PR 254950 Adjustfilter not working as I would design it

huangyhg

Adjustfilter not working as I would design it
<< Bob Hospadaruk  --  05/14/08  16:59:55>>
Open the attached program and go all the way to the bottom.  there you wil find a basic/axis scan taken axially in a bore.  Naturally I want to use the "adjust filter" thingee.  I created two lines, one without and one with this filter, from the scan.  The one without is correctly positioned in X&Y, but the line from the adjust filter is off location for the THEO by a ball radius, and the ACTUAL is off by the diameter.
I have to have this fixed ASAP for a Ford powertrain demo - as you can see the un-adjusted data is no good either and I have to filter this in this way.
<<END>>

<< Jared Hess (Development Notes)  --  04/08/09  22:53:19>>
This has been addedtoreadme for v44 (or ignored if internal item).
<<END>>
<< Changes made by Bob Hospadaruk -- 03/10/09  12:04:56>>
Status:  RESOLVED to CLOSED
<<END>>
<< Troy Johnson  --  02/26/09  10:14:30>>
Reviewed.
<<END>>
<< Changes made by Troy Johnson -- 02/26/09  10:14:46>>
Action:  Troy Johnson to Bob Hospadaruk, Status:  REVIEW to RESOLVED
<<END>>
<< Dan Zwick  --  05/22/08  08:42:46>>
Robert, there was a bug in the new code that caused the crash (see PR 255063). This has been fixed. Could you please try again?
<<END>>
<< Robert Lewenkron  --  05/21/08  14:05:20>>
I tested the program that was supplied with this PR and let Andy R know what I found.
I noticed that after creating a new probe tip for the part program the scanning probe never touched the CAD part. It worked fine with the tip probe file attached to the PR Report but not if a new one was added to the part program. Probe Compensation was on in both locations, one in each of the individual scans and the other in Probing in Parameters box.
Also the PC-DMIS ver 4.3 Program Crashed failed then shut down.
<<END>>
<< Andy Roberts  --  05/19/08  12:38:23>>
I've uploaded a fix for the cylinder.  The uploaded files are:
V431\CONSFEAT\ADJUSTFILTER.CPP
V431\INCLUDE\X_CIR_LN.H
V431\MATHTOOL\X_CIR_LN.CPP
V43B\CONSFEAT\ADJUSTFILTER.CPP
V43B\INCLUDE\X_CIR_LN.H
V43B\MATHTOOL\X_CIR_LN.CPP
V43R\CONSFEAT\ADJUSTFILTER.CPP
V43R\INCLUDE\X_CIR_LN.H
V43R\MATHTOOL\X_CIR_LN.CPP
V44B\CONSFEAT\ADJUSTFILTER.CPP
V44B\INCLUDE\X_CIR_LN.H
V44B\MATHTOOL\X_CIR_LN.CPP
<<END>>
<< Changes made by Andy Roberts -- 05/19/08  12:39:02>>
Action:  Andy Roberts to Troy Johnson, Status:  OPEN to REVIEW
<<END>>
<< Tim Wernicke  --  05/19/08  08:58:46>>
Another report of this in 255029.
<<END>>
<< Andy Roberts  --  05/16/08  16:43:27>>
Dan and I have a solution.  I'm not quite done putting in the code.  I'll finish ASAP.
<<END>>
<< Andy Roberts  --  05/15/08  09:14:35>>
I'm working on a fix for this.  There appears to be two issues.  The first it that in and out are both treated as outer.  The second is that it when the data is filtered the meas vector is discarded, and the theo vector is used for both theo and meas filtered hit values.
<<END>>
<< Changes made by Tim Wernicke -- 05/14/08  16:03:32>>
Action:  Tim Wernicke to Andy Roberts, Assigned:   to Andy Roberts, Priority:  to Stop Rel.
<<END>>