PR 255080 We are not allowed to consdtruct a Gauss filter on a set created fr

huangyhg

We are not allowed to consdtruct a Gauss filter on a set created from an AdjustFilter.
<< Don Ruggieri  --  05/21/08  11:19:05>>
data is in 05212008_01a.zip.  We are not allowed to consdtruct a Gauss filter on a set created from an AdjustFilter.
This tes uses a prototype of the ISO 10360-4 program which has the latest available scan functionalities incorporated.  This is in an effort to plan for the replacement of the older scripting methods used in the original ISO 10360-4 program.
In the original program, after the scan data was collected, it was processed through a BASIC script where the leading and training "extra" points were removed, then the data was spherically adjusted to lie in a common plane.  At that point the data was stored into an empty scan feature for further processing by the program, which had a Gauss filter command prior to final analysis and reporting.
Steps to reproduce:
We open and execute the program which performs the 4 scans.
We use the ScanAdjust / Sphere command to correct the data into the same plane for each scan.
We then try to perform the Gauss filter on the adjusted data.
Results:
There is an error message indicating "Invalid Input.  Must be a scan command."
Expected Results:
I would expect to be able to perform a Gauss filter on a data set created from a scan command.
<<END>>
<< Jared Hess (Development Notes)  --  04/08/09  23:09:14>>
This has been addedtoreadme for v44 (or ignored if internal item).
<<END>>
<< Don Ruggieri  --  06/04/08  15:37:01>>
I've tested this in the V43R,most recently in the 6/3 build, and it is no longer  a problem.  I will close this report.
<<END>>
<< Changes made by Don Ruggieri -- 06/04/08  15:37:04>>
Status:  RESOLVED to CLOSED
<<END>>
<< Dan Zwick  --  05/30/08  10:11:32>>
I uploaded the same files to 4.3R, 4.31, and 4.4B.
<<END>>
<< Changes made by Dan Zwick -- 05/30/08  10:11:36>>
Action:  Dan Zwick to Don Ruggieri, Status:  OPEN to RESOLVED
<<END>>
<< Tim Wernicke  --  05/29/08  16:30:56>>
Hi Dan, please go ahead in V43R, V431 per our Skype.  If you have not uploaded V44B please do so as well.  Thanks.
<<END>>
<< Changes made by Tim Wernicke -- 05/29/08  16:31:04>>
Action:  Don Ruggieri to Dan Zwick, Status:  RESOLVED to OPEN, Priority:  High to Stop Rel.
<<END>>
<< Don Ruggieri  --  05/27/08  12:57:10>>
I installed v43B from 5/24 and re-tested.  This construction option is now allowed.  I am going to continue to test as I did experience some initial problem with it.
<<END>>
<< Dan Zwick  --  05/22/08  13:09:23>>
This has been fixed along with PR 254922. Files uploaded:
V43B\CONSFEAT\FILTEROB.CPP
V43B\BASESCAN\BASICSCN.CPP
I'll upload to 4.4B when I am able to verify the build (debug and release).
<<END>>
<< Changes made by Dan Zwick -- 05/22/08  13:11:13>>
Action:  Dan Zwick to Don Ruggieri, Status:  OPEN to RESOLVED
<<END>>
<< Changes made by Tim Wernicke -- 05/22/08  10:53:31>>
Action:  Andy Roberts to Dan Zwick, Assigned:  Andy Roberts to Dan Zwick
<<END>>
<< Changes made by Bill Wilcox -- 05/21/08  16:54:20>>
Priority:  to High
<<END>>