几何尺寸与公差论坛

 找回密码
 注册
查看: 95|回复: 7

PR 260789 can't get angle more than 180 degree even F5 set to 0-360 degree

[复制链接]
发表于 2009-7-22 21:10:52 | 显示全部楼层 |阅读模式
<< Alex Ang  --  03/26/09  18:36:03>>
can't get angle more than 180 degree even F5 set to 0-360 degree

Steps to reproduce:
measurement angle more than 180 degree

Results:
if result more than 180 degree, example 185 degree. PC-DMIS only gives 5 degree

Expected Results:
expected 185 degree
<<END>>
<< Changes made by Alex Ang (Field Changes) -- 04/23/09  14:04:08>>
Status:  RESOLVED to CLOSED
<<END>>
<< Alex Ang (Customer Notes)  --  04/23/09  14:03:55>>
thanks
<<END>>
<< Don Turcotte (Development Notes)  --  04/22/09  13:21:50>>
The latest version of V42 MR3  which is available on the Wilcox web site for download works correctly.  By default the angle LIN1 to LIN2 is 254 and the angle LIN2 to LIN1 is 106.  However, you can edit the nominal for LIN2 to LIN1 to set it 254 if this is the quadrant you want.
<<END>>
<< Alex Ang (Customer Notes)  --  04/21/09  13:35:10>>
new version? then isn't means V4.2 can't do this.
<<END>>
<< Yanhua Huang (Development Notes)  --  04/14/09  19:06:52>>
Upload to a new version?
<<END>>
<< Alex Ang (Customer Notes)  --  04/13/09  08:31:09>>
how to i find a solution which you mean already fixed by someone.
<<END>>
<< Changes made by Yanhua Huang (Field Changes) -- 04/09/09  21:32:56>>
Status:  MOREINFO to RESOLVED
<<END>>
<< Changes made by Yanhua Huang (Resolution Data) -- 04/09/09  21:32:52>>
** Unable to Duplicate -  -  -  **
<<END>>
<< Yanhua Huang (Development Notes)  --  04/09/09  21:31:14>>
Alex,
I could not duplicate this in the latest V42R, V432. Someone had fixed this.
yanhua.huang@hexagonmetrology.com
From: ANG Alex [mailto:Alex.Ang@hexagonmetrology.com]
Hi,
Are you using V4.3 because I still can't get the result like yours.
DIM ANGL2= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A    -106.000      0.010      0.010   -106.000      0.000      0.000 ---#----
DIM ANGL3= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A     254.000      0.010      0.010    -74.000   -328.000    327.990 <-------
Alex

Alex,
Please change the selection order. You should get 254 degree.
Firstly select LIN1, then select LIN2.

DIM ANGL3= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A    254.00000    0.01000   -0.01000  254.00000    0.00000    0.00000 ---#----
yanhua.huang@hexagonmetrology.com

Hi Huang,
My concern's how to get the MAJOR ANGLE which is 254 degree(360-106), thanks.
Regards,
alex
<<END>>
<< Yanhua Huang (Test Notes)  --  04/08/09  21:44:26>>
2D angle is calculated -> the counterclockwise rotate angle from vector of considered feature to vector of datum feature.
<<END>>
<< Yanhua Huang (Test Notes)  --  04/08/09  21:35:58>>
Alex,
what is your email address?
<<END>>
<< Alex Ang (Customer Notes)  --  04/08/09  21:22:04>>
any progress for this issue, thanks
<<END>>
<< Yanhua Huang (Test Notes)  --  04/08/09  21:10:38>>
Alex,
What result are you expecting in your attached PP?
I did test in V42R, V432 and V44B, got the same result as below.
DIM ANGL2= 2D ANGLE FROM LINE LIN2 TO LINE LIN1 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A   106.00000    0.01000   -0.01000  106.00000    0.00000    0.00000 ---#----
<<END>>
<< Alex Ang (Customer Notes)  --  04/03/09  08:50:55>>
hi, attached is the sample pp. thanks.
<<END>>
<< Changes made by Yanhua Huang (Field Changes) -- 04/01/09  20:21:58>>
Action:  Yanhua Huang to Alex Ang, Status:  OPEN to MOREINFO
<<END>>
<< Yanhua Huang (Development Notes)  --  04/01/09  20:21:33>>
Please attach your test PP.
<<END>>
<< Changes made by Tim Wernicke -- 03/26/09  08:31:46>>
Action:  Tim Wernicke to Yanhua Huang, Assigned:   to Yanhua Huang, Priority:  to High
<<END>>
 楼主| 发表于 2009-7-22 21:11:19 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Alex,
What result are you expecting in your attached PP?  
I could not duplicate your reported issue (185 degree ->5 degree). In your attached PP, the angle between two lines is near 90 degree.
2D angle is calculated via the counterclockwise from vector of considered feature to vector of datum feature.

I did test in V42R, V432 and V44B, got the same result as below.
DIM ANGL2= 2D ANGLE FROM LINE LIN2 TO LINE LIN1 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A   106.00000    0.01000   -0.01000  106.00000    0.00000    0.00000 ---#----
<<END>>
yanhua.huang@hexagonmetrology.com
 楼主| 发表于 2009-7-22 21:11:40 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Hi Huang,

My concern’s how to get the MAJOR ANGLE which is 254 degree(360-106), thanks.

Regards,
alex
 楼主| 发表于 2009-7-22 21:12:08 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Alex,
Please change the selection order. You should get 254 degree.
Firstly select LIN1, then select LIN2.


DIM ANGL3= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A    254.00000    0.01000   -0.01000  254.00000
 楼主| 发表于 2009-7-22 21:12:37 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Hi,

Are you using V4.3 because I still can’t get the result like yours.

DIM ANGL2= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A    -106.000      0.010      0.010   -106.000      0.000      0.000 ---#----
DIM ANGL3= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A     254.000      0.010      0.010    -74.000   -328.000    327.990 <-------
 楼主| 发表于 2009-7-22 21:13:02 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Alex,
I am using V44B, I will test this in V432. You can try…
1.        F5 set to 0-360 degree
2.        Delete any angle dimension from edit window.
3.        Save PP.
4.        Reopen the program
5.        Create a new 2D angle dimension (LIN1 – LIN2)
Please tell me what result you get.

yanhua.huang@hexagonmetrology.com
 楼主| 发表于 2009-7-22 21:13:19 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Huang,

Still the same as below, I’m using V4.2R. please advice.

DIM ANGL1= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A     254.000      0.010      0.010    -74.000   -328.000    327.990 <-------
DIM ANGL2= 2D ANGLE FROM LINE LIN1 TO LINE LIN2 ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX    NOMINAL       +TOL       -TOL       MEAS        DEV     OUTTOL
A    -106.000      0.010      0.010   -106.000      0.000      0.000 ---#----

Regards,
Alex
 楼主| 发表于 2009-7-22 21:13:38 | 显示全部楼层

回复: PR 260789 can't get angle more than 180 degree even F5 set to 0-360 de

Alex,
I could not duplicate this in the latest V42R, V432. Someone had fixed this.

yanhua.huang@hexagonmetrology.com
您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|Archiver|小黑屋|几何尺寸与公差论坛

GMT+8, 2024-12-22 12:40 , Processed in 0.042530 second(s), 20 queries .

Powered by Discuz! X3.4 Licensed

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表