几何尺寸与公差论坛

 找回密码
 注册
查看: 5030|回复: 3

Ug术语中英对照表cam部分

[复制链接]
发表于 2007-2-13 23:32:54 | 显示全部楼层 |阅读模式
UG术语中英对照表CAM部分

Safe Clearance 安全距离  
Same As CLS     
CLS相同
  
Same As Drive Path  
与驱动导轨(刀具轴)相同
  
Same  Start  And End Axis  
与开始和结束刀轴矢量相同
  
Same Start and End Point   
与开始和结束点相同
  
Sample   
样例 
   
Save 3D   
保存三维模型
  
Save As Global   
保存为全局
  
Save Current Csys   
保存当前的坐标系
  
Save Failed     
保存失败
  
Save/Restore Csys     
保存/恢复坐标系
  
Scallop Height   
残留高度
  
Seed Face
种子面
  
Segment Consistency   
段连续
  
SEL END POINT   
选择终点
  
SEL START POINT   
选择起点
  
Select a Group   
选择一个组
  
Select Adjacent Faces  
选择相邻面
  
Select chain end     
选择链末端
  
Select chain start   
选择链始端
  
Select Head  
选择主轴头
  
Select Holes   
选择孔
  
Select Next Row   
选择下一行
  
Selection Method   
选择方法
  
Self Intersection   
自相交
  
Separator Item     
分隔符
  
Sequence Number  
顺序号
  
Sequencing         
顺序
  
Sequential Milling  
顺序铣
  
Set Modes  
设置模式
  
SET/ADJUST      
设置/调整
  
Setup Events  
设置事件
  
Setup Template   
设置模板
  
Setup
设置
  
SFM      
每分钟英尺(表面线速度)
  
Shape   
外形
  
Shop Documentation
车间工艺文档
  
Shortest Path
Horizontal   最短刀轨,水平的
  
Show 3D   
显示三维模型
  
Show Excess   
显示剩余量
  
Show Gouging     
显示过切
  
Side Cut     
侧削
  
Side Trimmed   
侧修剪
  
Silhouette      
轮廓
  
Silhouette Display   
轮廓显示
  
Simulated     
模拟
  
Single     
单一
  
Single Pass   
单条刀轨
  
Skip   
跳过
  
Slowdowns  
降速
  
Smart Object Action   
相关联对象激活
  
Smart Objects   
相关联对象
  
SMM   
每分钟毫米(表面速度)
  
Solid Center   
刀轨实线(显示
)  
Specify     
指定
  
Specify Boundary   
指定边界
  
Specify Boundary Plane   
指定边界平面
  
Specify Colors     
指定颜色
  
Specify Cut Angle     
指定切削角度
  
Specify Pattern     
指定切削模式
  
Specify Point   
指定点
  
Specify Setup   
指定设置
  
Specify Tool Axis   
指定刀具轴
  
Speed      
转速
  
Spherical Coords     
球坐标
  
Spindle Axis     
主轴
  
Spindle Off  
主轴停止
  
Spindle On
主轴启动
  
Spindle Range Active   
主轴转速范围激活
  
Spindle Speed  
主轴转速
  
Spindle Speed Active   
主轴转速激活
  
Spiral   
螺旋线驱动
  
Spiral Center Point   
螺旋线中心点
  
Spiral Drive Method   
螺旋线驱动方法
  
Split Closed Boundary   
断开封闭的边界
  
Standard Bore      
标准镗
  
Standard Bore, Back      标准镗 插孔

Standard Bore, Drag      
标准镗,快退
Standard Bore, Manual     
标准镗,手动退刀  
Standard Bore, No Drag      
标准镗,横向偏置后快退
  
Standard Drill     
标准钻削
  
Standard Drill, Break Chip     
标准钻削,断屑
  
Standard Drill, Sink     
标准钻削,沉孔
  
Standard Drill, Deep  
标准钻削,深孔
  
Standard Drive   
标准驱动铣
  
Standard Tap     
标准攻螺纹
  
Standard Text     
标准文本(输出)
  
Start & End Points   
开始和结束点
  
Start first %     
最初开始百分比
  
Start last %     
最后开始百分比
  
Start Marker  
起始点标记
  
Start of range   
起始范围
  
Start Point      
起始点
  
Start step   
起始步长
  
Startup   
启动
  
Startup Commands     
启动命令
  
Startup Position     
启动位置
  
Static Material Removal   
静态材料去除
  
Status      
状态
  
Steep     
陡峭壁
  
Steep Angle  
陡峭壁角度
  
Steep Area     
陡峭壁区域
  
Steep Faces   
陡峭壁面
  
Steep Merge   
陡峭壁合并
  
Steep Option   
陡峭壁选项
  
Steep Overlap   
陡峭壁重叠
  
Steep Part      
陡峭壁零件
  
Step Over   
步距(进给速度
)  
Step Size   
步长大小
  
Step Type/Dir  
步距类型/方向
  
Stepover Method   
步距方法
  
Stepover Parameters   
步距参数
  
Stepover
步距
  
Stock  
余量
  
Stock type   
余量类型
  
Stock value   
余量值
  
Stop Animation     
停止动态模拟
  
Stopping Position   (
刀具)停止位置
  
StptChange   
起始点改变
  
Subop to Execute   
执行子操作
  
Sub-Operations   
子操作
  
Sub-Type   
子类型
  
Suppress Tool Path     
压缩刀轨
  
Surf Cont   
曲面连续
  
Surf. Contour   
曲面轮廓
  
Surface Area Drive   
曲面驱动
  
Surface Drive Method   
曲面驱动方法
  
Surface  Inside Tolerance   
曲面内公差
  
Surface Outside Tolerance   
曲面外公差
  
Surface Percentage Method     
曲面百分比方法
  
Surface Region Editing   
曲面区域编辑
  
Surface Region
曲面区域(特征
)  
Surface Speed     
表面切削速度
  
Surface Stock   
曲面余量
  
Swarf Drive  
直纹面驱动
  
T  
Table     
工作台
  
Tangent to Curve   
相切于曲线
  
Tangent to DS     
相切于驱动面
  
Tangent to PS     
相切于零件面
  
Tangential Edge Angle   
相切边角度
  
Tanto (Tool Position)   
相切(刀具位置
)  
Tap   
攻螺纹
  
Taper Angle   
锥度角
  
T-Cutter  T
形刀
  
Template Set   
模板设置
  
Template units   
模板单位
  
Templates   
模板
  
Temporary Boundary   
临时边界
  
Temporary Plane   
临时平面
  
The Event Generator     
事件生成器
  
The Event Handler     
事件处理器
  
Thick   
厚,粗
   
Thin   
薄,细
  
THREAD     
螺纹  
  
Thread Milling  
螺纹铣
  
Threading Tool  
螺纹车刀
  
Three Point Probe
三点(圆心)探测
  
Thru Fixed Pt  
通过固定点
  
Thru Hole  
通孔
  
Thru point   
通过点
  
Tilt  
倾角
  
Tip Angle   
顶尖角
  
TMARK     
程序转移标识
  
Tolerances   
公差
  
Tolerances – Intol/Outtol 内公差/外公差  

Tolerant Machining   
容错加工  
Tool Axis Output   
刀具轴输出
  
Tool Axis
刀具轴(刀轴)
  
Tool Axis/Distance     
刀具轴/距离
  
Tool Change  
换刀
  
Tool Checker
刀具检测器
  
Tool Diameter  
刀具直径
  
Tool Display   
刀具显示
  
Tool Groups  
刀具组
  
Tool Holder  
刀柄
  
Tool Material   
刀具材料
  
Tool Number   
刀号
  
Tool Objects
刀具对象
  
Tool Path Actions  
刀轨功能
  
Tool Path Options   
刀轨选项
  
Tool path Reversed   
刀轨反向
  
Tool Path
刀位轨迹(刀轨)
  
Tool Position   
刀具位置
  
Tool Preselect  
刀具预选
  
Tool Radius     
刀具半径
  
Tool
刀具
  
toolpath_generate        
刀轨-生成
  
toolpath_list     
刀轨-列表
  
toolpath_reject   
刀轨-拒绝
  
toolpath_replay   
刀轨-重新显示
  
toolpath_verify     
刀轨-验证
  
Top Level   
顶部切削层
  
Topology     
拓扑
  
Total Depth   
总深度
  
Toward Line  
指向线
  
Toward point  
指向点
  
Trace      (
刀轨)迹线
  
Transfer Method   
转移方法
  
Traversal        
横过
  
Traverse Interior Edge  
横过内边缘
  
Traverse Pattern  
横过模式
  
Triangle Tolerance
三角形公差
  
Trim   
修剪
  
Trim Boundary  
修剪边界
  
Trim Curve   
修剪曲线
  
Trim Geometry
修剪几何体
  
Trim Intol   修剪内公差

Trim open boundary   
修剪开口边界
  
Trim Outtol      修剪外公差

Trim Shape   
修剪外形
  
Trim Tool Paths   
修剪刀轨
  
Turn      
车床
  
Turning Tool  
车刀
  
Turning
车削
  
Type  
类型
  
U  
UGPOST   UG
后置处理器
  
Uncut Region Display   
未切削区域显示
  
Uncut Regions
未切削区域
  
Undefined  
未定义
  
Undercut Handing
底部切削处理
  
Unidirection   
单一方向
  
Unify All   
统一所有的材料
  
Unlink Instances     
取消所有引用特征的链接
  
Update All Instances   
更新所有的引用特征
  
Updating Surface   
更新曲面
  
Upper Plane   
上平面
  
Upward     
向上
  
Use Check   
使用检查功能
  
Use Final  
使用最后退刀
  
Use Initial  
使用初始进刀
  
Use Local  
使用局部的进退刀
  
Use Reposition   
使用重新定位
  
Use Tool Holder   
使用刀柄
  
Use Vericut Display   
使用 Vericut模拟切削显示
  
User Abort   
用户中断
  
User Defined  
用户定义
  
User Defined Command      
用户定义命令
  
User Defined Event (UDE)
用户定义事件  


V  
Valley Merge   
凹处合并
  
Valley Overlap   
凹处重叠距离
  
Valleys   
凹处
  
Variable   
可变的
  
Variable Contour  
可变轴曲面轮廓铣
  
Variable Increments   
可变增量
  
Vericut Display   
模拟切削显示
  
Vericut
模拟切削
  
Verify   
验证
  
Verify or modify check surface   
验证或修改检查面
  
Verify Points  
验证点
  
Verify Predrill Points   
验证预钻孔点
  
Vertex Type   
顶点类型
  
Vertical Clearance   
垂直间隙
  
Vertical Limit   
垂直极限
  
Visualize
可视化切削仿真
  
W  
Wall Cleanup  
周壁清理
  
Warning   
警告
  
WCS Origin  WCS
原点
  
WEDM Control     
线切割控制
  
When Gouging  
当过切时
  
White   
白色 
  
Wire EDM  
线切割
  
Wire-EDM Feature        
线切割特征
  
Workpiece  
工件
  
  
X  
X Center R1         R1
中心至刀轴X向距离
  
X Center R2        R2
中心至刀轴X向距离
  
X Delta         X
向增量
  
X Offset         X
向偏置
  
Xaxis        X
 
  
  
Y  
Y Center R1     R1
中心至刀轴Y向距离
  
Y Center R2     R1
中心至刀轴Y向距离
  
Y Delta     Y
向增量
  
Y/Z Offset     Y/Z
向偏置
  
Yaxis    Y
轴 
  
Yellow  
黄色 
  
  
Z  
Z Delta   Z
向增量
  
Z Offset  Z
向偏置
  
Zaxis   Z
  
Z-Depth Offset  Z
向深度偏置
  
Zero  
参考零点
  
Zig with Contour
单向带轮廓铣
  
Zig with Stepover
单向带步距铣
  
Zig
单向切削
  
Zig_Zag Surface  
往复式曲面铣
  
Zig-Zag with Lifts   
往复式切削带抬刀
  
Zig-Zag
往复式切削
  
Z-Level Milling   
等高轮廓铣  

 楼主| 发表于 2007-2-13 23:36:33 | 显示全部楼层

回复: Ug术语中英对照表cam部分

发表于 2010-1-24 15:18:24 | 显示全部楼层

How can I get rid of malware/ spyware?

My computer decided to kick off the end of the year by picking up something that is making it act whacky. My AV (McAfee) is logging and blocking something called winupdate86 from creating files. Now it seems that every 20 minutes there is a pop up that states that Windows will download a anti spyware program. This is the first time that this has happened to me, so I don't know how to handle it. I don't even know if this is spyware, malware, adware or trojan. Even my AV is logging all this it is still does not seem to see this as a problem. So if you could help by answering some questions I would greatly appreciate it. 1. My computer has two hard drives. The AV is logging and blocking files in the first hard drive. Is the second hard drive infected? 2. What free programs are out there to help remove this from my computer? 3. My friend had an executable file that kept trying to log onto the internet. He fixed it by changing the .exe in the file to a .txt. If I know what files are causing the problem can I do the same thing, without harming my computer? 4. Can I take both hard drives, place them in external hard drive enclosures and have a friend with a clean computer scan them to find and remove the problem? 5. Could AVG be downloaded onto a thumb drive and then used to scan my computer? 6. Would it be possible to move files from the second hard drive to an external hard drive without infecting anything? 7. All my friends have Vista or Windows 7. I used Windows XP. If they decided to scan my computer would this cause a conflict with my drives. That is it for now. I am kind paranoid about downloading and installing anything right now. If you can answer all the questions and give me any direction I would greatly appreciate it. Please bear in mind that I am not that very computer saavy. Thanks and have a Happy New Year  forex robot
发表于 2010-5-7 15:53:14 | 显示全部楼层

tramadol and pain relievers comparison

.,
您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|Archiver|小黑屋|几何尺寸与公差论坛

GMT+8, 2024-3-28 17:38 , Processed in 0.059786 second(s), 19 queries .

Powered by Discuz! X3.4 Licensed

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表