Non-Interfiled
ASME CC N1 SUPPLEMENT 1 BPVC 1998 Code Cases Nuclear Components Supplement 1; Non-Interfiled
ASME CC N1 SUPPLEMENT 2 BPVC 1998 Code Cases Nuclear Components Supplement 2; Non-Interfiled
ASME CC N1 SUPPLEMENT 3 BPVC 1998 Code Cases Nuclear Components Supplement 3; Non-Interfiled
ASME SEC I INT VOL 42 Interpretations Volume 42
ASME SEC I INT VOL 44 Interpretations Volume 44
ASME SEC I INT VOL 43 Interpretations Volume 43
ASME SEC II-A INT VOL 42 Interpretations Volume 42
ASME SEC II-A INT VOL 44 Interpretations Volume 44
ASME SEC III D1 INT VOL 42 Interpretations Volume 42
ASME SEC III D1 INT VOL 43 Interpretations Volume 43
ASME SEC III D1 INT VOL 44 Interpretations Volume 44
ASME SEC III D2 INT VOL 42 Interpretations Volume 42
ASME SEC III D2 INT VOL 43 Interpretations Volume 43
ASME SEC III D2 INT VOL 44 Interpretations Volume 44
ASME SEC IV INT VOL 42 Interpretations Volume 42
ASME SEC IV INT VOL 43 Interpretations Volume 43
ASME SEC IV INT VOL 44 Interpretations Volume 44
ASME SEC V INT VOL 42 Interpretations Volume 42
ASME SEC V INT VOL 43 Interpretations Volume 43
ASME SEC V INT VOL 44 Interpretations Volume 44
ASME SEC VIII D1 INT VOL 42 Interpretations Volume 42
ASME SEC VIII D1 INT VOL 43 Interpretations Volume 43
ASME SEC VIII D1 INT VOL 44 Interpretations Volume 44
ASME SEC VIII D2 INT VOL 42 Interpretations Volume 42
ASME SEC VIII D2 INT VOL 43 Interpretations Volume 43
ASME SEC VIII D2 INT VOL 44 Interpretations Volume 44
ASME SEC VIII D3 INT VOL 43 Interpretations Volume 43
ASME SEC IX INT VOL 42 Interpretations Volume 42
ASME SEC IX INT VOL 43 Interpretations Volume 43
ASME SEC IX INT VOL 44 Interpretations Volume 44
ASME SEC XI INT VOL 42 Interpretations Volume 42
ASME SEC XI INT VOL 43 Interpretations Volume 43
ASME SEC XI INT VOL 44 Interpretations Volume 44
ASME SEC I A2000 2000 Addenda Summary of Changes
ASME SEC I A99 1999 Addenda Summary of Changes
ASME SEC I A98 1998 Addenda Summary of Changes
ASME SEC I INTRODUCTION Introduction
ASME SEC I PT PG Part PG General Requirements for All Methods of Construction
ASME SEC I PT PW Part PW Requirements for Boilers Fabricated by Welding
ASME SEC I PT PR Part PR Requirements for Boilers Fabricated by Riveting Interfiled
ASME SEC I PT PB Part PB Requirements for Boilers Fabricated by Brazing Interfiled
ASME SEC I PT PWT Part PWT Requirements for Watertube Boilers
ASME SEC I PT PFT Part PFT Requirements for Firetube Boilers
ASME SEC I PT PFH Part PFH Optional Requirements for Feedwater Heater (When Located within Scope of Section I Rules) Interfiled
ASME SEC I PT PMB Part PMB Requirements for Miniature Boilers
ASME SEC I PT PEB Part PEB Requirements for Electric Boilers
ASME SEC I PT PVG Part PVG Requirements for Organic Fluid Vaporizers Interfiled
ASME SEC I MA I Appendix I - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee Interfiled
ASME SEC I NMA A Appendix A Explanation of the Code Containing Matter Not Mandatory Unless Specifically Referred to in the Rules of the Code
ASME SEC I FORMS/GUIDES Data Report Forms and Guides
ASME SEC I CODES Codes, Standards, and Specifications Referenced in Text
ASME SEC I SI UNITS SI Units Interfiled
ASME SEC I INDEX Index
ASME SEC II A SA-995 SA-995 Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts ASTM A 995-98
ASME SEC II A A99 1999 Addenda Summary of Changes
ASME SEC II A A2000 2000 Addenda Summary of Changes
ASME SEC II A A98 1998 Addenda Summary of Changes
ASME SEC II A INTRODUCTION Introduction
ASME SEC II A MA APP 1 Appendix 1 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC II A NMA APP A Appendix A - Nonmandatory Acceptable ASTM Editions
ASME SEC II A NMA APP B Appendix B Nonmandatory Guidelines on Multiple Marking of Materials
ASME SEC II A SI SI Units
ASME SEC II A SA-6/SA-6M SA-6/SA-6M Specification for General Requirements for Rolled Steel Plates, Shapes, Sheet Piling, and Bars for Structural Use ASTM A 6/A 6M-93b
ASME SEC II A SA-20/SA-20M SA-20/SA-20M Specification for General Requirements for Steel Plates for Pressure Vessels ASTM A 20/A 20M-93a
ASME SEC II A SA-29/SA-29M SA-29/SA-29M Specification for Steel Bars, Carbon and Alloy, Hot-Wrought and Cold-Finished, General Requirements for ASTM A 29/A 29M-93a
ASME SEC II A SA-36/SA-36M SA-36/SA-36M Specification for Carbon Structural Steel ASTM A 36/A 36M-96
ASME SEC II A SA-47 SA-47 Specification for Ferritic Malleable Iron Castings ASTM A 47-90
ASME SEC II A SA-53 SA-53 Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless ASTM A 53-96
ASME SEC II A SA-105/SA-105M SA-105/SA-105M Specification for Carbon Steel Forgings for Piping Applications ASTM A 105/A 105M-96
ASME SEC II A SA-106 SA-106 Specification for Seamless Carbon Steel Pipe for High-Temperature Service ASTM A 106-95
ASME SEC II A SA-134 SA-134 Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and over) ASTM A 134-93
ASME SEC II A SA-135 SA-135 Specification for Electric-Resistance-Welded Steel Pipe ASTM A 135-96
ASME SEC II A SA-178/SA-178M SA-178/SA-178M Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheated Tubes ASTM A 178/A 178M-95
ASME SEC II A SA-179/SA-179M SA-179/SA-179M Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A 179/A 179M-90a
ASME SEC II A SA-181/SA-181M SA-181/SA-181M Specification for Carbon Steel Forgings, for General-Purpose Piping ASTM A 181/A 181M-95b
ASME SEC II A SA-182/SA-182M SA-182/SA-182M Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service ASTM A 182/A 182M-98
ASME SEC II A SA-192/SA-192M SA-192/SA-192M Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
ASME SEC II A SA-193/SA-193M SA-193/SA-193M Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service ASTM A 193/A 193M-98a
ASME SEC II A SA-194/SA-194M SA-194/SA-194M Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High-Temperature Service ASTM A 194/A 194M-95a
ASME SEC II A SA-199/SA-199M SA-199/SA-199M Specification for Seamless Cold-Drawn Intermediate Alloy-Steel Heat-Exchanger and Condenser Tubes ASTM A 199/A 199M-92
ASME SEC II A SA-202/SA-202M SA-202/SA-202M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon ASTM A 202/A 202M-93
ASME SEC II A SA-203/SA-203M SA-203/SA-203M Specification for Pressure Vessel Plates, Alloy Steel, Nickel ASTM A 203/A 203M-93
ASME SEC II A SA-204/SA-204M SA-204/SA-204M Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum ASTM A 204/A 204M-93
ASME SEC II A SA-209/SA-209M SA-209/SA-209M Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes ASTM A 209/A 209M-95
ASME SEC II A SA-210/SA-210M SA-210/SA-210M Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes ASTM A 210/A 210M-95
ASME SEC II A SA-213/SA-213M SA-213/SA-213M Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes ASTM A 213/A 213M-95a
ASME SEC II A SA-214/SA-214M SA-214/SA-214M Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A 214/A 214M-90a
ASME SEC II A SA-216/SA-216M SA-216/SA-216M Specification for Steel Castings, Carbon, Suitable for Fusion Welding for High-Temperature Service ASTM A 216/A 216M-93
ASME SEC II A SA-217/SA-217M SA-217/SA-217M Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service ASTM A 217/A 217M-93
ASME SEC II A SA-225/SA-225M SA-225/SA-225M Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel ASTM A 225/A 225M-93
ASME SEC II A SA-226/SA-226M SA-226/SA-226M Specification for Electric-Resistance-Welded Carbon Steel Boiler and Superheater Tubes for High-Pressure Service ASTM A 226/A 226M-95
ASME SEC II A SA-232/SA-232M SA-232/SA-232M Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality Wire ASTM A 232/A 232M-91
ASME SEC II A SA-234/SA-234M SA-234/SA-234M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and Elevated Temperatures ASTM A 234/A 234M-95a
ASME SEC II A SA-240 SA-240 Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels ASTM A 240-97a
ASME SEC II A SA-249/SA-249M SA-249/SA-249M Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes ASTM A 249/A 249M-96a
ASME SEC II A SA-250/SA-250M SA-250/SA-250M Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes ASTM A 250/A 250M-95
ASME SEC II A SA-263 SA-263 Specification for Corrosion-Resisting Chromium Steel-Clad Plate, Sheet, and Strip ASTM A 263-94
ASME SEC II A SA-264 SA-264 Specification for Stainless Chromium-Nickel Steel-Clad Plate, Sheet, and Strip ASTM A 264-94a
ASME SEC II A SA-265 SA-265 Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate ASTM A 265-94a
ASME SEC II A SA-266/SA-266M SA-266/SA-266M Specification for Carbon Steel Forgings for Pressure Vessel Components ASTM A 266/A 266M-95
ASME SEC II A SA-268/SA-268M SA-268/SA-268M Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service ASTM A 268/A 268M-94
ASME SEC II A SA-275/SA-275M SA-275/SA-275M Specification for Magnetic Particle Examination of Steel Forgings ASTM A 275/A275M-96
ASME SEC II A SA-278 SA-278 Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures up to 650 Degrees F ASTM A 278-93
ASME SEC II A SA-283/SA-283M SA-283/SA-283M Specification for Low and Intermediate Tensile Strength Carbon Steel Plates ASTM A 283/A 283M-93
ASME SEC II A SA-285/SA-285M SA-285/SA-285M Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength ASTM A 285/A 285M-90
ASME SEC II A SA-299/SA-299M SA-299/SA-299M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon ASTM A 299/A 299M-90
ASME SEC II A SA-302/SA-302M SA-302/SA-302M Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel ASTM A 302/A 302M-93
ASME SEC II A SA-307 SA-307 Specification for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength ASTM A 307-93a
ASME SEC II A SA-311/SA-311M SA-311/SA-311M Specification for Steel Bars, Carbon, Stress-Relieved Cold-Drawn, Subject to Mechanical Property Requirements ASTM A 311/A 311M-90b
ASME SEC II A SA-312/SA-312M SA-312/SA-312M Specification for Seamless and Welded Austenitic Stainless Steel Pipes ASTM A 312/A 312M-95b
ASME SEC II A SA-320/SA-320M SA-320/SA-320M Specification for Alloy Steel Bolting Materials for Low-Temperature Service ASTM A 320/A 320M-94a
ASME SEC II A SA-325 SA-325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 KSI Minimum Tensile Strength ASTM A 325-94
ASME SEC II A SA-333/SA-333M SA-333/SA-333M Specification for Seamless and Welded Steel Pipe for Low-Temperature Service ASTM A 333/A 333M-94
ASME SEC II A SA-334/SA-334M SA-334/SA-334M Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service ASTM A 334/A 334M-96
ASME SEC II A SA-335/SA-335M SA-335/SA-335M Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service ASTM A 335/A 335M-95a
ASME SEC II A SA-336/SA-336M SA-336/SA-336M Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts ASTM A 336/A 336M-96
ASME SEC II A SA-350/SA-350M SA-350/SA-350M Specification for Forgings, Carbon and Low-Alloy Steel, Requiring Notch Toughness Testing for Piping Components ASTM A 350/A 350M-95b
ASME SEC II A SA-351/SA-351M SA-351/SA-351M Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts ASTM A 351/A 351M-94a
ASME SEC II A SA-352/SA-352M SA-352/SA-352M Specification for Steel Castings, Ferritic and Martensitic, for Pressure Containing Parts, Suitable for Low Temperature Service ASTM A 352/A 352M-93
ASME SEC II A SA-353/SA-353M SA-353/SA-353M Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel, Double-Normalized and Tempered ASTM A 353/A 353M-93
ASME SEC II A SA-354 SA-354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners ASTM A 354-95
ASME SEC II A SA-358/SA-358M SA-358/SA-358M Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature Service ASTM A 358/A 358M-95a
ASME SEC II A SA-369/SA-369M SA-369/SA-369M Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service ASTM A 369/A 369M-92
ASME SEC II A SA-370 SA-370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products ASTM A 370-96
ASME SEC II A SA-372/SA-372M SA-372/SA-372M Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels ASTM A 372/A 372M-95
ASME SEC II A SA-376/SA-376M SA-376/SA-376M Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service ASTM A 376/A 376M-93
ASME SEC II A SA-387/SA-387M SA-387/SA-387M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum ASTM A 387/A 387M-92 E1
ASME SEC II A SA-388/SA-388M SA-388/SA-388M Specification for Ultrasonic Examination of Heavy Steel Forgings ASTM A 388/A 388M-95
ASME SEC II A SA-395 SA-395 Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures ASTM A 395-88 (Reapproved 1993) E1
ASME SEC II A SA-403/SA-403M SA-403/SA-403M Specification for Wrought Austenitic Stainless Steel Piping Fittings ASTM A 403/A 403M-95
ASME SEC II A SA-409/SA-409M SA-409/SA-409M Specification for Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature Service ASTM A 409/A 409M-95a E1
ASME SEC II A SA-420/SA-420M SA-420/SA-420M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service ASTM A 420/A 420M-95
ASME SEC II A SA-423/SA-423M SA-423/SA-423M Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes ASTM A 423/A 423M-95
ASME SEC II A SA-414/SA-414M SA-414/SA-414M Specification for Steel, Sheet, Carbon, for Pressure Vessels ASTM A 414/A 414M-92 (R1993) E1
ASME SEC II A SA-426 SA-426 Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service ASTM A 426-92
ASME SEC II A SA-430/SA-430M SA-430/SA-430M Specification for Austenitic Steel Forged and Bored Pipe for High-Temperature Service ASTM A 430/A 430M-91
ASME SEC II A SA-435/SA-435M SA-435/SA-435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates ASTM A 435/A 435M-90
ASME SEC II A SA-437/SA-437M SA-437/SA-437M Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature Service ASTM A 437/A 437M-94
ASME SEC II A SA-449 SA-449 Specification for Quenched and Tempered Steel Bolts and Studs ASTM A 449-92b
ASME SEC II A SA-450/SA-450M SA-450/SA-450M Specification for General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel Tubes ASTM A 450/A 450M-96
ASME SEC II A SA-451 SA-451 Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature Service ASTM A 451-93
ASME SEC II A SA-452 SA-452 Specification for Centrifugally Cast Austenitic Steel Cold-Wrought Pipe for High-Temperature Service ASTM A 452-88
ASME SEC II A SA-453/SA-453M SA-453/SA-453M Specification for Bolting Materials, High-Temperature, 50 to 120 ksi (345 to 827 MPa) Yield Strength with Expansion Coefficients Comparable to Austenitic Steels ASTM A 453/A 453M-94
ASME SEC II A SA-455/SA-455M SA-455/SA-455M Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese ASTM A 455/A 455M-90
ASME SEC II A SA-476 SA-476 Specification for Ductile Iron Castings for Paper Mill Dryer Rolls ASTM A 476-90
ASME SEC II A SA-479/SA-479M SA-479/SA-479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels ASTM A 479/A 479M-95b
ASME SEC II A SA-480/SA-480M SA-480/SA-480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM A 480/A 480M-96
ASME SEC II A SA-484/SA-484M SA-484/SA-484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings ASTM A 484/A 484M-94b
ASME SEC II A SA-487/SA-487M SA-487/SA-487M Specification for Steel Castings Suitable for Pressure Service ASTM A 487/A 487M-93
ASME SEC II A SA-494/SA-494M SA-494/SA-494M Specification for Castings, Nickel and Nickel Alloy See Section II, Part B, SA-494/SA-494M
ASME SEC II A SA-508/SA-508M SA-508/SA-508M Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels ASTM A 508/A 508M-95
ASME SEC II A SA-515/SA-515M SA-515/SA-515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service ASTM A 515/A 515M-92
ASME SEC II A SA-516/SA-516M SA-516/SA-516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service ASTM A 516/A 516M-90
ASME SEC II A SA-517/SA-517M SA-517/SA-517M Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered ASTM A 517/A 517M-93
ASME SEC II A SA-522/SA-522M SA-522/SA-522M Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service ASTM A 522/A 522M-95
ASME SEC II A SA-524 SA-524 Specification for Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures ASTM A 524-93
ASME SEC II A SA-530/SA-530M SA-530/SA-530M Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe ASTM A 530/A 530M-96
ASME SEC II A SA-533/SA-533M SA-533/SA-533M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel ASTM A 533/A 533M-93
ASME SEC II A SA-537/SA-537M SA-537/SA-537M Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel ASTM A 537/A 537M-91
ASME SEC II A SA-540/SA-540M SA-540/SA-540M Specification for Alloy-Steel Bolting Materials for Special Applications ASTM A 540/A 540M-93
ASME SEC II A SA-541/SA-541M SA-541/SA-541M Specification for Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components ASTM A 541/A 541M-95
ASME SEC II A SA-542/SA-542M SA-542/SA-542M Specification for Pressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum, and Chromium-Molybdenum-Vanadium ASTM A 542/A 542M-95
ASME SEC II A SA-543/SA-543M SA-543/SA-543M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Nickel-Chromium-Molybdenum ASTM A 543/A 543M-93
ASME SEC II A SA-553/SA-553M SA-553/SA-553M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 Percent Nickel ASTM A 553/A 553M-93
ASME SEC II A SA-556/SA-556M SA-556/SA-556M Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes ASTM A 556/A 556M-90a (Reapproved 1995) E1
ASME SEC II A SA-557/SA-557M SA-557/SA-557M Specification for Electric-Resistance-Welded Carbon Steel Feedwater Heater Tubes ASTM A 557/A 557M-90a
ASME SEC II A SA-562/SA-562M SA-562/SA-562M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings ASTM A 562/A 562M-90
ASME SEC II A SA-563 SA-563 Specification for Carbon and Alloy Steel Nuts ASTM A 563-94
ASME SEC II A SA-564/SA-564M SA-564/SA-564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless and Heat-Resisting Steel Bars and Shapes ASTM A 564/A 564M-92a
ASME SEC II A SA-574 SA-574 Specification for Alloy Steel Socket-Head Screws ASTM A 325-80a and A 574-82
ASME SEC II A SA-577/SA-577M SA-577/SA-577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates ASTM A 577/A 577M-90
ASME SEC II A SA-578/SA-578M SA-578/SA-578M Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications ASTM A 578/A 578M-96
ASME SEC II A SA-587 SA-587 Specification for Electric-Resistance-Welded Low-Carbon Steel Pipe for the Chemical Industry ASTM A 587-93
ASME SEC II A SA-592/SA-592M SA-592/SA-592M Specification for High-Strength Quenched and Tempered Low-Alloy Steel Forged Fittings and Parts for Pressure Vessels ASTM A 592/A 592M-89 (R 1994) E1
ASME SEC II A SA-609/SA-609M SA-609/SA-609M Specification for Castings, Carbon, Low-Alloy, and Martensitic Stainless Steel, Ultrasonic Examination Thereof ASTM A 609/A 609M-91
ASME SEC II A SA-612/SA-612M SA-612/SA-612M Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service ASTM A 612/A 612M-90
ASME SEC II A SA-620/SA-620M SA-620/SA-620M Specification for Steel, Sheet, Carbon, Drawing Quality, Special Killed, Cold-Rolled ASTM A 620/A 620M-96
ASME SEC II A SA-638/SA-638M SA-638/SA-638M Specification for Precipitation Hardening Iron Base Superalloy Bars, Forgings, and Forging Stock for High-Temperature Service ASTM A 638/A 638M-92
ASME SEC II A SA-645/SA-645M SA-645/SA-645M Specification for Pressure Vessel Plates, 5% Nickel Alloy Steel, Specially Heat Treated ASTM A 645/A 645M-87
ASME SEC II A SA-649/SA-649M SA-649/SA-649M Specification for Forged Steel Rolls Used for Corrugating ASTM A 649/A 649M-94a
ASME SEC II A SA-660 SA-660 Specification for Centrifugally Cast Carbon Steel Pipe for High-Temperature Service ASTM A 660-91a
ASME SEC II A SA-662/SA-662M SA-662/SA-662M Specification for Pressure Vessel Plates, Carbon-Manganese, for Moderate and Lower Temperature Service ASTM A 662/A 622M-93
ASME SEC II A SA-666 SA-666 Specification for Austenitic Stainless Steel, Sheet, Strip, Plate, and Flat Bar ASTM A 666-96
ASME SEC II A SA-667/SA-667M SA-667/SA-667M Specification for Centrifugally Cast Dual Metal (Gray and White Cast Iron) Cylinders ASTM A 667/A 667M-87
ASME SEC II A SA-671 SA-671 Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures ASTM A 671-94
ASME SEC II A SA-672 SA-672 Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures ASTM A 672-94
ASME SEC II A SA-675/SA-675M SA-675/SA-675M Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties ASTM A 675/A 675M-90a (Reapproved 1995) E1
ASME SEC II A SA-688/SA-688M SA-688/SA-688M Specification for Welded Austenitic Stainless Steel Feedwater Heater Tubes ASTM A 688/A 688M-96
ASME SEC II A SA-691 SA-691 Specification for Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures ASTM A 691-93
ASME SEC II A SA-693 SA-693 Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM A 693-93
ASME SEC II A SA-695 SA-695 Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, for Fluid Power Applications ASTM A 695-90b
ASME SEC II A SA-696 SA-696 Specification for Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components ASTM A 696-90a (Reapproved 1995) E1
ASME SEC II A SA-703/SA-703M SA-703/SA-703M Specification for Steel Castings, General Requirements, for Pressure-Containing Parts ASTM A 703/A 703M-94
ASME SEC II A SA-705/SA-705M SA-705/SA-705M Specification for Age-Hardening Stainless and Heat-Resisting Steel Forgings ASTM A 705/A 705M-93
ASME SEC II A SA-723/SA-723M SA-723/SA-723M Specification for Alloy Steel Forgings for High-Strength Pressure Component Application ASTM A 723/A 723M-94
ASME SEC II A SA-724/SA-724M SA-724/SA-724M Specification for Pressure Vessel Plates, Carbon Steel, Quenched and Tempered, for Welded Layered Pressure Vessels ASTM A 724/A 724M-90
ASME SEC II A SA-727/SA-727M SA-727/SA-727M Specification for Forgings, Carbon Steel, for Piping Components with Inherent Notch Toughness ASTM A 727/A 727M-93
ASME SEC II A SA-731/SA-731M SA-731/SA-731M Specification for Seamless, Welded Ferritic, and Martensitic Stainless Steel Pipe ASTM A 731/A 731M-91
ASME SEC II A SA-736/SA-736M SA-736/SA-736M Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium and Nickel-Copper-Manganese-Molybdenum-Columbium Alloy Steel ASTM A 736/A 736M-88 (Reapproved 1994)
ASME SEC II A SA-737/SA-737M SA-737/SA-737M Specification for Pressure Vessel Plates, High-Strength, Low-Alloy Steel ASTM A 737/A 737M-87 (Reapproved 1991)
ASME SEC II A SA-738/SA-738M SA-738/SA-738M Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service ASTM A 738/A 738M-90
ASME SEC II A SA-739 SA-739 Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both ASTM A 739-90a (Reapproved 1995) E1
ASME SEC II A SA-745/SA-745M SA-745/SA-745M Practice for Ultrasonic Examination of Austenitic Steel Forgings ASTM A 745/A 745M-94
ASME SEC II A SA-747/SA-747M SA-747/SA-747M Specification for Precipitation Hardening Stainless Steel Castings ASTM A 747/A 747M-93
ASME SEC II A SA-748/SA-748M SA-748/SA-748M Specification for Statically Cast Chilled White Iron-Gray Iron Dual Metal Rolls for Pressure Vessel Use ASTM A 748/A 748M-87
ASME SEC II A SA-751 SA-751 Specification for Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products ASTM A 751-95
ASME SEC II A SA-765/SA-765M SA-765/SA-765M Specification for Carbon Steel and Low-Alloy Steel Pressure Vessel Component Forgings with Mandatory Toughness Requirements ASTM A 765/A 765M-94
ASME SEC II A SA-770/SA-770M SA-770/SA-770M Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications ASTM A 770/A 770M-86
ASME SEC II A SA-781/SA-781M SA-781/SA-781M Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use ASTM A 781/A 781M-94a
ASME SEC II A SA-788 SA-788 Specification for Steel Forgings, General Requirements ASTM A 788-94
ASME SEC II A SA-789/SA-789M SA-789/SA-789M Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service ASTM A 789/A 789M-95
ASME SEC II A SA-790/SA-790M SA-790/SA-790M Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe ASTM A 790/A 790M-95
ASME SEC II A SA-803/SA-803M SA-803/SA-803M Specification for Welded Ferritic Stainless Steel Feedwater Heater Tubes A 803/A 803M-96
ASME SEC II A SA-812/SA-812M SA-812/SA-812M Specification for Steel Sheet, High-Strength, Low-Alloy, Hot-Rolled, for Welded Layered Pressure Vessels ASTM A 812/A 812M-96
ASME SEC II A SA-813/SA-813M SA-813/SA-813M Specification for Single- or Double-Welded Austenitic Stainless Steel Pipe ASTM A 813/A 813M-95
ASME SEC II A SA-814/SA-814M SA-814/SA-814M Specification for Cold-Worked Welded Austenitic Stainless Steel Pipe ASTM A 814/A 814M-96
ASME SEC II A SA-815/SA-815M SA-815/SA-815M Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping Fittings ASTM A 815/A 815M-96 E1
ASME SEC II A SA-832/SA-832M SA-832/SA-832M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Vanadium ASTM A 832/A 832M-95
ASME SEC II A SA-834 SA-834 Specification for Common Requirements for Iron Castings for General Industrial Use ASTM A 834-94
ASME SEC II A SA-836/SA-836M SA-836/SA-836M Specification for Forgings, Titanium-Stabilized Carbon Steel, for Glass-Lined Piping and Pressure Vessel Service ASTM A 836/A 836M-95b
ASME SEC II A SA-841/SA-841M SA-841/SA-841M Specification for Steel Plates for Pressure Vessels, Produced by the Thermo-Mechanical Control Process (TMCP) ASTM A 841/A 841M-90
ASME SEC II A SA-905 SA-905 Specification for Steel Wire, Pressure Vessel Winding ASTM A 905-93
ASME SEC II A SF-568 SF-568 Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners ASTM F 568B-93a
ASME SEC II A SA/CSA-G40.21 SA/CSA-G40.21 Specification for Structural Quality Steels CAN/CSA G40.21-92
ASME SEC II A SA/EN 10028-2 SA/EN 10028-2 Specification for Flat Products Made of Steels for Pressure Purposes BS EN 10028-2-1993
ASME SEC II A SA/JIS G3118 SA/JIS G3118 Specification for Carbon Steel Plates for Pressure Vessels for Intermediate and Moderate Temperature Service JIS G3118-1987
ASME SEC II B A99 1999 Addenda Summary of Changes
ASME SEC II B A2000 2000 Addenda Summary of Changes
ASME SEC II B A98 1998 Addenda Summary of Changes
ASME SEC II B INTRODUCTION Introduction
ASME SEC II B MA APP 1 Appendix 1 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee
ASME SEC II B NMA APP A Appendix A - Nonmandatory Acceptable ASTM Editions
ASME SEC II B NMA APP B Appendix B - Nonmandatory Guidelines on Multiple Marking of Materials
ASME SEC II B SI SI Units
ASME SEC II B SB-26/SB-26M SB-26/SB-26M Specification for Aluminum-Alloy Sand Castings ASTM B 26/B 26M-97
ASME SEC II B SB-42 SB-42 Specification for Seamless Copper Pipe, Standard Sizes ASTM B 42-93
ASME SEC II B SB-43 SB-43 Specification for Seamless Red Brass Pipe, Standard Sizes ASTM B 43-94
ASME SEC II B SB-61 SB-61 Specification for Steam or Valve Bronze Castings ASTM B 61-93
ASME SEC II B SB-62 SB-62 Specification for Composition Bronze or Ounce Metal Castings ASTM B 62-93
ASME SEC II B SB-75 SB-75 Specification for Seamless Copper Tube ASTM B 75-95a
ASME SEC II B SB-96 SB-96 Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels ASTM B 96-93
ASME SEC II B SB-98 SB-98 Specification for Copper-Silicon Alloy Rod, Bar, and Shapes ASTM B 98-93
ASME SEC II B SB-108 SB-108 Specification for Aluminum-Alloy Permanent Mold Castings ASTM B 108-96a
ASME SEC II B SB-111 SB-111 Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock ASTM B 111-93
ASME SEC II B SB-127 SB-127 Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip ASTM B 127-93a
ASME SEC II B SB-135 SB-135 Specification for Seamless Brass Tube ASTM B 135-91b
ASME SEC II B SB-148 SB-148 Specification for Aluminum-Bronze Sand Castings ASTM B 148-97
ASME SEC II B SB-150 SB-150 Specification for Aluminum Bronze Rod and Bar ASTM B 150-95
ASME SEC II B SB-151 SB-151 Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar ASTM B 151-94
ASME SEC II B SB-152 SB-152 Specification for Copper Sheet, Strip, Plate, and Rolled Bar ASTM B 152-94
ASME SEC II B SB-160 SB-160 Specification for Nickel Rod and Bar ASTM B 160-93
ASME SEC II B SB-161 SB-161 Specification for Nickel Seamless Pipe and Tube ASTM B 161-93
ASME SEC II B SB-162 SB-162 Specification for Nickel Plate, Sheet, and Strip ASTM B 162-93a
ASME SEC II B SB-163 SB-163 Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes ASTM B 163-97a
ASME SEC II B SB-164 SB-164 Specification for Nickel-Copper Alloy Rod, Bar, and Wire ASTM B 164-93
ASME SEC II B SB-165 SB-165 Specification for Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube ASTM B 165-93
ASME SEC II B SB-166 SB-166 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06690, N06025, and N06045) and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Rod, Bar, and Wire ASTM B 166-95
ASME SEC II B SB-167 SB-167 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06690, N06025, and N06045) Seamless Pipe and Tube ASTM B 167-94a
ASME SEC II B SB-168 SB-168 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and N06690, N06025, and N06045) and Nickle-Chromium-Cobalt-Molybdenum Alloys (UNS N06617) Plate, Sheet, and Strip ASTM B 168-95a
ASME SEC II B SB-169 SB-169 Specification for Aluminum Bronze Plate, Sheet, Strip, and Rolled Bar ASTM B 169-95
ASME SEC II B SB-171 SB-171 Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers ASTM B 171-95
ASME SEC II B SB-187 SB-187 Specification for Copper Bar, Bus Bar, Rod, and Shapes ASTM B 187-94
ASME SEC II B SB-209 SB-209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate ASTM B 209-96
ASME SEC II B SB-210 SB-210 Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes ASTM B 210-95
ASME SEC II B SB-211 SB-211 Specification for Aluminum-Alloy Bar, Rod, and Wire ASTM B 211-95a
ASME SEC II B SB-221 SB-221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, and Profiles ASTM B 221-96
ASME SEC II B SB-234 SB-234 Specification for Aluminum and Aluminum Alloy-Drawn Seamless Tubes for Condensers and Heat Exchangers ASTM B 234-95
ASME SEC II B SB-241/SB-241M SB-241/SB-241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube ASTM B 241/B 241M-96
ASME SEC II B SB-247 SB-247 Specification for Aluminum-Alloy Die and Hand Forgings ASTM B 247-95a
ASME SEC II B SB-248 SB-248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar ASTM B 248-94
ASME SEC II B SB-249 SB-249 Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, and Shapes ASTM B 249-94a
ASME SEC II B SB-251 SB-251 Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube ASTM B 251-93
ASME SEC II B SB-265 SB-265 Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate ASTM B 265-98
ASME SEC II B SB-271 SB-271 Specification for Copper-Base Centrifugal Castings ASTM B 271-93a
ASME SEC II B SB-283 SB-283 Specification for Copper and Copper-Alloy Die Forgings (Hot Pressed) ASTM B 283-94
ASME SEC II B SB-308/SB-308M SB-308/SB-308M Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles ASTM B 308/B 308M-96
ASME SEC II B SB-315 SB-315 Specification for Seamless Copper Alloy Pipe and Tube ASTM B 315-93
ASME SEC II B SB-333 SB-333 Specification for Nickel-Molybdenum Alloy Plate, Sheet, and Strip ASTM B 333-95a
ASME SEC II B SB-335 SB-335 Specification for Nickel-Molybdenum Alloy Rod ASTM B 335-95
ASME SEC II B SB-337 SB-337 Specification for Seamless and Welded Titanium and Titanium Alloy Pipe ASTM B 337-95
ASME SEC II B SB-338 SB-338 Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers ASTM B 338-98
ASME SEC II B SB-348 SB-348 Specification for Titanium and Titanium Alloy Bars and Billets ASTM B 348-98
ASME SEC II B SB-359 SB-359 Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes with Integral Fins ASTM B 359-94
ASME SEC II B SB-363 SB-363 Specification for Seamless and Welded Unalloyed Titanium and Titanium Alloy Welding Fittings ASTM B 363-95
ASME SEC II B SB-366 SB-366 Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings ASTM B 366-97a
ASME SEC II B SB-367 SB-367 Specification for Titanium and Titanium Alloy Castings ASTM B 367-93
ASME SEC II B SB-369 SB-369 Specification for Copper-Nickel Alloy Castings ASTM B 369-93
ASME SEC II B SB-381 SB-381 Specification for Titanium and Titanium Alloy Forgings ASTM B 381-97
ASME SEC II B SB-395 SB-395 Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes ASTM B 395-93
ASME SEC II B SB-407 SB-407 Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube ASTM B 407-96
ASME SEC II B SB-408 SB-408 Specification for Nickel-Iron-Chromium Alloy Rod and Bar ASTM B 408-96
ASME SEC II B SB-409 SB-409 Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip ASTM B 409-96a
ASME SEC II B SB-423 SB-423 Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and UNS N08221) Seamless Pipe and Tube ASTM B 423-95
ASME SEC II B SB-424 SB-424 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825 and UNS N08221) Plate, Sheet, and Strip ASTM B 424-93
ASME SEC II B SB-425 SB-425 Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and UNS N08221) Rod and Bar ASTM B 425-93
ASME SEC II B SB-434 SB-434 Specification for Nickel-Molybdenum-Chromium-Iron Alloy (UNS N10003) Plate, Sheet, and Strip ASTM B 434-95
ASME SEC II B SB-435 SB-435 Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip ASTM B 435-97
ASME SEC II B SB-443 SB-443 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Plate, Sheet, and Strip ASTM B 443-93
ASME SEC II B SB-444 SB-444 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Pipe and Tube ASTM B 444-94
ASME SEC II B SB-446 SB-446 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Rod and Bar ASTM B 446-93
ASME SEC II B SB-462 SB-462 Specification for Forged or Rolled UNS N08020, UNS N08024, UNS N08026, and UNS N08367 Alloy Pipe Flanges, Forged Fittings, and Valves and Parts for Corrosive High-Temperature Service ASTM B 462-91
ASME SEC II B SB-463 SB-463 Specification for UNS N08020, UNS N08026, and UNS N08024 Alloy Plate, Sheet, and Strip ASTM B 463-93
ASME SEC II B SB-464 SB-464 Specification for Welded UNS N08020, UNS N08024, and UNS N08026 Alloy Pipe ASTM B 464-93
ASME SEC II B SB-466 SB-466 Specification for Seamless Copper-Nickel Pipe and Tube ASTM B 466-92a
ASME SEC II B SB-467 SB-467 Specification for Welded Copper-Nickel Pipe ASTM B 467-88
ASME SEC II B SB-468 SB-468 Specification for Welded UNS N08020, N08024, and N08026 Alloy Tubes ASTM B 468-93
ASME SEC II B SB-473 SB-473 Specification for UNS N08020, UNS N08026, and UNS N08024 Nickel Alloy Bar and Wire ASTM B473-95
ASME SEC II B SB-493 SB-493 Specification for Zirconium and Zirconium Alloy Forgings ASTM B 493-83 (R1993)
ASME SEC II B SA-494/SA-494M SA-494/SA-494M Specification for Castings, Nickel and Nickel Alloy ASTM A 494/A 494M-94
ASME SEC II B SB-505 SB-505 Specification for Copper-Base Alloy Continuous Castings ASTM B 505-93b
ASME SEC II B SB-511 SB-511 Specification for Nickel-Iron-Chromium-Silicon Alloy Bars and Shapes ASTM B 511-93
ASME SEC II B SB-514 SB-514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe ASTM B 514-95
ASME SEC II B SB-515 SB-515 Specification for Welded UNS N08120, UNS N08800, UNS N08810, and UNS N08811 Alloy Tubes ASTM B 515-95
ASME SEC II B SB-516 SB-516 Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600), UNS N06025, and UNS N06045 Tubes ASTM B 516-95
ASME SEC II B SB-517 SB-517 Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600), UNS N06025, and UNS N06045 Pipe ASTM B 517-95
ASME SEC II B SB-523 SB-523 Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes ASTM B 523-92
ASME SEC II B SB-535 SB-535 Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube ASTM B 535-94
ASME SEC II B SB-536 SB-536 Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Plate, Sheet, and Strip ASTM B 536-95
ASME SEC II B SB-543 SB-543 Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube ASTM B 543-91
ASME SEC II B SB-548 SB-548 Specification for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels ASTM B 548-90
ASME SEC II B SB-550 SB-550 Specification for Zirconium and Zirconium Alloy Bar and Wire ASTM B 550-92
ASME SEC II B SB-551 SB-551 Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate ASTM B 551-92
ASME SEC II B SB-564 SB-564 Specification for Nickel Alloy Forgings ASTM B 564-97a
ASME SEC II B SB-572 SB-572 Specification for UNS N06002, UNS N06230, UNS N12160 and UNS R30556 Rod ASTM B 572-97
ASME SEC II B SB-573 SB-573 Specification for Nickel-Molybdenum-Chromium-Iron Alloy (UNS N10003) Rod ASTM B 573-95
ASME SEC II B SB-574 SB-574 Specification for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod ASTM B 574-97
ASME SEC II B SB-575 SB-575 Specification for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Plate, Sheet, and Strip ASTM B 575-97
ASME SEC II B SB-581 SB-581 Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod ASTM B 581-93
ASME SEC II B SB-582 SB-582 Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and Strip ASTM B 582-92
ASME SEC II B SB-584 SB-584 Specification for Copper Alloy Sand Castings for General Applications ASTM B 584-93b
ASME SEC II B SB-599 SB-599 Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Plate, Sheet, and Strip ASTM B 599-92
ASME SEC II B SB-619 SB-619 Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe ASTM B 619-97
ASME SEC II B SB-620 SB-620 Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Plate, Sheet, and Strip ASTM B 620-93
ASME SEC II B SB-621 SB-621 Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod ASTM B 621-95
ASME SEC II B SB-622 SB-622 Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube ASTM B 622-97
ASME SEC II B SB-625 SB-625 Specification for UNS N08904, UNS N08925, UNS N08031, UNS N08932, and UNS N08926 Plate, Sheet, and Strip ASTM B 625-93a
ASME SEC II B SB-626 SB-626 Specification for Welded Nickel and Nickel-Cobalt Alloy Tube ASTM B 626-97
ASME SEC II B SB-637 SB-637 Specification for Precipitation-Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service ASTM B 637-93a

huangyhg · 发表于 2009-4-26 14:36:49

目录（二）

ASME B20.1 INTERPRETATIONS Interpretations to B20.1-1996 Safety Standard for Conveyors and Related Equipment Includes Interpretation No. A and B
ASME B20.1A Addenda to B20.1-1996 Safety Standard for Conveyors and Related Equipment
ASME B20.1B Addenda to B20.1 - 1996 Safety Standard for Conveyors and Related Equipment
ASME B27.8M General Purpose Metric Tapered and Reduced Cross Section Retaining Rings Type 3DM1 - Heavy Duty External Rings Type 3EM1 - Reinforced "E" Rings Type 3FM1 - "C" Type Rings R(1993)
ASME B27.8M
ASME B29.1M Precision Power Transmission Roller Chains, Attachments, and Sprockets R(1999)
ASME B29.2M Inverted Tooth (Silent) Chains and Sprockets (Revision of B29.2-1957 and B29.9-1958); Errata - July 1985 R(1999)
ASME B29.3M Double-Pitch Power Transmission Roller Chains and Sprockets R(1999)
ASME B29.4M Double-Pitch Conveyor Roller Chains, Attachments, and Sprockets R(1999)
ASME B29.6M Steel Detachable Link Chains, Attachments, and Sprockets
ASME B29.6M
ASME B29.8M Leaf Chains, Clevises, and Sheaves
ASME B29.10M Heavy Duty Offset Sidebar Power Transmission Roller Chains and Sprocket Teeth
ASME B29.11M Combination Chains, Attachments, and Sprocket Teeth
ASME B29.12M Steel Bushed Rollerless Chains, Attachments, and Sprocket Teeth
ASME B29.14M "H" Type Mill Chains, Attachments, and Sprocket Teeth
ASME B29.15M Steel Roller Type Conveyor Chains, Attachments, and Sprocket Teeth
ASME B29.16M Welded Steel Type Mill Chains, Attachments, and Sprocket Teeth Special Notice
ASME B29.17M Hinge Type Flat Top Conveyor Chains and Sprocket Teeth
ASME B29.18M Welded Steel-Type Drag Chains, Attachments, and Sprocket Teeth
ASME B29.19M Agricultural Roller Chains, Attachments, and Sprockets
ASME B29.19M
ASME B29.21M 700 Class Welded Steel and Cast Chains, Attachments and Sprockets for Water and Sewage Treatment Plants
ASME B29.22M Drop Forged Rivetless Chains, Sprocket Teeth Drive Chain/Drive Dogs
ASME B29.23M Flexible Chain Couplings R(1995)
ASME B29.24M Roller Load Chains for Overhead Hoists
ASME B29.25M Open Barrel Steel Pintle-Type Conveyor Chains, Attachments, and Sprockets
ASME B29.26M Fatigue Testing Power Transmission Roller Chain
ASME B29.300 Agricultural, Detachable, and Pintle Chains, Attachments, and Sprockets Incorporating ASME B29.6, B29.19, and B29.25
ASME B30.1 Jacks
ASME B30.2 Overhead and Gantry Cranes Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist
ASME B30.2 INTERPRETATIONS Interpretations to B30.2-1996 Overhead and Gantry Cranes Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist Includes Interpretation No. 1 Through 3
ASME B30.2A Addenda to B30.2-1996 Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist)
ASME B30.2B Addenda to B30.2-1996 Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist)
ASME B30.3 Construction Tower Cranes
ASME B30.3 INTERPRETATIONS Interpretations to B30.3-1996 Hammerhead Tower Cranes
ASME B30.3A Addenda to B30.3-1996 Construction Tower Cranes
ASME B30.3B Addenda to B30.3-1996 Construction Tower Cranes
ASME B30.3C Addenda to B30.3-1996 Construction Tower Cranes
ASME B30.4 Portal, Tower, and Pedestal Cranes
ASME B30.4 INTERPRETATIONS Interpretations to B30.4-1996 Portal, Tower, and Pedestal Cranes
ASME B30.4A Addenda to B30.4-1996 Portal, Tower, and Pedestal Cranes
ASME B30.4B Addenda to B30.4-1996 Portal, Tower and Pedestal Cranes
ASME B30.5 Mobile and Locomotive Cranes
ASME B30.5
ASME B30.5 INTERPRETATIONS Interpretations to B30.5-1994 Mobile and Locomotive Cranes
ASME B30.5A Addenda to B30.5-1994 Mobile and Locomotive Cranes
ASME B30.5B Addenda to B30.5-1994 Mobile and Locomotive Cranes
ASME B30.5C Addenda to B30.5 - 1994 Mobile and Locomotive Cranes
ASME B30.5D Addenda to B30.5 - 1994 Mobile and Locomotive Cranes
ASME B30.6 Derricks
ASME B30.6A Addenda to B30.6-1995 Derricks
ASME B30.6B Addenda to B30.6-1995 Derricks
ASME B30.7 Base Mounted Drum Hoists
ASME B30.7A Addenda to B30.7-1994 Base Mounted Drum Hoists
ASME B30.7B Addenda to B30.7-1994 Base Mounted Drum Hoists
ASME B30.7C Addenda to B30.7-1994 Base Mounted Drum Hoists
ASME B30.8 Floating Cranes and Floating Derricks
ASME B30.8 INTERPRETATIONS Interpretations to B30.8-1993 Floating Cranes and Floating Derricks
ASME B30.8A Addenda to B30.8-1993 Floating Cranes and Floating Derricks
ASME B30.8B Addenda to B30.8-1993 Floating Cranes and Floating Derricks
ASME B30.8C Addenda to B30.8-1993 Floating Cranes and Floating Derricks
ASME B30.9 Slings Safety Standard for Cableways, Cranes, Derricks, Hoists, Hooks, Jacks, and Slings FSC 3940; Should Be Used Instead of MIL-S-52432A
ASME B30.9 INTERPRETATIONS Interpretations to B30.9-1996 Slings
ASME B30.9A Addenda to B30.9-1996 Slings
ASME B30.9B Addenda to B30.9-1996 Slings
ASME B30.9C Addenda to B30.9-1996 Slings
ASME B30.10 Hooks
ASME B30.10 INTERPRETATIONS Interpretations to B30.10-1993 Hooks
ASME B30.10A Addenda to B30.10-1993 Hooks
ASME B30.10B Addenda to B30.10-1993 Hooks
ASME B30.11 Monorails and Underhung Cranes
ASME B30.11 INTERPRETATION Interpretations to B30.11 - 1998 Monorails and Underhung Cranes
ASME B30.11A Addenda to B30.11 - 1998 Monorails and Underhung Cranes
ASME B30.12 Handling Loads Suspended from Rotorcraft
ASME B30.12A Addenda to B30.12-1992 Handling Loads Suspended from Rotorcraft
ASME B30.12B Addenda to B30.12-1992 Handling Loads Suspended from Rotorcraft
ASME B30.13 Storage/Retrieval (S/R) Machines and Associated Equipment
ASME B30.13 INTERPRETATIONS Interpretations to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment
ASME B30.13A Addenda to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment
ASME B30.13B Addenda to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment
ASME B30.13C Addenda to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment
ASME B30.14 Side Boom Tractors
ASME B30.14A Addenda to B30.14-1996 Side Boom Tractors
ASME B30.16 Overhead Hoists (Underhung)
ASME B30.16 INTERPRETATIONS Interpretations to B30.16-1998 Overhead Hoists (Underhung)
ASME B30.17 Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist)
ASME B30.17 INTERPRETATIONS Interpretations to B30.17-1998 Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist)
ASME B30.18 Stacker Cranes (Top or Under Running Bridge, Multiple Girder with Top or Under Running Trolley Hoist)
ASME B30.20 Below-the-Hook Lifting Devices
ASME B30.20 INTERPRETATIONS Interpretations to B30.20-1993 Below-The-Hook Lifting Devices
ASME B30.20A Addenda to B30.20-1993 Below-The-Hook Lifting Devices
ASME B30.20B Addenda to B30.20-1993 Below-The-Hook Lifting Devices
ASME B30.20C Addenda to B30.20-1993 Below-The-Hook Lifting Devices
ASME B30.21 Manually Lever Operated Hoists
ASME B30.21 INTERPRETATIONS Interpretations to B30.2-1994 Manually Lever Operated Hoists
ASME B30.21A Addenda to B30.21-1994 Manually Lever Operated Hoists
ASME B30.21B Addenda to B30.21-1994 Manually Lever Operated Hoists
ASME B30.22 Articulating Boom Cranes
ASME B30.22 INTERPRETATIONS Interpretations to B30.22-1993 Articulating Boom Cranes
ASME B30.22A Addenda to B30.22-1993 Articulating Boom Cranes
ASME B30.22B Addenda to B30.22-1993 Articulating Boom Cranes
ASME B30.22C Addenda to B30.22-1993 Articulating Boom Cranes
ASME B30.22D Addenda to B30.22 - 1993 Articulating Boom Cranes
ASME B30.23 Personnel Lifting Systems
ASME B30.25 Scrap and Material Handlers
ASME B31.1 Power Piping
ASME B31.1 CASES NO. 25 Cases No. 25 to B31.1 Power Piping
ASME B31.1 CASES NO. 26 Cases No. 26 to B31.1 Power Piping
ASME B31.1 INTERPRETATIONS Interpretations to B31.1-1998 Power Piping Includes Interpretation No. 31
ASME B31.1A Addenda to B31.1-1998 Power Piping
ASME B31.2 Fuel Gas Piping
ASME B31.3 Process Piping
ASME B31.3 INTERPRETATIONS Interpretations to B31.3-1999 Process Piping Includes Interpretations No. 14 Through 17
ASME B31.3A Addenda to Process Piping
ASME B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and other Liquids
ASME B31.4 CASES NO. 4 Cases No. 4 to B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
ASME B31.4 INTERPRETATIONS Intrepretations to B31.4-1998 Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids Includes Interpretation No. 5
ASME B31.5 Refrigeration Piping Errata - 1993
ASME B31.5 INTERPRETATIONS Interpretations to B31.5-1992 Refrigreration Piping Includes Interpretation No. 5
ASME B31.5A Addenda to B31.5-1992 Refrigeration Piping
ASME B31.8 Gas Transmission and Distribution Piping Systems
ASME B31.9 Building Services Piping
ASME B31.9 INTERPRETATIONS Interpretations to B31.9-1996 Building Services Piping Includes Interpretation No. 1
ASME B31.11 Slurry Transportation Piping Systems Special Notice - 1990 R(1998)
ASME B31.11 INTERPRETATIONS Interpretations to B31.11-1989 Slurry Transportation Piping Systems
ASME B31.11A Addenda to B31.11-1989 Slurry Transportation Piping Systems
ASME B31G Manual for Determining the Remaining Strength of Corroded Pipelines a Supplement to ASME B31 Code for Pressure Piping
ASME B32.1 Preferred Thicknesses for Uncoated Thin Flat Metals (Under 0.025 in.) R(1994)
ASME B32.2 Preferred Diameters for Round Wire (0.500 Inches and Under) R(1994)
ASME B32.3M Preferred Metric Sizes for Flat Metal Products R(1994)
ASME B32.4M Preferred Metric Sizes for Round, Square, Rectangle and Hexagon Metal Products Revision of ANSI B32.4-1977 R(1994)
ASME B32.5 Preferred Metric Sizes for Tubular Metal Products Other Than Pipe Errata - 1996 R(1994)
ASME B32.6M Preferred Metric Equivalents of Inch Sizes for Tubular Metal Products Other Than Pipe Revision of ANSI B32.6 -1977 R(1994)
ASME B36.10M Welded and Seamless Wrought Steel Pipe
ASME B36.10M
ASME B36.19M Stainless Steel Pipe Revision of ANSI B36.19-1976 R(1994)
ASME B36.19M
ASME B40.2 Diaphragm Seals
ASME B40.3 Bimetallic Actuated Thermometers
ASME B40.5 Snubbers
ASME B40.6 Pressure Limiter Valves
ASME B40.100 Pressure Gauges and Gauge Attachments Incorporating ASME B40.1-1998 and ASME B40.7-1998
ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay)
ASME B47.1 Gage Blanks Revision of ANSI/ASME B47.1AM-1982 R(1999)
ASME B56.1 Safety Standard for Low Lift and High Lift Trucks
ASME B56.1 INTERPRETATIONS Interpretations to B56.1-1993 Safety Standard for Low Lift and High Lift Trucks
ASME B56.1A Addenda to B56.1-1993 Safety Standard for Low Lift and High Lift Trucks
ASME B56.5 INTERPRETATIONS Interpretations to B56.5-1993 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles
ASME B56.5A Addenda to B56.5-1993 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles
ASME B56.6 Safety Standard for Rough Terrain Forklift Trucks
ASME B56.6 INTERPRETATIONS Interpretations to B56.6-1993 Safety Standard for Rough Terrain Forklift Trucks
ASME B56.6A Addenda to B56.6-1993 Safety Standard for Rough Terrain Forklift Trucks
ASME B56.6B Addenda to B56.6-1992 Safety Standard for Rough Terrain Forklift Trucks
ASME B56.7 Safety Standard for Industrial Crane Trucks Special Notice - June 1988 R(1992)
ASME B56.8 INTERPRETATIONS Interpretations to B56.8-1993 Safety Standard for Personnel and Burden Carriers
ASME B56.8A Addenda to B56.8-1993 Safety Standard for Personnel and Burden Carriers
ASME B56.9 INTERPRETATIONS Interpretations to B56.9-1992 Safety Standard for Operator Controlled Industrial Tow Tractors
ASME B56.9A Addenda to B56.9-1992 Safety Standard for Operator Controlled Industrial Tow Tractors
ASME B56.10 Safety Standard for Manually Propelled High Lift Industrial Trucks Special Notice - October 1993
ASME B56.10
ASME B56.11.4 Hook-Type Forks and Fork Carriers for Powered Industrial Forklift Trucks Special Notice - February 1993
ASME B56.11.4
ASME B56.11.4A Addenda to B56.11.4-1992 Hook-Type Forks and Fork Carriers for Powered Industrial Forklift Trucks
ASME B56.11.5A Addenda to B56.11.5-1992 Measurement of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks
ASME B56.11.7 Liquid Propane Gas (LPG) Fuel Cylinders (Horizontal or Vertical) Mounting - Liquid Withdrawal - For Powered Industrial Trucks
ASME B73.1 (Pending) Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process Comment Period Ends: 2000-09-12
ASME B73.1M Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process Errata - August 1992 R(1999)
ASME B73.2M Specification for Vertical In-Line Centrifugal Pumps for Chemical Process R(1999)
ASME B73.3M Specification for Sealless Horizontal End Suction Centrifugal Pumps for Chemical Process
ASME B73.5M Specification for Thermoplastic and Thermoset Polymer Material Horizontal End Suction Centrifugal Pumps for Chemical Process
ASME B89.1.2M Calibration of Gage Blocks by Contact Comparison Methods (Through 20 in. and 500 mm)
ASME B89.1.5 Measurement of Plain External Diameters for Use as Master Discs or Cylindrical Plug Gages
ASME B89.1.6M Measurement of Qualified Plain Internal Diameters for Use as Master Rings and Ring Gages R(1997)
ASME B89.1.9M Precision Gage Blocks for Length Measurement (Through 20 in. and 500 mm) R(1997)
ASME B89.1.10M Dial Indicators (for Linear Measurements) Revision of ANSI B89.1.10-1978 R(1995)
ASME B89.3.1 Measurement of Out-Of-Roundness R(1997)
ASME B89.3.4M Axes of Rotation Methods for Specifying and Testing R(1992)
ASME B89.4.1 Methods for Performance Evaluation of Coordinate Measuring Machines Revision of ASME B89.1.12M-1990
ASME B89.4.1A Addenda to B89.4.1-1997 Methods for Performance Evaluation of Coordinate Measuring Machines
ASME B89.4.10 (Pending) Methods for Performance Evaluation of Coordinate Measuring Systems Software Comment Period Ends: 2000-09-12
ASME B89.6.2 Temperature and Humidity Environment for Dimensional Measurement R(1995)
ASME B89.7.2 Dimensional Measurement Planning
ASME B89 TECH PAPER Space Plate Test Recommendations for Coordinate Measuring Machines
ASME B89 TECH REPT Parametric Calibration of Coordinate Measuring Machines
ASME B94.2 Reamers
ASME B94.3 Straight Cut-Off Blades for Lathes and Screw Machines R(1995)
ASME B94.6 Knurling R(1995)
ASME B94.7 Hobs R(1995)
ASME B94.8 Inserted Blade Milling Cutter Bodies Revision of USAS B5.23-1958 R(1998)
ASME B94.9 Taps: Ground and Cut Threads (Inch and Metric Sizes)
ASME B94.11M Twist Drills
ASME B94.14 (Pending) Punches - Basic Head Type Comment Period Ends: 2000-08-15 R(2000)
ASME B94.14 Punches - Basic Head Type R(1995)
ASME B94.14
ASME B94.14.1 Punches - Basic Head Type (Metric) R(1995)
ASME B94.14.1 (Pending) Punches - Basic Head Type (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.16 (Pending) Retainers - Basic Ball-Lock Punch and Die Button, Light and Heavy Duty Comment Period End: 2000-08-15 R(2000)
ASME B94.16 Retainers - Basic Ball-Lock Punch and Die Button, Light and Heavy Duty R(1995)
ASME B94.16
ASME B94.16.1 (Pending) Retainers - Basic Ball-Lock Punch and Die Button Light and Heavy Duty (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.16.1 Retainers - Basic Ball-Lock Punch and Die Button Light and Heavy Duty (Metric) R(1995)
ASME B94.16.1
ASME B94.17 Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers R(1995)
ASME B94.17 (Pending) Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers Comment Period Ends: 2000-08-15 R(2000)
ASME B94.17.1 Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers (Metric) R(1995)
ASME B94.17.1 (Pending) Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.18 Punches - Basic Ball-Lock, Light and Heavy Duty Comment Period Ends: 2000-08-15
ASME B94.18.1 (Pending) Punches - Basic Ball-Lock Light and Heavy Duty (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.18.1 Punches - Basic Ball-Lock Light and Heavy Duty (Metric) R(1995)
ASME B94.18.1
ASME B94.19 Milling Cutters and End Mills
ASME B94.21 Gear Shaper Cutters R(1995)
ASME B94.22 (Pending) Punches-Variable Head Type Comment Period Ends: 2000-08-15 R(2000)
ASME B94.22 Punches-Variable, Head Type R(1995)
ASME B94.22
ASME B94.22.1 Punches-Variable, Head Type (Metric) R(1995)
ASME B94.22.1
ASME B94.22.1 (Pending) Punches-Variable, Head Type (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.23 Punch Guide Bushings - Variable, Press Fit R(1995)
ASME B94.23
ASME B94.23 (Pending) Punch Guide Bushings - Variable, Press Fit Comment Period Ends: 2000-08-15 R(2000)
ASME B94.27 Die Buttons Basic Taper Relief, Press Fit R(1995)
ASME B94.27
ASME B94.27 (Pending) Die Buttons Basic Taper Relief, Press Fit Comment Period Ends: 2000-08-15 R(2000)
ASME B94.27.1M (Pending) Die Buttons - Basic Taper Relief, Press Fit (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.27.1M Die Buttons - Basic Taper Relief, Press Fit (Metric) R(1995)
ASME B94.27.1M
ASME B94.28 (Pending) Die Buttons Basic Straight Relief, Press Fit Comment Period Ends: 2000-08-15 R(2000)
ASME B94.28 Die Buttons Basic Straight Relief, Press Fit R(1995)
ASME B94.28
ASME B94.28.1M Die Buttons - Basic Straight Relief, Press Fit (Metric) R(1995)
ASME B94.28.1M
ASME B94.28.1M (Pending) Die Buttons - Basic Straight Relief, Press Fit (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.29 Die Buttons - Basic Ball-Lock R(1995)
ASME B94.29
ASME B94.29 (Pending) Die Buttons - Basic Ball-Lock Comment Period Ends: 2000-08-15 R(2000)
ASME B94.29.1 (Pending) Die Buttons - Basic Ball-Lock (Metric) Comment Period Ends: 2000-08-15 R(2000)
ASME B94.29.1 Die Buttons - Basic Ball-Lock (Metric) R(1995)
ASME B94.29.1
ASME B94.30 Die Buttons Variable, Press Fit Comment Period Ends: 2000-08-15 R(1995)
ASME B94.31 Steel Rotary Slitting Knives and Steel Spacing Collars R(1995)
ASME B94.31 (Pending) Steel Rotary Slitting Knives and Steel Spacing Collars Comment Period Ends: 2000-08-15 R(2000)
ASME B94.33 Jig Bushings
ASME B94.33.1 Jig Bushings (Metric)
ASME B94.35 Drill Drivers, Split-Sleeve, Collet Type R(1995)
ASME B94.37M Roller Turner Type Cutting Tools, Single Point Revision of B94.37-1972 R(1985)
ASME B94.38 (Pending) Punches-Variable, Angle Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000)
ASME B94.38 Punches-Variable, Angle Head Type and Related Quill Bushings R(1995)
ASME B94.39 (Pending) Punches - Basic, Combination Angle Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000)
ASME B94.39 Punches - Basic, Combination Angle Head Type and Related Quill Bushings R(1995)
ASME B94.40 Punches - Wire Type R(1995)
ASME B94.40 (Pending) Punches - Wire Type Comment Period Ends: 2000-08-15 R(2000)
ASME B94.41 Punches - Basic, Angle Head Type and Related Quill Bushings R(1995)
ASME B94.41 (Pending) Punches - Basic, Angle Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000)
ASME B94.43 Die Buttons Variable, Press Fit, Headless and Head Type, Step Relief R(1995)
ASME B94.43 (Pending) Die Buttons Variable, Press Fit, Headless and Head Type, Step Relief Comment Period Ends: 2000-08-15 R(2000)
ASME B94.44 (Pending) Punches - Basic, Cylindrical Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000)
ASME B94.44 Punches - Basic, Cylindrical Head Type and Related Quill Bushings R(1995)
ASME B94.44
ASME B94.49 Spade Drill Blades and Spade Drill Holders R(1995)
ASME B94.50 Basic Nomenclature and Definitions for Single-Point Cutting Tools R(1995)
ASME B94.51M Specifications for Band Saw Blades (Metal Cutting)
ASME B94.52M Specifications for Hacksaw Blades
ASME B94.53 Solid Steel Rectangular Metal Cutting Squaring Shear Knives Dimensional Tolerances R(1984)
ASME B94.54 Specifications for Hole Saws, Hole Saw Arbors, and Hole Saw Accessories
ASME B94.55M Tool Life Testing with Single-Point Turning Tools Revision of ANSI B94.34-1946 and B94.36-1956 R(1995)
ASME B94.56 Gages - Functional, Ball-Lock Punches (Inch)
ASME B94.56.1M Gages - Functional, Ball-Lock Punches (Metric)
ASME B96.1 Welded Aluminum-Alloy Storage Tanks
ASME B106.1M (Withdrawn) Design of Transmission Shafting (Second Printing)
ASME B107.1 Socket Wrenches, Hand (Inch Series)
ASME B107.2 Socket Wrenches, Extensions, Adaptors, and Universal Joints, Power Drive (Impact) (Inch Series)
ASME B107.4M Driving and Spindle Ends for Portable Hand, Impact, Air, and Electric Tools (Percussion Tools Excluded)
ASME B107.5M Socket Wrenches, Hand (Metric Series)
ASME B107.6 Wrenches, Box, Angled, Open End, Combination, Flare Nut, and Tappet (Inch Series)
ASME B107.8M Adjustable Wrenches
ASME B107.9M Wrenches, Box, Angled, Open End, Combination, Flare Nut, and Tappet (Metric Series) Errata - 1996
ASME B107.10M Handles and Attachments for Hand Socket Wrenches - Inch and Metric Series
ASME B107.11M Pliers, Diagonal Cutting, and Nippers, End Cutting
ASME B107.12 Nut Drivers (Spin Type, Screwdriver Grip)(Inch Series)
ASME B107.13M Pliers - Long Nose, Long Reach
ASME B107.14M Hand Torque Tools
ASME B107.15 Flat Tip and Phillips Screwdrivers
ASME B107.16M Shears (Metal Cutting, Hand)
ASME B107.17M Gages, Wrench Openings, Reference
ASME B107.18M Pliers (Wire Twister)
ASME B107.19 Pliers, Retaining Ring
ASME B107.19
ASME B107.20M Pliers (Lineman's, Iron Worker's, Gas, Glass, Fence, and Battery)
ASME B107.21 Wrench, Crowfoot Attachments (Inch Series)
ASME B107.22M Electronic Cutters Errata - May 1999
ASME B107.23M Pliers, Multiple Position, Adjustable
ASME B107.25M Pliers - Performance Test Methods
ASME B107.27 Pliers, Multiple Position (Electrical Connector)
ASME B107.28M Electronic Torque Instruments
ASME B107.29M Electronic Tester, Hand Torque Tools
ASME B107.31M Screwdrivers, Cross Tip Gaging
ASME B107.34M Socket Wrenches for Spark Plugs
ASME B107.35M Nut Drivers (Spin Type, Screwdriver Grip)(Metric Series)
ASME B107.38M Electronic Pliers
ASME B107.41M Nail Hammers - Safety Requirements
ASME B107.42M Hatchets: Safety Requirements
ASME B107.43M Wood-Splitting Wedges: Safety Requirements
ASME B107.44M Glaziers' Chisels and Wood Chisels; Safety Requirements
ASME B107.45M Ripping Chisels and Flooring/Electricians' Chisels: Safety Requirements
ASME B107.46M Stud, Screw, and Pipe Extractors: Safety Requirements
ASME B107.47M Metal Chisels: Safety Requirements
ASME B107.48M Metal Punches and Drift Pins: Safety Requirements
ASME B107.49M Nail Sets: Safety Requirements
ASME B107.50M Brick Chisels and Brick Sets: Safety Requirements
ASME B107.53M Ball Peen Hammers: Safety Requirements
ASME B107.55M Axes: Safety Requirements
ASME B107.56 Body Repair Hammers and Dolly Blocks: Safety Requirements Formerly ANSI/HTI B173.5-1991
ASME B133.1M Gas Turbine Terminology R(1997)
ASME B133.2 Basic Gas Turbine R(1997)
ASME B133.2
ASME B133.3 Procurement Standard for Gas Turbine Auxiliary Equipment R(1994)
ASME B133.4 Gas Turbine Control and Protection Systems R(1997)
ASME B133.5 Procurement Standard for Gas Turbine Electrical Equipment R(1997)
ASME B133.6 Procurement Standard for Gas Turbine Ratings and Performance R(1994)
ASME B133.6
ASME B133.7M Gas Turbine Fuels Revision of ANSI B133.7-1977 R(1992)
ASME B133.8 Gas Turbine Installation Sound Emissions R(1989)
ASME B133.9 Measurement of Exhaust Emissions from Stationary Gas Turbine Engines Revision of ANSI B133.9-1979
ASME B133.10 Procurement Standard for Gas Turbine Information to Be Supplied by User and Manufacturer R(1994)
ASME B133.11 Procurement Standard for Gas Turbine Preparation for Shipping and Installation R(1994)
ASME B133.12 Procurement Standard for Gas Turbine Maintenance and Safety R(1994)
ASME B133.16 Procurement Standard for Gas Turbine Marine Applications
ASME BPE Bioprocessing Equipment
ASME CSD-1 Controls and Safety Devices for Automatically Fired Boilers
ASME CSD-1 INTERPRETATIONS Interpretations to CSD-1-1998 Controls and Safety Devices for Automatically Fired Boilers
ASME CSD-1A Addenda to CSD-1-1998 Controls and Safety Devices for Automatically Fired Boilers Errata - May 2000
ASME FAP-1 Quality Assurance Program Requirements for Fastener Manufacturers, Distributors, and Testing Laboratories
ASME HPS High Pressure Systems
ASME HPS-A Addenda to HPS-1994 High Pressure Systems
ASME HPS-B Addenda to HPS-1994 High Pressure Systems
ASME HST-1 Performance Standard for Electric Chain Hoists
ASME HST-2 Performance Standard for Hand Chain Manually Operated Chain Hoists
ASME HST-3 Performance Standard for Manually Lever Operated Chain Hoists
ASME HST-4 Performance Standard for Overhead Electric Wire Rope Hoists
ASME HST-5 Performance Standard for Air Chain Hoists
ASME HST-6 Performance Standard for Air Wire Rope Hoists
ASME MFC-1M Glossary of Terms Used in the Measurement of Fluid Flow in Pipes R(1997)
ASME MFC-2M Measurement Uncertainty for Fluid Flow in Closed Conduits R(1988)
ASME MFC-3M Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi Errata - September 1990 R(1995)
ASME MFC-4M Measurement of Gas Flow by Turbine Meters R(1997)
ASME MFC-5M Measurement of Liquid Flow in Closed Conduits Using Transit-Time Ultrasonic Flowmeters R(1994)
ASME MFC-6M Measurement of Fluid Flow in Pipes Using Vortex Flowmeters
ASME MFC-7M Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles R(1992)
ASME MFC-8M Fluid Flow in Closed Conduits - Connections for Pressure Signal Transmissions Between Primary and Secondary Devices
ASME MFC-9M Measurement of Liquid Flow in Closed Conduits by Weighing Methods Errata - December 1989
ASME MFC-10M Method for Establishing Installation Effects on Flowmeters
ASME MFC-10M (Pending) Method for Establishing Installation Effects on Flowmeters Comment Period Ends: 2000-09-26
ASME MFC-11M Measurement of Fluid Flow by Means of Coriolis Mass Flowmeters R(1994)
ASME MFC-14M Measurement of Fluid Flow Using Small Bore Precision Orifice Meters
ASME MFC-16M Measurement of Fluid Flow In Closed Conduits by Means of Electromagnetic Flowmeters
ASME MH1 Pallets, Slip Sheets, and Other Bases for Unit Loads Supersedes MH1.1.2, MH1.4.1M, MH1.6, and MH1.7M
ASME MH1.2.2M Pallet Sizes Revision of ANSI MH1.2.2-1975
ASME MH1.5M Slip Sheets
ASME MH1.8M Wood Pallets
ASME MH1.9 Export Pallets
ASME MH1A Addenda to MH1 - 1997 Pallets, Slip Sheets, and Other Bases for Unit Loads
ASME MH5.1.1M (Withdrawn) Requirements for Closed Van Cargo Containers Errata - October 1979, Errata - February 1980, Errata - March 1980, Errata - August 1981
ASME N278.1 Self-Operated and Power-Operated Safety-Related Valves Functional Specification Standard, Reactor Plants and Their Maintenance R(1992)
ASME N509 Nuclear Power Plant Air-Cleaning Units and Components Errata - July 1993 R(1996)
ASME N509 INTERPRETATIONS Interpretations to N509-1989 Nuclear Power Plant Air-Cleaning Units and Components
ASME N510 Testing of Nuclear Air Treatment Systems Errata - 1991 R(1995)
ASME N626.0 Qualifications and Duties for Authorized Inspection Agencies, Nuclear Inspectors, and Nuclear Inspector Supervisors
ASME N626.1 Qualifications and Duties for Authorized Inspection Agencies, Nuclear Inservice Inspectors, and Nuclear Inservice Inspector Supervisors
ASME N626.2 Qualifications and Duties for Authorized Inspection Agencies, Nuclear Inspectors (Concrete), and Nuclear Inspector Supervisors (Concrete)
ASME N626.3 Qualifications and Duties of Specialized Professional Engineers
ASME N626A Addenda to N626-1990 Qualifications and Duties for Authorized Nuclear Inspection Agencies and Personnel (Revised and Replaced by QAI-1)
ASME NOG-1 Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder)
ASME NOG-1A Addenda to NOG-1 Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder)
ASME NQA-1 1997 EDITION Quality Assurance Requirements for Nuclear Facility Applications
ASME NQA-1 2000 EDITION
ASME NQA-1A Addenda to NQA-1 - 1997 Edition Quality Assurance Requirements for Nuclear Facility Applications
ASME NQA-1A
ASME NQA TECH REPT Comparison of ASME NQA-1 and ISO 9001
ASME NUM-1 Rules for Construction of Cranes, Monorails, and Hoists (with Bridge or Trolley or Hoist of the Underhung Type)
ASME OHAI MARCH 2000 Organizations Holding Authorized Inspection Agency Certificates of Accreditation
ASME OHAI MARCH 2001
ASME OM CODE Code for Operation and Maintenance of Nuclear Power Plants
ASME OM CODE CASES Code Cases to OM CODE Code for Operation and Maintenance of Nuclear Power Plants
ASME OM CODE INTERPRETATIONS Interpretations to OM CODE-1998 Code for Operation and Maintenance of Nuclear Power Plants
ASME OMA CODE Addenda to OM Code - 1998 Code for Operation and Maintenance of Nuclear Power Plants
ASME OMA-S/G Addenda to OM-S/G - 1998 Standards and Guides for Operation and Maintenance of Nuclear Power Plants
ASME OMB-S/G Addenda to OM-S/G - 1997 Standards and Guides for Operation and Maintenance of Nuclear Power Plants
ASME PALD Safety Standard for Portable Automotive Lifting Devices
ASME PALD-A Addenda to PLAD-1997 Safety Standard for Portable Automotive Lifting Devices
ASME PALD INTERPRETATIONS Interpretations to PALD-1997 Safety Standard for Portable Automotive Lifting Devices
ASME PVHO-1 Safety Standard for Pressure Vessels for Human Occupancy
ASME PVHO-1 INTERPRETATIONS Interpretations to PVHO-1997 Safety Standard for Pressure Vessels for Human Occupancy
ASME PVHO-1 INTERPRETATIONS
ASME PVHO-1A Addenda to BPVH-1-1997 Safety Standard for Pressure Vessels for Human Occupancy
ASME QAI-1 Qualifications for Authorized Inspection Revision of N626-1990
ASME QAI-1 INTERPRETATIONS Interpretations to QAI-1-1995 Qualifications for Authorized Inspection
ASME QAI-1A Addenda to QAI-1-1995 Qualifications for Authorized Inspection
ASME QAI-1B Addenda to QAI-1-1995 Qualifications for Authorized Inspection
ASME QEI-1 Standard for the Qualification of Elevator Inspectors
ASME QEI-1
ASME QEI-1 (Pending) Standard for the Qualification of Elevator Inspectors Comment Period Ends: 2000-08-15
ASME QEI-1 INTERPRETATIONS Interpretations to ASME QEI-1-1997
ASME QEI-1A Addenda to AMSE QEI-1-1997 Standard for the Qualification of Elevator Inspectors
ASME QFO-1 Standard for the Qualification and Certification of Operators of High Capacity Fossil Fuel Fired Plants
ASME QHO-1 Qualification and Certification of Hazardous Waste Incinerator Operators
ASME QHO-1A Addenda to QHO-1 - 1994 Standard for the Qualification and Certification of Hazardous Waste Incinerator Operators
ASME QME-1 Qualification of Active Mechanical Equipment Used in Nuclear Power Plants
ASME QME-1A Addenda to QME-1 - 1997 Qualification of Active Mechanical Equipment Used in Nuclear Power Plants
ASME QMO-1 Qualification of Medical Waste Incinerator Operators
ASME QMO-1 (Pending) Qualification of Medical Waste Incinerator Operators Comment Period Ends: 2000-09-12
ASME QRO-1 Qualification and Certification of Resource Recovery Facility Operators
ASME QRO-1
ASME QRO-1A Addenda to QRO-1 - 1994 Standard for the Qualification and Certification of Resource Recovery Facility Operators
ASME QRO-1B Addenda to QRO-1 - 1994 Standard for the Qualification and Certification of Resource Recovery Facility Operators
ASME RTP-1 Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME RTP-1 INTERPRETATIONS Interpretations to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME RTP-1A Addenda to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME RTP-1B Addenda to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME RTP-1C Addenda to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME RTP-1D Addenda to RTP-1 - 1995 Edition Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME RTP-1E Addenda to RTP-1 - 1995 Edition Reinforced Thermoset Plastic Corrosion Resistant Equipment
ASME SI-1 Orientation and Guide for Use of SI (Metric) Units
ASME SPPE-1 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-1A Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-1B Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-1C Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-1D Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-2 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-2A Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-2B Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-2C Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME SPPE-2D Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations
ASME STS-1 Steel Stacks
ASME TDP-1 Recommended Practices for the Prevention of Water Damage to Steam Turbines Used for Electric Power Generation

huangyhg · 发表于 2009-4-26 14:37:44

目录（一）

ASME PCC-1 Guidelines for Pressure Boundary Bolted Flange Joint Assembly
ASME B107.52M Nail-Puller Bars: Safety Requirements
ASME B30.6 INTERPRETATIONS Interpretations to B30.6-1995 Derricks
ASME B30.17A Addenda to B30.17-1998 Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist)
ASME B40.200 Thermometers, Direct Reading and Remote Reading Incorporating ASME B40.3, B40.4, and B40.9; Replaces ASME B40.3:1997
ASME B18.8.100M Spring Pins: Coiled Type, Spring Pins: Slotted, Machine Dowel Pins: Hardened Ground, and Grooved Pins Metric Series; Incorporating ASME B18.8.3M, B18.8.4M, B18.8.5M, and B18.8.9M
ASME B56.1 INTERPRETATIONS Interpretations to B56.1-1993 Safety Standard for Low Lift and High Lift Trucks
ASME AG-1A Addenda to ASME AG-1-1997 Code on Nuclear Air and Gas Treatment
ASME B30.1A Addenda to B30.1-1998 Jacks
ASME PVHO-1B Addenda to Asme PVHO-1-1997 Safety Standard for Pressure Vessels for Human Occupancy
ASME B30.14C Addenda to B30.14-1996 Side Boom Tractors
ASME B94.18 Punches - Basic Ball-Lock, Light and Heavy Duty R(2000)
ASME NQA-1 INTERPRETATIONS Interpretations to NQA-1-2000 Edition Quality Assurance Requirements for Nuclear Facility Applications
ASME A112.6.2 Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks
ASME PTC 10 Performance Test Code on Compressors and Exhausters (Performance Test Codes)
ASME B18.30.1M Open-End Blind Rivets with Break Mandrels (Metric Series)
ASME B18.13A Addenda to B18.13-1996 Screw and Washer Assemblies - Sems (Inch Series)
ASME B107.51 Star Drills: Safety Requirements
ASME B30.6C Addenda to B30.6-1995 Derricks
ASME B30.14B Addenda to B30.14-1996 Side Boom Tractors
ASME BPEA Addenda to BPE-1997 Bioprocessing Equipment
ASME 3977-1 Gas Turbines: Procurement Part 1: General Introdustion and Definitions ISO 3977-1:1997
ASME 3977-2 Gas Turbines: Procurement Part 2: Standard Reference Conditions and Ratings ISO 3977-2: 1997
ASME AS-11 Personnel of Codes, Standards, and Related Conformity Assessment Committees
ASME B15.1 INTERPRETATION Interpretations to B15.1-2000 Safety Standard for Mechanical Power Transmission Apparatus
ASME B18.2.2 Square and Hex Nuts (Inch Series) R(1999)
ASME B18.2.3.8M Metric Hex Lag Screws R(1999)
ASME B18.2.3.8M
ASME B18.18.1M Inspection and Quality Assurance for General Purpose Fasteners R(1999)
ASME B18.18.2M Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners R(1999)
ASME B18.18.3M Inspection and Quality Assurance for Special Purpose Fasteners R(1999)
ASME B18.18.4M Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications R(1999)
ASME B18.22M Metric Plain Washers R(2000)
ASME B27.6 General Purpose Uniform Cross Section Spiral Retaining Rings R(1999)
ASME B27.7 General Purpose Tapered and Reduced Cross Section Retaining Rings R(1999)
ASME B30.19 Cableways
ASME B31.1B Addenda to B31.1-1998 Edition Power Piping
ASME B56.5 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles R(2000)
ASME B56.8 Safety Standard for Personnel and Burden Carriers R(2000)
ASME B56.9 Safety Standard for Operator Controlled Industrial Tow Tractors R(2000)
ASME B56.11.1 Double Race or Bi-Level Swivel and Rigid Industrial Casters Special Notice - October 1993 R(2000)
ASME B56.11.3 Load Handling Symbols for Powered Industrial Trucks Special Notice - October 1993 R(2000)
ASME B56.11.5 Measurements of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks Special Notice - October 1993 R(2000)
ASME B56.11.6 Evaluation of Visibility from Powered Industrial Trucks R(2000)
ASME B107.58M Riveting, Scaling, and Tinner's Setting Hammers: Safety Requirements
ASME B107.58M
ASME OM-S/G Standards and Guides for Operation and Maintenance of Nuclear Power Plants
ASME BPV DECEMBER-2000 Companies Holding Boiler and Pressure Vessel Certificates of Authorization for Use of Code Symbol Stamps and Testing Laboratories Holding Certificates of Acceptance for Conducting Tests of Pressure Relief Devices No.62-December 2000
ASME BPV APRIL-2001
ASME PTC 12.1 Closed Feedwater Heaters
ASME PTC 12.1
ASME SEC XI D1 ART IWE-5000 Article IWE-5000 System Pressure Tests
ASME SEC XI D1 ART IWE-7000 Article IWE-7000 Replacements DELETED
ASME A13.1 Scheme for the Identification of Piping Systems Erratum - September 1998
ASME A17.1 Safety Code for Elevators and Escalators
ASME A17.1
ASME A17.1 HDBK Handbook for Safety Code for Elevators and Escalators
ASME A17.1 INTERPRETATIONS Interpretations to A17.1-1996 Safety Code for Elevators and Escalators Includes Interpretations No. 1 through 22
ASME A17.1 INTERPRETATIONS
ASME A17.1A Addenda to A17.1-1996 Safety Code for Elevators and Escalators
ASME A17.1B Addenda to A17.1-1996 Safety Code for Elevators and Escalators
ASME A17.1C Addenda to A17.1 - 1996 Safety Code for Elevators and Escalators
ASME A17.1D Addenda to Asme A17.1-1996 Safety Code for Elevators and Escalators
ASME A17.2.1 Inspectors' Manual for Electric Elevators
ASME A17.2.1A Addenda to A17.2.1-1996 Inspectors' Manual for Electric Elevators
ASME A17.2.1B Addenda to A17.2.1-1996 Inspectors' Manual for Electric Elevators
ASME A17.2.2 Inspectors' Manual for Hydraulic Elevators
ASME A17.2.2A Addenda to A17.2.2-1997 Inspectors' Manual for Hydraulic Elevators
ASME A17.2.3 Inspectors' Manual for Escalators and Moving Walks Includes Inspection Procedures for Escalators and Moving Walks
ASME A17.2.3 INT NO 1 Interpretations No. 1 to A17.2.3-1998 Inspectors- Manual for Escalators and Moving Walks
ASME A17.2.3A Addenda to ASME A17.2.3-1998 Inspectors' Manual for Escalators and Moving Walks
ASME A17.3 Safety Code for Existing Elevators and Escalators
ASME A17.3 INTERPRETATIONS Interpretations to A17.3-1996 Safety Code for Existing Elevators and Escalators Includes Interpretations No. 1 Through 4
ASME A17.3A Addenda to ASME A17.3-1996 Safety Code for Existing Elevators and Escalators
ASME A17.4 Guide for Emergency Personnel (Includes Evacuation Procedures and Firefighters' Service Operating Procedures)
ASME A17.5 Elevator and Escalator Electrical Equipment CAN/CSA-B44.1-1996
ASME A18.1 Safety Standard for Platform Lifts and Stairway Chairlifts Special Notice - 1999
ASME A90.1 Safety Standard for Belt Manlifts
ASME A90.1 INTERPRETATIONS Interpretations to ASME A90.1-1997
ASME A90.1A Addenda to ASME A90.1-1997 Safety Standard for Belt Manlifts
ASME A90.1B (Pending) Addenda to ASME A90.1-1997 Safety Standard for Belt Manlifts Comment Period Ends: 2000-09-12
ASME A112.1.2 Air Gaps in Plumbing Systems R(1998)
ASME A112.1.3 Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances
ASME A112.3.1 Performance Standard and Installation Procedures for Stainless Steel Drainage Systems for Sanitary, Storm, and Chemical Applications, Above and Below Ground
ASME A112.3.4 Macerating Toilet Systems and Related Components
ASME A112.4.1 Water Heater Relief Valve Drain Tubes R(1998)
ASME A112.4.3 Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System
ASME A112.6.1M Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use
ASME A112.6.7 (Pending) Enameled and Epoxy Coated Cast Iron and PVC Platic Sanitary Floor Sinks Comment Period Ends: 2000-09-26
ASME A112.14.1 Backwater Valves R(1998)
ASME A112.18.1 Plumbing Fixture Fittings
ASME A112.18.3 (Pending) Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings Comment Period Ends: 2000-09-26
ASME A112.18.3M Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings
ASME A112.18.6 Flexible Water Connectors
ASME A112.18.7 Deck Mounted Bath/Shower Transfer Valves with Integral Backflow Protection
ASME A112.19.1M Enameled Cast Iron Plumbing Fixtures Errata - November 1996; Supplement 2 - June 2000 R(1999)
ASME A112.19.2M Vitreous China Plumbing Fixtures Supplement 1 - June 2000
ASME A112.19.3M Stainless Steel Plumbing Fixtures (Designed for Residential Use) Revision of ANSI A112.19.3-1976 R(1996)
ASME A112.19.3
ASME A112.19.4M Porcelain Enameled Formed Steel Plumbing Fixtures Errata - November 1996; Supplement 1 - 1998; Supplement 2 - June 2000 R(1999)
ASME A112.19.5 Trim for Water-Closet Bowls, Tanks, and Urinals
ASME A112.19.6 Hydraulic Performance Requirements for Water Closets and Urinals
ASME A112.19.7M Whirlpool Bathtub Appliances
ASME A112.19.8M Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, Hot Tubs, and Whirlpool Bathtub Appliances R(1996)
ASME A112.19.9M Non-Vitreous Ceramic Plumbing Fixtures R(1998)
ASME A112.19.10 Dual Flush Devices for Water Closets
ASME A112.19.12 Wall Mounted and Pedestal Mounted, Adjustable and Pivoting Lavatory and Sink Carrier Systems Comment Period Ends: 2000-08-15
ASME A112.19.14 (Pending) Six Liter Closets Equipped with Dual Flushing Device Comment Period Ends: 2000-09-12
ASME A112.21.1M Floor Drains R(1998)
ASME A112.21.2M Roof Drains Revision of ANSI A112.21.2-1971
ASME A112.21.3M Hydrants for Utility and Maintenance Use Revision of ANSI A112.21.3-1976 R(1995)
ASME A112.36.2M Cleanouts R(1998)
ASME A120.1 Safety Requirements for Powered Platforms for Building Maintenance
ASME A120.1A Addenda to A120.1-1996 Safety Requirements for Powered Platforms for Building Maintenance
ASME A120.1B Addenda to ASME A120.1-1996 Safety Requirements for Powered Platforms for Building Maintenance
ASME AG-1 Code on Nuclear Air and Gas Treatment
ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
ASME B1.1 (Pending) Unified Inch Screw Threads (UN and UNR Thread Form)
ASME B1.2 Gages and Gaging for Unified Inch Screw Threads Errata May 1992 R(1991)
ASME B1.3M Screw Thread Gaging Systems for Dimensional Acceptability - Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ) Errata - 1994
ASME B1.5 Acme Screw Threads
ASME B1.7M Nomenclature, Definitions, and Letter Symbols for Screw Threads Revision of ANSI B1.7-1977 R(1992)
ASME B1.8 Stub Acme Screw Threads R(1994)
ASME B1.9 Buttress Inch Screw Threads 7 Degrees/45 Degrees Form with 0.6 Pitch Basic Height of Thread Engagement R(1992)
ASME B1.10M Unified Miniature Screw Threads Errata - January 1998
ASME B1.11 Microscope Objective Thread Errata - July 1972 R(1994)
ASME B1.12 Class 5 Interference-Fit Thread R(1998)
ASME B1.13M Metric Screw Threads - M Profile
ASME B1.15 Unified Inch Screw Threads (UNJ Thread Form) Errata - March 1997
ASME B1.16M Gages and Gaging for Metric M Screw Threads Revision of ANSI B1.16-1972 R(1992)
ASME B1.20.1 Pipe Threads, General Purpose (Inch) Revision and Redesignation of ASME/ANSI B2.1-1968 R(1992)
ASME B1.20.3 Dryseal Pipe Threads (Inch) Revision and Redesignation of B2.2-1968 R(1998)
ASME B1.20.5 Gaging for Dryseal Pipe Threads (Inch) R(1998)
ASME B1.20.7 Hose Coupling Screw Threads (Inch) R(1998)
ASME B1.21M Metric Screw Threads: MJ Profile
ASME B1.22M Gages and Gaging for MJ Series Metric Screw Threads Revision of ANSI B1.22-1978 R(1992)
ASME B1.30M Screw Threads - Standard Practice for Calculating and Rounding Dimensions
ASME B1 TECH REPT Measurement Uncertainty for 60 Deg. Screw Thread Gage Element Measurement (Inch and Metric)
ASME B4.1 Preferred Limits and Fits for Cylindrical Parts R(1999)
ASME B4.2 Preferred Metric Limits and Fits R(1999)
ASME B4.3 General Tolerances for Metric Dimensioned Products R(1999)
ASME B5.1M T-Slots, Their Bolts, Nuts, and Tongues Revision of ANSI B5.1-1975; Should Be Used Instead of ANSI B5.1. Which Was Cancelled in 1985
ASME B5.1M
ASME B5.5 Rotating Air Cylinders and Adapters One of a Series of Standards for Small Tools and Machine Tool Elements R(1998)
ASME B5.8 Chucks and Chuck Jaws R(1994)
ASME B5.8 (Pending) Chucks and Chuck Jaws Comment Period Ends: 2000-09-12
ASME B5.9 Spindle Noses for Tool Room Lathes, Engine Lathes, Turret Lathes, and Automatic Lathes R(1998)
ASME B5.10 Machine Tapers
ASME B5.11 Spindle Noses and Adjustable Adapters for Multiple Spindle Drilling Heads One of a Series of Standards for Small Tools and Machine Tool Elements R(1994)
ASME B5.16 Accuracy of Engine and Tool Room Lathes One of a Series of Standards for Small Tools and Machine Tool Elements R(1992)
ASME B5.18 Spindle Noses and Tool Shanks for Milling Machines R(1998)
ASME B5.25 Punch and Die Sets R(1992)
ASME B5.25M Punch and Die Sets (Metric) R(1992)
ASME B5.28 Mounting Dimensions of Lubricating and Coolant Pumps for Machine Tools R(1994)
ASME B5.32 Grinding Machines, Surface, Reciprocating Table - Horizontal Spindle R(1994)
ASME B5.32.1 Grinding Machines, Surface, Reciprocating Table - Vertical Spindle R(1994)
ASME B5.33 External Cylindrical Grinding Machines - Plain R(1994)
ASME B5.35 Machine Mounting Specifications for Abrasive Discs and Plate Mounted Wheels Errata - October 1985 R(1994)
ASME B5.37 External Cylindrical Grinding Machines - Centerless R(1994)
ASME B5.40 Spindle Noses and Tool Shanks for Horizontal Boring Machines R(1991)
ASME B5.42 External Cylindrical Grinding Machines - Universal R(1994)
ASME B5.43 Modular Machine Tool Standards R(1994)
ASME B5.43M Modular Machine Tool Standards (Metric) R(1994)
ASME B5.44 Rotary Table Surface Grinding Machines R(1998)
ASME B5.45 Milling Machines R(1998)
ASME B5.46 Symbols for Machine Tool Indicator Plates R(1994)
ASME B5.47 Milling Machine Arbor Assemblies R(1991)
ASME B5.48 Ball Screws Errata - March 1979 R(1994)
ASME B5.49 Glossary of Power Press Terms
ASME B5.50 "V" Flange Tool Shanks for Machining Centers with Automatic Tool Changers Errata - February 1995
ASME B5.51M Preferred SI Units for Machine Tools R(1994)
ASME B5.52M Mechanical Power Presses General Purpose Single Point, GAP Type (Metric) R(1994)
ASME B5.53M Cutter and Tool Grinding Machines R(1994)
ASME B5.54 Methods for Performance Evaluation of Computer Numerically Controlled Machining Centers Errata - 1993 R(1998)
ASME B5.55M Specification and Performance Standard, Power Press Brakes
ASME B5.56M Specification and Performance Standard, Power Shears
ASME B5.57 Methods for Performance Evaluation of Computer Numerically Controlled Lathes and Turning Centers
ASME B15.1 Safety Standard for Mechanical Power Transmission Apparatus
ASME B16.1 Cast Iron Pipe Flanges and Flanged Fittings Classes 25, 125, and 250
ASME B16.3 Malleable Iron Threaded Fittings Classes 150 and 300
ASME B16.4 Gray Iron Threaded Fittings - Classes 125 and 250
ASME B16.4 INTERPRETATIONS Interpretations to B16.4-1998 - Gray Iron Threaded Fittings - Classes 125 and 250
ASME B16.5 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24
ASME B16.5 INTERPRETATIONS Interpretations to B16.5-1996 Pipe Flanges and Flanged Fittings Includes Interpretation No. 3
ASME B16.5A Addenda to B16.5-1996 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24
ASME B16.9 Factory-Made Wrought Steel Buttwelding Fittings
ASME B16.9 INTERPRETATIONS Interpretations to B16.9-1993 Factory-Made Wrought Steel Buttwelding Fittings Includes Interpretation No. 1
ASME B16.10 Face-to-Face and End-to-End Dimensions of Valves
ASME B16.10 INTERPRETATIONS Interpretations to B16.10-1992 Face-to-Face and End-to-End Dimensions of Valves Includes Interpretation No. 1
ASME B16.11 Forged Fittings, Socket-Welding and Threaded
ASME B16.12 Cast Iron Threaded Drainage Fittings
ASME B16.14 Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads
ASME B16.15 Cast Bronze Threaded Fittings Classes 125 and 250 R(1994)
ASME B16.15 INTERPRETATIONS Interpretations to B16.5-1985 Cast Bronze Threaded Fittings Classes 125 and 250 Includes Interpretations No. 1
ASME B16.18 Cast Copper Alloy Solder Joint Pressure Fittings R(1994)
ASME B16.20 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound, and Jacketed
ASME B16.20A Addenda to B16.20-1998 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound, and Jacketed
ASME B16.20B Addenda to B16.20-1993 Metallic Gaskets for Pipe Flanges - Ring-Joint, Spiral-Wound, and Jacketed
ASME B16.21 Nonmetallic Flat Gaskets for Pipe Flanges Revision of ANSI B16.21-1978
ASME B16.22 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
ASME B16.22A Addenda to B16.22-1995 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
ASME B16.23 Cast Copper Alloy Solder Joint Drainage Fittings - DWV Errata - January 1994
ASME B16.24 Cast Copper Alloy Pipe Flanges and Flanged Fittings Class 150, 300, 400, 600, 900, 1500, and 2500 Errata - 1991 R(1998)
ASME B16.25 Buttwelding Ends
ASME B16.25 INTERPRETATIONS Interpretations to B16.25-1997 Buttwelding Ends Includes Interpretation No. 1
ASME B16.26 Cast Copper Alloy Fittings for Flared Copper Tubes
ASME B16.28 Wrought Steel Buttwelding Short Radius Elbows and Returns
ASME B16.28 INTERPRETATIONS Interpretations to B16.28-1994 Wrought Steel Buttwelding Short Radius Elbows and Returns Includes Interpretations No. 1
ASME B16.29 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV
ASME B16.33 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes 1/2 Through 2)
ASME B16.34 Valves - Flanged, Threaded, and Welding End
ASME B16.34 INTERPRETATIONS Interpretations to B16.34-1996 Valves - Flanged, Threaded, and Welding End Includes Interpretation No. 2
ASME B16.34A Addenda to B16.34-1996 Valves - Flanged, Threaded, and Welding End
ASME B16.36 Orifice Flanges
ASME B16.36 INTERPRETATIONS Interpretations to B16.36-1996 Orifice Flanges
ASME B16.38 Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2 1/2 to 12, 125 psig Maximum) R(1994)
ASME B16.39 Malleable Iron Threaded Pipe Unions Classes 150, 250, and 300
ASME B16.40 Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems R(1994)
ASME B16.41 Functional Qualification Requirements for Power Operated Active Valve Assemblies for Nuclear Power Plants R(1989)
ASME B16.41
ASME B16.42 Ductile Iron Pipe Flanges and Flanged Fittings Classes 150 and 300
ASME B16.43 (Withdrawn) Wrought Copper and Copper Alloy Solder Joint Fittings for Sovent Drainage Systems
ASME B16.44 Manually Operated Metallic Gas Valves for Use in House Piping Systems
ASME B16.44A Addenda to B16.44-1995 Manually Operated Metallic Gas Valves for Use in House Piping Systems
ASME B16.45 Cast Iron Fittings for Sovent Drainage Systems
ASME B16.47 Large Diameter Steel Flanges NPS 26 Through NPS 60
ASME B16.47 INTERPRETATIONS Interpretations to B16.47-1996 Large Diameter Steel Flanges NPS 26 Through NPS 60
ASME B16.47A Addenda to B16.47-1990 Large Diameter Steel Flanges NPS 26 Through NPS 60
ASME B16.48 Steel Line Blanks
ASME B16.49 Factory-Made Wrought Steel Buttwelding Induction Bends for Transportation and Distribution Systems
ASME B17.1 Keys and Keyseats R(1998)
ASME B17.2 Woodruff Keys and Keyseats Revision of USAS B17F-1930 R(1998)
ASME B18.1.1 Small Solid Rivets 7/16 Inch Nominal Diameter and Smaller Revision of B18.1-1965 R(1995)
ASME B18.1.2 Large Rivets 1/2 Inch Nominal Diameter and Larger Revision of B18.4-1960 R(1995)
ASME B18.1.3M Metric Small Solid Rivets 12 mm Nominal Diameter and Smaller Errata - October 1985 R(1995)
ASME B18.2.1 Square and Hex Bolts and Screws (Inch Series)
ASME B18.2.1A Addenda to ASME B18.2.1-1996 Square and Hex Bolts and Screws (Inch Series)
ASME B18.2.3.1M Metric Hex Cap Screws
ASME B18.2.3.2M Metric Formed Hex Screws Errata - December 1980 R(1995)
ASME B18.2.3.3M Metric Heavy Hex Screws Errata - April 1981 R(1995)
ASME B18.2.3.4M Metric Hex Flange Screws R(1995)
ASME B18.2.3.5M Metric Hex Bolts Errata - May 1981 R(1995)
ASME B18.2.3.6M Metric Heavy Hex Bolts Errata - April 1981 R(1995)
ASME B18.2.3.7M Metric Heavy Hex Structural Bolts Errata - April 1981 R(1995)
ASME B18.2.3.9M Metric Heavy Hex Flange Screws R(1995)
ASME B18.2.3.10M Square Head Bolts (Metric Series)
ASME B18.2.4.1M Metric Hex Nuts, Style 1 Errata - May 1981 R(1995)
ASME B18.2.4.2M Metric Hex Nuts, Style 2 Errata - January 1982 R(1995)
ASME B18.2.4.3M Metric Slotted Hex Nuts Errata - May 1981 R(1995)
ASME B18.2.4.4M Metric Hex Flange Nuts R(1993)
ASME B18.2.4.4M
ASME B18.2.4.5M Metric Hex Jam Nuts Errata - May 1981 R(1998)
ASME B18.2.4.6M Metric Heavy Hex Nuts Errata - April 1981 R(1998)
ASME B18.2.6 Fasteners for Use in Structural Applications
ASME B18.2.8 Clearance Holes for Bolts, Screws, and Studs
ASME B18.3 Socket Cap, Shoulder, and Set Screws, Hex and Spline Keys (Inch Series)
ASME B18.3.1M Socket Head Cap Screws (Metric Series) R(1993)
ASME B18.3.2M Metric Series Hexagon Keys and Bits R(1998)
ASME B18.3.3M Hexagon Socket Head Shoulder Screws (Metric Series) R(1993)
ASME B18.3.4M Hexagon Socket Button Head Cap Screws (Metric Series) R(1993)
ASME B18.3.5M Hexagon Socket Flat Countersunk Head Cap Screws (Metric Series) R(1993)
ASME B18.3.6M Metric Series Socket Set Screws R(1993)
ASME B18.5 Round Head Bolts (Inch Series) R(1998)
ASME B18.5.2.1M Metric Round Head Short Square Neck Bolts
ASME B18.5.2.2M Metric Round Head Square Neck Bolts R(1993)
ASME B18.5.2.2M
ASME B18.5.2.3M Round Head Square Neck Bolts with Large Head (Metric Series) R(1998)
ASME B18.6.1 Wood Screws (Inch Series) R(1997)
ASME B18.6.2 Slotted Head Cap Screws, Square Head Set Screws, and Slotted Headless Set Screws (Inch Series)
ASME B18.6.3 Machine Screws and Machine Screw Nuts
ASME B18.6.4 Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws (Inch Series)
ASME B18.6.5M Metric Thread-Forming and Thread-Cutting Tapping Screws 2000 Edition; Revision of ANSI/ASME B18.6.5M-1986(R1993)
ASME B18.6.7M Metric Machine Screws 2000 Edition; Revision of ASME B18.6.7M-1985(1993)
ASME B18.7 General Purpose Semi-Tubular Rivets, Full Tubular Rivets, Split Rivets and Rivet Caps R(1992)
ASME B18.7.1M Metric General Purpose Semi-Tubular Rivets R(1992)
ASME B18.7.1M
ASME B18.8.1 Clevis Pins and Cotter Pins (Inch Series) Errata - April 1995
ASME B18.8.1
ASME B18.8.2 Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins (Inch Series)
ASME B18.8.3M Spring Pins - Coiled Type (Metric Series)
ASME B18.8.4M Spring Pins - Slotted (Metric Series)
ASME B18.8.5M Machine Dowel Pins - Hardened Ground (Metric Series)
ASME B18.8.6M Cotter Pins (Metric Series)
ASME B18.8.6M
ASME B18.8.7M Headless Clevis Pins (Metric Series)
ASME B18.8.7M
ASME B18.8.8M Headed Clevis Pins (Metric Series)
ASME B18.8.8M
ASME B18.8.9M Grooved Pins (Metric Series)
ASME B18.8.200M Cotter Pins, Headless Clevis Pins, and Headed Clevis Pins Metric Series
ASME B18.9 Plow Bolts (Inch Series)
ASME B18.10 Track Bolts and Nuts R(1992)
ASME B18.10
ASME B18.11 Miniature Screws R(1992)
ASME B18.12 Glossary of Terms for Mechanical Fasteners R(1991)
ASME B18.13 Screw and Washer Assemblies - Sems (Inch Series)
ASME B18.13.1M Screw and Washer Assemblies - Sems (Metric Series)
ASME B18.15 Forged Eyebolts R(1995)
ASME B18.15M Metric Lifting Eyes Incorporating ASME B18.15.1M-1998 and ASME B18.15.2M-1998
ASME B18.16.1M Mechanical and Performance Requirements for Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts Errata - December 1980 R(1995)
ASME B18.16.2M Torque-Tension Test Requirements for Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts R(1995)
ASME B18.16.3M Dimensional Requirements for Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts
ASME B18.18.2M SUPPLEMENT Supplement of ASME B18.18.2m-1987 Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners
ASME B18.18.5M Inspection and Quality Assurance Plan Requiring In-Process Inspection and Controls
ASME B18.18.6M Quality Assurance Plan for Fasteners Produced in a Third Party Accreditation System
ASME B18.18.7M Quality Assurance Plan for Fasteners Produced in a Customer Approved Control Plan
ASME B18.21.1 Lock Washers (Inch Series)
ASME B18.21.2M Lock Washers (Metric Series)
ASME B18.22.1 Plain Washers Reaffirmation and Redesignation of ASA B27.2-1965 R(1998)
ASME B18.22.1
ASME B18.23.1 (Withdrawn) Beveled Washers Reaffirmation and Redesignation of USAS B27.4-1967 R(1975)
ASME B18.24.1 Part Identifying Number (PIN) Code System Standard for B18 Externally Threaded Products
ASME B18.24.2 Part Identifying Number (PIN) Code System Standard for B18 Internally Threaded Products
ASME B18.24.3 Part Identifying Number (PIN) Code System Standard for B18 Nonthreaded Products
ASME B18.25.1M Square and Rectangular Keys and Keyways
ASME B18.25.2M Woodruff Keys and Keyways
ASME B18.25.3M Square and Rectangular Keys and Keyways: Width Tolerances and Deviations Greater than Basic Size
ASME B18.27 Tapered and Reduced Cross Section Retaining Rings (Inch Series) Incorporating ASME B18.27.1, B18.27.2, B18.27.3, B18.27.4, and B18.27.5
ASME B18.27A Addenda to ASME B18.27-1998 Tapered and Reduced Cross Section Retaining Rings (Inch Series)
ASME B18.27B Addenda to ASME B18.27-1998 Tapered and Reduced Cross Section Retaining Rings (Inch Series)
ASME B18.29.1 Helical Coil Screw Thread Inserts - Free Running and Screw Locking (Inch Series) Errata - August 1995
ASME B19.1 Safety Standard for Air Compressor Systems
ASME B19.3 Safety Standard for Compressors for Process Industries
ASME B19.3A Addenda to B19.3-1991 Safety Standard for Compressors for Process Industries
ASME B19.3B Addenda to B19.3-1991 Safety Standard for Compressors for Process Industries
ASME B20.1 Safety Standard for Conveyors and Related Equipment

huangyhg · 发表于 2009-4-26 14:38:35

1       ASME TDP-1-2006 发电站用防护水渍蒸汽涡轮机的推荐实施规程..[2006/01]
2       ASME PTC 29-2005 液压汽轮发电机组的速度调节系统[2005/01]
3       ASME PTC 39-2005 蒸汽疏水阀[2005/01]
4       ASME PTC 22-2005 燃气涡轮机的性能试验规则[2005/01]
5       ASME PTC 6.2-2004 组合循环中蒸汽涡轮机[2004/01]
6       ASME PTC 6-2004 蒸汽轮机[2004/01]
7       ASME Y14.41-2003 数字化产品定义数据实施规程[2003/01]
8       ASME OM-S/G-2000 核电厂运行和维护的标准和指导[2000/12]
9       ASME A17.1D-2000 电梯和电动扶梯的AsmeA17.1-1996安全编码的..[2000/11]
10       ASME A17.2.3A-2000 电梯和移动人行道检查员手册的ASME A17.2.3..[2000/08]
11       ASME SEC II B NMA APP A-2000 附录A - 非强制接受ASTM版本[2000/07]
12       ASME SEC II C SFA-5.3-2000 SFA-5.3 用于遮蔽金属弧焊的铝和铝合金电极..[2000/07]
13       ASME SEC II C SFA-5.29-2000 SFA-5.29 用于以助焊剂为核心的弧焊的低合金..[2000/07]
14       ASME SEC II D SB PT 1-2000 子部分 1 压力表[2000/07]
15       ASME SEC II D SB PT 2-2000 子部分 2 物理特性表[2000/07]
16       ASME SEC II D APPENDIX 6-2000 附录6 冶金学现象[2000/07]
17       ASME SEC III NCA-9000-2000 第NCA-9000条术语表[2000/07]
18       ASME SEC III D1 NH A2000-2000 2000 附录变化的总结[2000/07]
19       ASME SEC III D1 ND A2000-2000 2000 附录变化的总结[2000/07]
20       ASME SEC III D1 NE A2000-2000 2000 附录变化和总结[2000/07]
21       ASME SEC III D1 NF A2000-2000 2000 附录变化的总结[2000/07]
22       ASME SEC III D1 APP A2000-2000 2000 附录变化的总结[2000/07]
23       ASME SEC III D1 NC A2000-2000 2000 附录变化的总结[2000/07]
24       ASME SEC III D1 NG A2000-2000 2000 附录变化的总结[2000/07]
25       ASME SEC III D1 NB A2000-2000 2000 附录变化的总结[2000/07]
26       ASME SEC III D3 WA-5000-2000 第WA-5000条授权检查[2000/07]
27       ASME SEC V A-2-2000 第2条 X光线照相术检查[2000/07]
28       ASME SEC V A-4-2000 第4条业务中检查的超声检查方法[2000/07]
29       ASME SEC V A-5-2000 第5条材料和构造的超声检查方法[2000/07]
30       ASME SEC V A-6-2000 第6条液体渗透检查[2000/07]
31       ASME SEC V A-7-2000 第7章磁性粒子检查[2000/07]
32       ASME SEC V B SE-94-2000 SE-94 X光照相术测试的标准指导 ASTM E 94-93[2000/07]
33       ASME SEC V B SE-1025-2000 SE-1025 用于放射线学的孔型图象质量指示器..[2000/07]
34       ASME SEC V B SE-1255-2000 SE-1255 放射线透视的标准惯例 ASTM E 1255-96[2000/07]
35       ASME SEC V B SA-388/SA-388M-2000 SA-388/SA-388M 重钢锻造的超声检查标准惯例..[2000/07]
36       ASME SEC V B SA-435/SA-435M-2000 SA-435/SA-435M 钢盘的直束超声检查的标准规..[2000/07]
37       ASME SEC V B SA-577/SA-577M-2000 SA-577/SA-577M 钢盘的角度束超声检查的标准..[2000/07]
38       ASME SEC V B SA-578/SA-578M-2000 SA-578/SA-578M 有特殊应用的平面和敷钢板的..[2000/07]
39       ASME SEC V B SA-609/SA-609M-2000 SA-609/SA-609M 铸件，碳，低合金，和马氏..[2000/07]
40       ASME SEC V B SA-745/SA-745M-2000 SA-745/SA-745M 奥氏钢锻造的超声检查的标准..[2000/07]
41       ASME SEC V B SB-509-2000 SB-509 用于核应用的镍合金板的补充要求规范..[2000/07]
42       ASME SEC V B SB-510-2000 SB-510 用于核应用的镍合金杆和棒的补充要求..[2000/07]
43       ASME SEC V B SB-513-2000 SB-513 用于核应用的镍合金无缝管道的补充要..[2000/07]
44       ASME SEC V B SE-114-2000 SE-114 采用接触方法的超声脉冲回声直束检查..[2000/07]
45       ASME SEC V B SE-273-2000 SE-273 纵向焊接管的超声检查的标准惯例 AS..[2000/07]
46       ASME SEC V B SE-215-2000 SE-215 用于无缝铝合金管的电磁测试的标准设..[2000/07]
47       ASME SEC V B SE-243-2000 SE-243 铜和铜合金管的电磁（涡流）检查的标..[2000/07]
48       ASME SEC V B SE-650-2000 SE-650 安装压电声音散发传感器的标准指导 ..[2000/07]
49       ASME SEC V B SE-976-2000 SE-976 决定声音散发传感器响应的重复性的标..[2000/07]
50       ASME SEC V B SE-1316-2000 SE-1316 非破坏性检查的标准术语 ASTM E 13..[2000/07]
51       ASME SEC VIII D1 A PT UG-2000 UG 部分所有建筑方法和所有材料的一般要求[2000/07]
52       ASME PALD-A-2000 便携式汽车提升装置的安全标准 PLAD-1997的..[2000/05]
53       ASME A17.1 INTERPRETATIONS 电梯和自动扶梯包括解释1到22的A17.1-1996安..[2000/01]
54       ASME B31.1 CASES NO. 25 电力管道系统 B31.1的25号案例[2000/01]
55       ASME B31.1 CASES NO. 26 电力管道系统 B31.1的26号案例[2000/01]
56       ASME B31.1 INTERPRETATIONS 电力管道B31.1-1998的解释，包括31号解释[2000/01]
57       ASME N509 INTERPRETATIONS 核电厂空气清洁装置和元件 N509-1989的解释[2000/01]
58       ASME OM CODE INTERPRETATIONS 核电厂的运行和维护用OM CODE代码的解释[2000/01]
59       ASME PALD INTERPRETATIONS 便携式汽车提升装置的安全标准 PALD-1997的..[2000/01]
60       ASME A17.3 INTERPRETATIONS 现有的电梯和电动扶梯包括1到4号解释的A17...[2000/01]
61       ASME B15.1 INTERPRETATION 机械电力传输装置的B15.1-2000安全标准的解释[2000/01]
62       ASME B31.1B-2000 电力管道 B31.1-1998的附录[2000/01]
63       ASME A17.3A-2000 现有电梯和电动扶梯的ASME A17.3-1996安全编..[2000/01]
64       ASME B15.1-2000 机械电力传输装置的安全标准[2000/01]
65       ASME B31.1A-1999 电力管道 B31.1-1998的附录[1999/11]
66       ASME PTC 1-1999 一般指导（性能测试码）[1999/11]
67       ASME HST-6-1999 空中电线绳索提升装置的性能标准[1999/11]
68       ASME HST-4-1999 架空电线绳索提升装置的性能标准[1999/11]
69       ASME HST-1-1999 电动链条提升装置的性能标准[1999/11]
70       ASME QEI-1A-1999 电梯检查员的资格标准 AMSE QEI-1-1997的附录[1999/10]
71       ASME OMB-S/G-1999 OM-S/G的附录-1997 核电厂运行和维护的标准..[1999/09]
72       ASME SEC VII ADD-1999 BPVC VII部分 1999 附录非合并电力锅炉（锅..[1999/07]
73       ASME SEC I ADD-1999 BPVC I 部分 1999 附录，电力锅炉的建筑规..[1999/07]
74       ASME SEC II-C ADD-1999 BPVC II部分 1999 附录，材料C部分-焊接杆..[1999/07]
75       ASME SEC III NCA ADD-1999 BPVC 3部分 1999 附录，核设施元件的建设原..[1999/07]
76       ASME SEC III D1 NB ADD-1999 BPVC 3部分 1999 附录，核设施元件的建设规..[1999/07]
77       ASME SEC III D1 NC ADD-1999 BPVC 3部分，1999 附录核设施元件的建设规..[1999/07]
78       ASME SEC III D1 ND ADD-1999 BPVC 3部分，1999 附录，核设施元件的建设..[1999/07]
79       ASME SEC III D1 NE ADD-1999 BPVC 3部分1999附录，核设施元件的建设规则..[1999/07]
80       ASME SEC III D1 NF ADD-1999 BPVC 3部分1999附录，核设施元件的建设规则..[1999/07]
81       ASME SEC III D1 NG ADD-1999 BPVC 3部分，核设施元件的建设规则第1节-N..[1999/07]
82       ASME SEC III D1 NH ADD-1999 BPVC 3部分 1999 附录，核设施元件的建设规..[1999/07]
83       ASME SEC III D2 ADD-1999 BPVC 3部分 1999 附录，核设施元件的建筑规..[1999/07]
84       ASME SEC III D3 ADD-1999 BPVC III部分1999附录，核设施元件的建设规..[1999/07]
85       ASME SEC I PT PEB-1999 电动锅炉的PEB部分要求[1999/07]
86       ASME SEC VIII D2 ART T-3-1999 第 T-3 条流体静力学测试[1999/07]
87       ASME SEC VIII D2 ART T-4-1999 第T-4条风力测试[1999/07]
88       ASME SEC II C SFA-5.11-1999 SFA-5.11 用于遮蔽金属弧焊的镍和镍合金焊..[1999/07]
89       ASME SEC II C SFA-5.12-1999 SFA-5.12 用于弧焊和切断的钨和钨合金电极..[1999/07]
90       ASME SEC II C SFA-5.14-1999 SFA-5.14 镍和镍合金裸焊接电极和杆规范 AW..[1999/07]
91       ASME SEC II C SFA-5.17-1999 SFA-5.17 用于浸没弧焊的碳钢电极和助焊剂的..[1999/07]
92       ASME SEC II C SFA-5.20-1999 SFA-5.20 用于助焊剂核心弧焊的碳钢电极规范..[1999/07]
93       ASME SEC II C SFA-5.23-1999 SFA-5.23 用于低合金钢电极的规范和用于浸没..[1999/07]
94       ASME SEC II C SFA-5.25-1999 SFA-5.25 碳和低合金钢电极规范，和电渣焊接..[1999/07]
95       ASME SEC II C SFA-5.26-1999 SFA-5.26 用于电气焊接的碳和低合金钢电极的..[1999/07]
96       ASME SEC II C SFA-5.28-1999 SFA-5.28 用于气体遮蔽电弧焊的低合金钢电极..[1999/07]
97       ASME SEC III D1 NB A99-1999 1999 附录变化的总结[1999/07]
98       ASME SEC III D1 NC A99-1999 1999 附录变化的总结[1999/07]
99       ASME SEC III D1 ND A99-1999 1999 附录变化的总结[1999/07]
100       ASME SEC III D1 NE A99-1999 1999 附录变化和总结[1999/07]
101       ASME SEC III D1 NF A99-1999 1999 附录变化的总结[1999/07]
102       ASME SEC III D1 NG A99-1999 1999 附录变化的总结[1999/07]
103       ASME SEC III D1 NH A99-1999 1999 附录变化的总结[1999/07]
104       ASME SEC III D1 APP A99-1999 1999 附录变化的总结[1999/07]
105       ASME SEC V B SE-747-1999 SE-747 用于放射线学的电线图象质量指示器(..[1999/07]
106       ASME SEC V B SE-1079-1999 SE-1079 传输显象密度计刻度的标准惯例 AST..[1999/07]
107       ASME SEC V B SE-1114-1999 SE-1114 决定铱-192工业放射性资源的焦点尺..[1999/07]
108       ASME SEC V B SE-1165-1999 SE-1165 采用小孔成像的工业X射线管的焦点的..[1999/07]
109       ASME SEC V B SE-1416-1999 SE-1416 焊件的放射镜检查的标准测试方法 A..[1999/07]
110       ASME SEC XI D1 MA APP I-1999 附录 I 超声检查[1999/07]
111       ASME SEC XI ADD-1999 BPVC XI部分 1999附录，核电厂元件的业务中..[1999/07]
112       ASME MH1A-1999 MH1 - 1997的附录，单位负荷的托盘，滑片，..[1999/06]
113       ASME OMA CODE-1999 OM代码附录-核电厂运行和维护用1998代码[1999/06]
114       ASME A17.1C-1999 电梯和电动扶梯的A17.1-1996安全编码的附录[1999/06]
115       ASME OM CODE CASES-1999 核电厂的运行和维护用OM CODE代码的代码案例[1999/01]
116       ASME Y14.24-1999 工程制图的类型和应用[1999/01]
117       ASME QME-1A-1998 用于核电厂的有效机械设备的资格 QME-1 - 1..[1998/12]
118       ASME PTC 19.1-1998 不确定测试工具和仪器（性能测试码）[1998/12]
119       ASME B56.11.7-1998 电动工业卡车的液体丙烷气体(LPG)燃料汽缸（..[1998/11]
120       ASME B107.38M-1998 电子钳[1998/09]
121       ASME B31.1-1998 电力管道[1998/08]
122       ASME OM CODE-1998 核电厂运行和维护用代码[1998/07]
123       ASME B18.3-1998 插座帽，侧翼，和装置螺孔，六角形和联接键..[1998/07]
124       ASME MFC-6M-1998 用涡流流量计测量管道中的液体流量[1998/07]
125       ASME SEC II B SB-473-1998 SB-473 UNS N08020, UNS N08026, 和 UNS N0..[1998/07]
126       ASME SEC VII-1998 BPVC VII部分非合并电力锅炉（锅炉和压力容..[1998/07]
127       ASME SEC X-1998 BPVC X部分光纤增强塑料压力容器非合并（..[1998/07]
128       ASME SEC XI-1998 BPVC XI 部分核电厂元件的业务中检查规则 ..[1998/07]
129       ASME SEC I-1998 BPVC 部分I 非合并电力锅炉的建筑规则（锅..[1998/07]
130       ASME SEC II-C-1998 BPVC II部分材料C部分-焊接杆，电极，和装..[1998/07]
131       ASME SEC III NCA-1998 BPVC 3部分，核电厂元件的建设原则子部分N..[1998/07]
132       ASME SEC III D1 NB-1998 BPVC 3部分，核设施元件的建设规则第1节-N..[1998/07]
133       ASME SEC III D1 NC-1998 BPVC 3部分，核设施元件的建设规则第1节-N..[1998/07]
134       ASME SEC III D1 ND-1998 BPVC 3部分，核设施元件的建设规则第1节- ..[1998/07]
135       ASME SEC III D1 NE-1998 BPVC 3部分，核设施元件的建设规则第1节- ..[1998/07]
136       ASME SEC III D1 NF-1998 BPVC 3部分，核设施元件的建设规则第1节- ..[1998/07]
137       ASME SEC III D1 NG-1998 BPVC 3部分，核设施元件的建设规则第1节-N..[1998/07]
138       ASME SEC III D1 NH-1998 BPVC 3部分，核电厂元件的建设规则第1节-N..[1998/07]
139       ASME SEC III D1 APPENDICES-1998 BPVC III部分核电厂成分的建筑规则 1分部分..[1998/07]
140       ASME SEC III DIVISION 2-1998 BPVC III部分核电厂元件的建设原则第2节：..[1998/07]
141       ASME SEC III DIVISION 3-1998 BPVC III部分核电厂元件的建设原则第3节：..[1998/07]
142       ASME SEC II A SA-134-1998 管道，钢，电弧焊（尺寸NPS 16以上）的SA-1..[1998/07]
143       ASME SEC II A SA-135-1998 SA-135 电阻焊接钢管规范 ASTM A 135-96[1998/07]
144       ASME SEC II A SA-178/SA-178M-1998 SA-178/SA-178M 电阻焊接碳钢和碳锰钢锅炉和..[1998/07]
145       ASME SEC II A SA-214/SA-214M-1998 SA-214/SA-214M电阻焊接碳钢热交换器和冷凝..[1998/07]
146       ASME SEC II A SA-226/SA-226M-1998 SA-226/SA-226M 用于高压业务的电阻焊接碳钢..[1998/07]
147       ASME SEC II A SA-232/SA-232M-1998 SA-232/SA-232M 铬钒合金钢阀门弹簧质量电线..[1998/07]
148       ASME SEC II A SA-250/SA-250M-1998 SA-250/SA-250M 电阻焊接铁酸盐合金钢锅炉和..[1998/07]
149       ASME SEC VIII D2 ART I-5-1998 第I-5条 X光照相术检查[1998/07]
150       ASME SEC VIII D2 ART T-5-1998 第T-5条压力测试计量器[1998/07]
151       ASME SEC II A SA-358/SA-358M-1998 SA-358/SA-358M 高温业务用电熔合焊接奥氏..[1998/07]
152       ASME SEC II A SA-423/SA-423M-1998 SA-423/SA-423M 无缝和电焊接低合金钢管规范..[1998/07]
153       ASME SEC II A SA-557/SA-557M-1998 SA-557/SA-557M 电阻焊碳钢给水加热管规范 ..[1998/07]
154       ASME SEC II A SA-574-1998 SA-574 合金钢插座头螺丝钉规范 ASTM A 325..[1998/07]
155       ASME SEC II A SA-587-1998 SA-587 化学工业用电阻焊接低碳钢管规范 AS..[1998/07]
156       ASME SEC II A SA-671-1998 SA-671 大气和低温用电气熔合焊接钢管规范 ..[1998/07]
157       ASME SEC II A SA-672-1998 SA-672 用于适度温度的高压业务的电气熔合焊..[1998/07]
158       ASME SEC II A SA-691-1998 SA-691用于高温高压业务的电气熔合焊接碳和..[1998/07]
159       ASME SEC II A SA-905-1998 SA-905 钢制电线规范，压力容器绕组 ASTM A..[1998/07]
160       ASME SEC II B NMA APP B-1998 附录B - 材料的多记号非强制指导方针[1998/07]
161       ASME SEC II B SB-550-1998 SB-550 锆和锆合金棒和电线规范 ASTM B 550-92[1998/07]
162       ASME SEC II B SB-672-1998 SB-672 镍-铁-铬-钼-铌稳定合金(UNS N08700..[1998/07]
163       ASME SEC II B SB-691-1998 SB-691 铁-镍-铬-钼合金(UNS N08366 和 UNS..[1998/07]
164       ASME SEC II C SFA-5.1-1998 SFA-5.1 用于遮蔽金属弧焊的碳钢规范 AWS A..[1998/07]
165       ASME SEC II C SFA-5.4-1998 SFA-5.4 用于遮蔽金属弧焊的不锈钢电极的规..[1998/07]
166       ASME SEC II C SFA-5.5-1998 SFA-5.5 用于遮蔽金属弧焊的低合金钢电极的..[1998/07]
167       ASME SEC II C SFA-5.6-1998 SFA-5.6 隐蔽铜和铜合金弧焊电极的规范 AWS..[1998/07]
168       ASME SEC II C SFA-5.7-1998 SFA-5.7 铜和铜合金裸焊接杆和电极的规范 A..[1998/07]
169       ASME SEC II C SFA-5.9-1998 SFA-5.9 裸露不锈钢焊接电极和杆的规范 AWS..[1998/07]
170       ASME SEC II C SFA-5.10-1998 SFA-5.10 裸铝和铝合金焊接电极和棒规范 A..[1998/07]
171       ASME SEC II C SFA-5.13-1998 SFA-5.13 固态表面焊接杆和电极规范 AWS A5..[1998/07]
172       ASME SEC II C SFA-5.15-1998 SFA-5.15 铸铁用焊接电极和杆的规范 AWS A5..[1998/07]
173       ASME SEC II C SFA-5.16-1998 SFA-5.16 钛和钛合金焊接电极和杆的规范 AW..[1998/07]
174       ASME SEC II C SFA-5.18-1998 SFA-5.18 用于气体遮蔽弧焊的碳钢电极和杆的..[1998/07]
175       ASME SEC II C SFA-5.21-1998 SFA-5.21 合成表面焊接杆和电极的规范 AWS ..[1998/07]
176       ASME SEC II C SFA-5.22-1998 SFA-5.22 用于助焊剂核心电弧焊的不锈钢电极..[1998/07]
177       ASME SEC II C SFA-5.24-1998 SFA-5.24 锆和锆合金焊接电极和杆的规范 AW..[1998/07]
178       ASME SEC II D APPENDIX 7-1998 附录 7 材料的多标记指导[1998/07]
179       ASME SEC III NCA ACI-1998 美国混凝土学会[1998/07]
180       ASME SEC III NCA-2000-1998 第NCA-2000条元件和支持的分类[1998/07]
181       ASME SEC III D1 NB A98-1998 1998 附录变化的总结[1998/07]
182       ASME SEC III D1 NC A98-1998 1998 附录变化的总结[1998/07]
183       ASME SEC III D1 ND A98-1998 1998 附录变化的总结[1998/07]
184       ASME SEC III D1 NE A98-1998 1998 附录变化和总结[1998/07]
185       ASME SEC III D1 NF A98-1998 1998 附录变化的总结[1998/07]
186       ASME SEC III D1 NG A98-1998 1998 附录变化的总结[1998/07]
187       ASME SEC III D1 NH A98-1998 1998 附录变化的总结[1998/07]
188       ASME SEC III D1 APP A98-1998 1998 附录变化的总结[1998/07]
189       ASME SEC III D1 MA APP XXIII-1998 附录 XXIII 专业工程师的资格和责任[1998/07]
190       ASME SEC III D2 CC-6000-1998 第CC-6000条混凝土包装物的结构完整测试[1998/07]
191       ASME SEC III D2 CC-7000-1998 第CC-7000条过压保护[1998/07]
192       ASME SEC III D2 MA APP III-1998 附录III 术语表[1998/07]
193       ASME SEC III D2 MA APP XI-1998 附录XI 电弧焊增强棒的资格[1998/07]
194       ASME SEC III D3 WA-2000-1998 第WA-2000条运输包装物的包装系统的设计基础[1998/07]
195       ASME SEC III D3 WA-3000-1998 第WA-3000条责任[1998/07]
196       ASME SEC III D3 WA-4000-1998 第WA-4000条质量保证[1998/07]
197       ASME SEC III D3 WA-9000-1998 第WA-9000条术语表[1998/07]
198       ASME SEC V B SE-142-1998 SE-142 控制放射线测试的质量的标准方法 AS..[1998/07]
199       ASME SEC V B SE-186-1998 SE-186[1998/07]
200       ASME SEC V B SE-242-1998 SE-242 用于在某种参数变化时X光图象的外观..[1998/07]
201       ASME SEC V B SE-999-1998 SE-999 工业X光照相胶卷处理的质量控制的标..[1998/07]
202       ASME SEC V B SE-1030-1998 SE-1030 金属铸件的放射检查的标准测试方法..[1998/07]
203       ASME SEC V B SE-1647-1998 SE-1647 决定放射线透视中对比敏感度的标准..[1998/07]
204       ASME SEC V B SE-1815-1998 SE-1815 用于工业X光照相术的胶卷系统分类的..[1998/07]
205       ASME SEC V B SE-797-1998 SE-797 用手动超声脉冲-回声接触方法测量厚..[1998/07]
206       ASME SEC V B SD-129-1998 SD-129 石油产品中的硫磺的标准测试方法（一..[1998/07]
207       ASME SEC V B SD-516-1998 SD-516 水中硫酸盐离子的标准测试方法 ASTM..[1998/07]
208       ASME SEC V B SD-808-1998 SD-808 在新的和用过的石油产品中的氯的标准..[1998/07]
209       ASME SEC V B SD-1552-1998 SD-1552 石油产品中的硫磺的标准测试方法（..[1998/07]
210       ASME SEC V B SE-709-1998 SE-709 磁粒子检查的标准指导 ASTM E709-95[1998/07]
211       ASME SEC V B SE-309-1998 SE-309 采用磁浸透的钢管产品的检查的标准惯..[1998/07]
212       ASME SEC V B SE-426-1998 SE-426 无缝和焊接管状产品，奥氏不锈钢，和..[1998/07]
213       ASME SEC V B SE-571-1998 SE-571 镍和镍合金管状产品的电磁（涡流）检..[1998/07]
214       ASME SEC VII GLOSSARY-1998 术语表[1998/07]
215       ASME SEC VIII D1 MA APP 6-1998 附录6 磁粒子检查方法(MT)[1998/07]
216       ASME SEC VIII D1 MA APP 7-1998 附录 7 钢铸件的检查[1998/07]
217       ASME SEC VIII D1 MA APP 12-1998 附录 12 焊接的超声检查(UT)[1998/07]
218       ASME SEC VIII D1 MA APP 19-1998 附录19 电热或气体燃烧带外罩的蒸汽壶[1998/07]
219       ASME SEC VIII D3 ART KT-3-1998 第KT-3条流体静力学测试[1998/07]
220       ASME SEC VIII D3 ART KT-4-1998 第KT-4条压力测试计量器和传感器[1998/07]
221       ASME SEC X ART RD-12-1998 第RD-12条碾压硬度系数[1998/07]
222       ASME SEC X MA APP 4-1998 附录4-有关光纤增强塑料的强制术语[1998/07]
223       ASME SEC X MA APP 5-1998 附录5-液体树脂的强制特殊重力[1998/07]
224       ASME QRO-1B-1998 资源修复装置操作者的资格和认证标准 QRO-1..[1998/05]
225       ASME B107.45M-1998 劈凿和地板/电工凿子：安全要求[1998/04]
226       ASME B5.49-1998 电力压力术语[1998/03]
227       ASME B107.29M-1998 电子测试装置，手动扭距工具[1998/02]
228       ASME Y14.100M-1998 工程制图惯例[1998/02]
229       ASME QRO-1b Addenda-1998 资源修复装置操作者的资格和认证[1998/01]
230       ASME OMA-S/G-1998 OM-S/G的附录-1998 核电厂运行和维护的标准..[1998/01]
231       ASME TDP-1-1998 用于产生电力的蒸汽涡轮的防水损害的推荐惯例[1998/01]
232       ASME PTC 4-1998 火力蒸汽发电机[1998/01]
233       ASME A17.1B-1998 电梯和电动扶梯的A17.1-1996安全编码的附录[1998/01]
234       ASME A17.2.1B-1998 电动电梯的A17.2.1-1996检查员手册的附录[1998/01]
235       ASME A17.2.2A-1998 水压电梯的A17.2.2-1997检查员手册的附录[1998/01]
236       ASME A17.2.3-1998 电梯和移动人行道包括其检查程序的检查员手册[1998/01]
237       ASME A17.2.3 INT NO 1-1998 电动扶梯和移动人行道的A17.2.3-1998检查员..[1998/01]
238       ASME B40.100-1998 压力量表和量表附件集成ASME B40.1-1998 和..[1998/01]
239       ASME QME-1-1997 用于核电厂的有效机械设备的资格[1997/12]
240       ASME A17.2.2-1997 水压电梯的检查员手册[1997/12]
241       ASME B107.28M-1997 电子扭距工具[1997/12]
242       ASME MH1-1997 单位负荷的托盘，滑片，和其它基础，取代MH..[1997/12]
243       ASME B29.10M-1997 繁重责任抵消工具条电力传输滚筒链和链轮齿[1997/10]
244       ASME PALD-1997 便携式汽车提升装置的安全标准[1997/10]
245       ASME PTC 19.11-1997 电力循环中蒸汽和水取样，调节，和分析（性..[1997/10]
246       ASME B107.34M-1997 火花塞的插座扳手[1997/09]
247       ASME PTC 22-1997 燃气涡轮机的性能试验规则[1997/09]
248       ASME B1.10M-1997 统一微型螺纹勘误表[1997/09]
249       ASME QEI-1-1997 电梯检查员的资格标准[1997/07]
250       ASME A17.1A-1997 电梯和电动扶梯的A17.1-1996安全编码的附录[1997/01]
251       ASME A17.2.1A-1997 电动电梯的A17.2.1-1996检查员手册的附录[1997/01]
252       ASME B1.5-1997 Acme 螺纹[1997/01]
253       ASME B1.21M-1997 公制螺纹：MJ 剖面[1997/01]
254       ASME PTC 22-1997 燃气涡轮机的性能试验规则[1997/01]
255       ASME A17.1-1996 电梯和电动扶梯的安全编码[1996/10]
256       ASME A17.3-1996 现有电梯和电动扶梯的安全编码[1996/10]
257       ASME MH1.8M-1996 木头托盘[1996/09]
258       ASME A17.2.1-1996 电动电梯的检查员手册[1996/09]
259       ASME A17.5-1996 电梯和电动扶梯的电气设备[1996/07]
260       ASME B 107.27-1996 多位钳(电连接头)[1996/01]
261       ASME QRO-1a Addenda-1996 资源回收设备操作人员的资格证书和认证的标..[1996/01]
262       ASME MH 1.8M-1996 木托盘[1996/01]
263       ASME PTC 6-1996 汽轮机[1996/01]
264       ASME Y 14.34M-1996 相关表格[1996/01]
265       ASME A17.1 HDBK-1996 电梯和自动扶梯的安全编码手册[1996/01]
266       ASME B107.10M-1996 手动插座扳手的把手和附件-英制和公制系列[1996/01]
267       ASME QRO-1A-1996 资源回收设备操作人员的资格证书和认证的标..[1996/01]
268       ASME SPPE-1D-1996 SPPE-1-1994的附录用于海上石油和气运营防..[1996/01]
269       ASME SPPE-2D-1996 SPPE-2-1994的附录用于海上石油和气运营的..[1996/01]
270       ASME B16.11-1996 锻造装置，插座焊接和螺纹[1996/01]
271       ASME B29.26M-1996 疲劳测试电力传输滚筒链[1996/01]
272       ASME B1.15-1995 统一英寸螺纹勘误表[1995/08]
273       ASME MFC-14M-1995 用小孔径精确孔板流量计测量液体流量[1995/01]
274       ASME MFC-16M-1995 用电磁流量计在密封管中对液体流量的测量[1995/01]
275       ASME B 107.4M-1995 便携式手工、冲击、气动和电动工具用驱动和..[1995/01]
276       ASME B94.56-1995 计量器-功能的，球锁冲床（英制）[1995/01]
277       ASME B94.56.1M-1995 计量器-功能的，球锁冲床（公制）[1995/01]
278       ASME SPPE-1B-1995 SPPE-1-1994的附录用于海上石油和气运营防..[1995/01]
279       ASME SPPE-1C-1995 SPPE-1-1994的附录用于海上石油和气运营防..[1995/01]
280       ASME SPPE-2B-1995 SPPE-2-1994的附录用于海上石油和气运营的..[1995/01]
281       ASME SPPE-2C-1995 SPPE-2-1994的附录用于海上石油和气运营的..[1995/01]
282       ASME Y14.1-1995 十进制英寸制图单的尺寸和格式[1995/01]
283       ASME Y14.1M-1995 公制制图单的尺寸和格式[1995/01]
284       ASME B1.13M-1995 公制螺纹-M剖面[1995/01]
285       ASME B19.1-1995 空气压缩系统的安全标准[1995/01]
286       ASME B19.3B-1995 加工工业压缩机安全标准的B19.3-1991的附录[1995/01]
287       ASME QRO-1-1994 资源回收设备操作人员的资格证书和认证的标准[1994/01]
288       ASME B 133.9-1994 固定式燃气涡轮内机的废气排放测量[1994/01]
289       ASME MFC-10M-1994 确定安装对流量计上的影响的方法[1994/01]
290       ASME B56.11.4A-1994 电动工业铲车的钩型叉和叉搬运器 B56.11.4-..[1994/01]
291       ASME B56.11.5A-1994 低升力，高升力，和粗糙地形电动工业卡车的..[1994/01]
292       ASME B107.5M-1994 插座扳手，手动（公制系列）[1994/01]
293       ASME SPPE-1-1994 用于海上石油和气运营防污染设备，安全证明..[1994/01]
294       ASME SPPE-1A-1994 SPPE-1-1994的附录用于海上石油和气运营防..[1994/01]
295       ASME SPPE-2-1994 用于海上石油和气运营的防污染设备和实验室..[1994/01]
296       ASME SPPE-2A-1994 SPPE-2-1994的附录用于海上石油和气运营的..[1994/01]
297       ASME B5.55M-1994 电力压力刹车，规范和性能标准[1994/01]
298       ASME B5.56M-1994 电动剪床，规范和性能标准[1994/01]
299       ASME B19.3A-1994 加工工业压缩机安全标准的B19.3-1991的附录[1994/01]
300       ASME B29.3M-1994 双倍斜度电力传输滚筒链和链轮齿[1994/01]
301       ASME MH 1.9-1993 出口托盘[1993/01]
302       ASME N 626.3-1993 特殊专业工程师的资格鉴定和责任[1993/01]
303       ASME B 96.1-1993 焊接铝合金储存罐[1993/01]
304       ASME B107.1-1993 插座扳手，手动（英制系列）[1993/01]
305       ASME MH1.5M-1993 滑动片[1993/01]
306       ASME MH1.9-1993 出口托盘[1993/01]
307       ASME PTC PM-1993 蒸汽电力厂的性能监测指导[1993/01]
308       ASME B1 TECH REPT-1993 60度螺纹计量要素测量（英制和公制）的测量..[1993/01]
309       ASME B29.1M-1993 精确电力传输滚筒链，附件，和链轮齿[1993/01]
310       ASME B56.11.5-1992 低升力，高升力，和粗糙地形电动工业卡车的..[1992/11]
311       ASME B56.11.6-1992 电力工业卡车的可见度评价[1992/11]
312       ASME B56.11.4-1992 电动工业铲车的钩型叉和叉搬运器特殊通知-..[1992/01]
313       ASME Y14.2M-1992 线条惯例和字体[1992/01]
314       ASME B1.3M-1992 用于空间可接受性的螺纹计量系统-英制和公制..[1992/01]
315       ASME B1.30M-1992 螺纹-计算和环绕尺寸的标准惯例[1992/01]
316       ASME MFC-1M-1991 密封管道中液体流量测量用术语汇编[1991/08]
317       ASME B1.20.5-1991 干封管道螺纹的计量[1991/01]
318       ASME B1.20.7-1991 软管接合螺纹[1991/01]
319       ASME B19.3-1991 加工工业压缩机的安全标准[1991/01]
320       ASME MFC-3M Errata-1990 用孔板,管接头和文丘里管测量管道中的流量...[1990/01]
321       ASME N509-1989 核电厂空气清洁装置和元件勘误[1989/06]
322       ASME Y 14.26M-1989 产品测定数据通讯用数字表示法[1989/01]
323       ASME Y 14/TR 4-1989 基本形状描述用结构化语言格式[1989/01]
324       ASME MFC-3M-1989 用孔板,管接头和文丘里管测量管道中的液体流..[1989/01]
325       ASME MFC-11M-1989 用科氏质量流量计测量液体流量[1989/01]
326       ASME MFC-9M Errata-1989 在封闭导管中用称重法测量液体流量.正误表[1989/01]
327       ASME MH 1.4.1M-1989 托盘试验程序[1989/01]
328       ASME MH 1.2.2M-1989 托盘尺寸[1989/01]
329       ASME MH 1.1.2-1989 涉及托盘及相关结构的定义和术语[1989/01]
330       ASME MH1.2.2M-1989 托盘尺寸[1989/01]
331       ASME N510-1989 核空气处理系统的测试[1989/01]
332       ASME Y14.26M-1989 产品定义数据通讯的数字表示法[1989/01]
333       ASME Y14 TECH REPT 4-1989 用于基本形状描述的结构语言格式[1989/01]
334       ASME B1.1-1989 统一英寸螺纹[1989/01]
335       ASME MFC-9M-1988 在封闭导管中用称重法测量液体流量[1988/01]
336       ASME MFC-8M-1988 封闭导管中液体流量.初级和次级装置间压力信..[1988/01]
337       ASME PTC 6S Report-1988 汽轮机常规运行试验程序[1988/01]
338       ASME MH 1.7M-1988 托盘及相关结构的组合用传动紧固件[1988/01]
339       ASME B1.8-1988 短粗Acme螺纹[1988/01]
340       ASME MFC-7M-1987 用极限流量文氏喷嘴测量气体流量[1987/01]
341       ASME MFC-6M Errata-1987 用涡流流量计测量管道中的液体流量.正误表[1987/01]
342       ASME MFC-6M-1987 用涡流流量计测量管道中的液体流量[1987/01]
343       ASME MH 1.6-1987 木制托盘和相关结构耐久性测定用标准程序[1987/01]
344       ASME PTC 19.2-1987 第2部分：压力测量工具和仪器（性能测试码）[1987/01]
345       ASME B1.12-1987 5级冲突安装螺纹[1987/01]
346       ASME MFC-4M-1986 用汽轮计测量气体流量[1986/07]
347       ASME Y14.18M-1986 光学部分[1986/01]
348       ASME PTC 19.22-1986 第22部分：数字系统技术工具和仪器（性能测..[1986/01]
349       ASME B18.3.1M-1986 插座头帽螺旋（公制系列）[1986/01]
350       ASME B18.3.3M-1986 六角形插座头侧翼螺孔（公制系列）[1986/01]
351       ASME B18.3.4M-1986 六角形插座按钮头螺帽（公制系列）[1986/01]
352       ASME B18.3.5M-1986 六角形插座扁平防下陷头螺帽（公制系列）[1986/01]
353       ASME B18.3.6M-1986 公制系列插座装置螺孔[1986/01]
354       ASME MFC-5M-1985 在封闭导管中用渡越时间超声波流量计测量液..[1985/01]
355       ASME PTC 6 Report-1985 汽轮机运行试验中测量不确定度的评定导则[1985/01]
356       ASME B 133.7M-1985 燃气轮机的燃料[1985/01]
357       ASME B1.22M-1985 MJ系列公制螺纹的计量和计量器[1985/01]
358       ASME Y 10.3M-1984 机械和与时间相关的现象用字母符号[1984/01]
359       ASME Y10.11-1984 在声学中使用的数量的文字符号和缩写 ASA Y..[1984/01]
360       ASME B1.7M-1984 螺纹的术语，定义，和文字符号[1984/01]
361       ASME B1.16M-1984 公制M螺纹的计量和计量器[1984/01]
362       ASME MFC-2M-1983 密封管道中液体流量测量的不确定度[1983/01]
363       ASME B 133.1M-1983 燃气轮机的术语[1983/01]
364       ASME B1.2-1983 统一英寸螺纹的计量和计量器勘误表[1983/01]
365       ASME B1.20.1-1983 管道螺纹，一般目的[1983/01]
366       ASME B16.41-1983 核电厂的电动活跃阀门组件的功能资格要求[1983/01]
367       ASME B56.11.3-1982 电动工业卡车的负荷处理符号特殊通知-1993..[1982/04]
368       ASME SI-9 Errata-1982 SI(米)单位代码和标准的公制化指南.正误表[1982/01]
369       ASME Y 10.4-1982 热学和热力学用字母符号[1982/01]
370       ASME Guide SI-1-1982 国际单位的使用指南和取向[1982/01]
371       ASME N626.0-1982 授权的视察机构，核检查者，和核检查监督者..[1982/01]
372       ASME N626.1-1982 授权的视察机构，核服务中检查者，和核服务..[1982/01]
373       ASME N626.2-1982 授权的视察机构，核检查者（具体的），和核..[1982/01]
374       ASME PTC 4.4-1981 燃气轮机热回收蒸汽发生器[1981/01]
375       ASME B 133.12-1981 燃气轮机的维护和安全[1981/01]
376       ASME B 133.10-1981 由使用者和制造者提供的燃气轮机信息[1981/01]
377       ASME B 133.3-1981 燃气轮机辅助设备[1981/01]
378       ASME Y14.13M-1981 机械弹簧表示法[1981/01]
379       ASME PTC 19.7-1980 第7部分：轴状电力工具和仪器的测量（性能..[1980/01]
380       ASME PTC 19.23-1980 第23部分：模型测试工具和仪器的指导手册（..[1980/01]
381       ASME B5.52M-1980 机械电压通用目的单点，GAP 类型（公制）[1980/01]
382       ASME B 133.6-1978 燃气轮机的额定值和性能[1978/01]
383       ASME B 133.5-1978 燃气轮机的电气设备[1978/01]
384       ASME B 133.4-1978 燃气轮机的控制和保护系统[1978/01]
385       ASME B133.5-1978 气体涡轮电气设备的获得标准[1978/01]
386       ASME B133.6-1978 气体涡轮额定电压和性能的获得标准[1978/01]
387       ASME PTC 20.1-1977 汽轮发电机组的速度和负载调节系统[1977/01]
388       ASME B 133.8-1977 燃气轮机装置噪音释放[1977/01]
389       ASME B 133.2-1977 主燃气轮机[1977/01]
390       ASME Y14 REPORT 3-1977 用于产品定义数据设计要求的计算机辅助准备..[1977/01]
391       ASME SI-3-1976 动力学SI单位[1976/01]
392       ASME Y14 REPORT-1976 物体外形的数字表示法[1976/01]
393       ASME B1.20.3-1976 干封管道螺纹（英寸）[1976/01]
394       ASME Y 32.2-1975 电气图和电子图用图形符号(包括基准标识类别..[1975/01]
395       ASME N278.1-1975 自动运行和电力驱动安全相关阀门的功能规范..[1975/01]
396       ASME PTC 19.3-1974 第3部分：温度测量工具和仪器（性能测试码）[1974/01]
397       ASME PTC 17-1973 往复式内燃机[1973/01]
398       ASME N 45.2.10-1973 质量保证的术语和定义[1973/01]
399       ASME B 89.6.2-1973 尺寸测量的温度和湿度环境[1973/01]
400       ASME B1.9-1973 支持英制螺纹7度/45度格式，螺纹结合的基本..[1973/01]
401       ASME MC 88.1-1972 压力传感器的动态校准导则[1972/01]
402       ASME B 89.3.1-1972 不圆度的测量[1972/01]
403       ASME B94.40-1972 冲床-电线类型[1972/01]
404       ASME Y10.1-1972 有关文字符号的术语[1972/01]
405       ASME Y32.18-1972 用于示意性图表的机械和声学元素符号[1972/01]
406       ASME PTC 19.5-1972 流度仪表的应用部分II（性能测试代码）[1972/01]
407       ASME PTC 20.3-1970 汽轮发电机组用压力控制系统[1970/01]
408       ASME PTC 6S-70 REPORT-1970 汽轮机常规运行试验的简化程序[1970/01]
409       ASME PTC 19.8-1970 第8部分：指示电力工具和仪表的测量（性能..[1970/01]
410       ASME Y 10.5-1968 电气科学和电气工程中量的字母符号[1968/01]
411       ASME PTC 4.3-1968 空气加热器.PTC4.1蒸汽发生组件运行测试规程..[1968/01]
412       ASME Y10.18-1967 照明工程的文字符号[1967/01]
413       ASME PTC 20.2-1965 汽轮发电机组用超速自动分离系统[1965/01]
414       ASME PTC 29-1965 水力涡轮发电机装置的速度支配系统（性能测..[1965/01]
415       ASME PTC 19.5.1-1964 装置和仪器.第5部分:材料数量测量.第1节:称..[1964/01]
416       ASME PTC 26-1962 内燃机发电机装置的速度支配系统（性能测试..[1962/01]
417       ASME PTC 19.14-1958 第14部分：线性测量工具和仪器（性能测试码）[1958/01]
418       ASME B1.11-1958 显微镜客观螺纹勘误表[1958/01]
419       ASME Y32.2.6-1950 热动力设备的绘图符号[1950/01]

用户名		自动登录	找回密码
密码			注册

【转帖】asme美国机械工程师标准目录2

回复: 【转帖】asme美国机械工程师标准目录2

回复: 【转帖】asme美国机械工程师标准目录2

回复: 【转帖】asme美国机械工程师标准目录2

回复: 【转帖】asme美国机械工程师标准目录2

回复: 【转帖】asme美国机械工程师标准目录2