几何尺寸与公差论坛

 找回密码
 注册
查看: 2213|回复: 0

Published Standards Of Iso/tc 213

[复制链接]
发表于 2009-11-11 22:09:48 | 显示全部楼层 |阅读模式
PUBLISHED STANDARDS OF ISO/TC 213



Updated by 2006-11-05

All standards listed below can only be purchased by contacting the national ISO member body of your country (e.g. JIS in Japan or BSI in the UK or IRAM in Argentina). The ISO Central Secretariat can provide the details of the national memberships.

ISO 1:2002
Geometrical product specifications (GPS) - Standard reference temperature for geometrical product specification and verification


ISO 286-1:1988
ISO system of limits and fits - Part 1: Basis of tolerances, deviations and fits
(under revision together with ISO 1829:1975)


ISO 286-2:1988
ISO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts


ISO 406:1987
Technical drawings - Tolerancing of linear and angular dimensions
(transferred to ISO/TC 213 from ISO/TC 10/SC 1 - under revision)


ISO 463:2006
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges

ISO 1101:2004
Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out


ISO 1101 Extract:1983
Technical drawings - Geometrical tolerancing - Toleranced characteristics and symbols - Examples of indication and interpretation
(under revision)


ISO 1119:1998
Geometrical Product Specifications (GPS) - Series of conical tapers and taper angles


ISO 1302:2002
Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation


ISO 1829:1975
Selection of tolerance zones for general purposes
(under revision together with ISO 286-1:1988)


ISO 1660:1987
Technical drawings - Dimensioning and tolerancing of profiles


ISO/R 1938:1971
ISO system of limits and fits - Part II: Inspection of plain workpieces
(under revision)


ISO 2538:1998
Geometrical Product Specifications (GPS) - Series of angles and slopes on prisms


ISO 2692:1988
Technical drawings - Geometrical tolerancing - Maximum material principle
(under revision)


ISO 2692-AMD1:1992
Technical drawings - Geometrical tolerancing - Maximum material principle - AMENDMENT 1: Least material requirement
(under revision)


ISO 2768-1:1989
General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
(under revision)


ISO 2768-2:1989
General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications
(subject to ISO Systematic Review)


ISO 3040:1990
Technical drawings - Dimensioning and tolerancing - Cones
(subject to ISO Systematic Review)


ISO 3274:1996
Geometrical Product Specifications (GPS) - Surface texture: Profile method - Nominal characteristics of contact stylus instruments
(subject to ISO Systematic Review)


ISO 3274:1996/Technical Corrigendum 1:1998

ISO 3599:1976
Vernier callipers reading to 0,1 and 0,05 mm
(under revision)


ISO 3611:1978
Micrometer callipers for external measurement


ISO 3650:1998
Geometrical product specifications (GPS) - Length standards - Gauge blocks


ISO 4287:1997
Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters
(subject to ISO Systematic Review)


ISO 4287:1997/Technical Corrigendum 1:1998

ISO 4287:1997/Technical Corrigendum 2:2005

ISO 4288:1996
Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture
(subject to ISO Systematic Review)


ISO 4288:1996/Technical Corrigendum 1:1998

ISO 4291:1985
Methods for the assessment of departure from roundness - Measurement of variations in radius
(under revision)


ISO 4292:1985
Methods for the assessment of departure from roundness - Measurement by two-and three-point methods
(subject to ISO Systematic Review)


ISO 5436-1:2000
Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 1: Material measures


ISO 5436-2:2001
Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards


ISO 5458:1998
Geometrical product specifications (GPS) - Geometrical tolerancing - Positional tolerancing


ISO 5459:1981
Technical drawings - Geometrical tolerancing - Datums and datum systems for geometrical tolerances
(under revision)


ISO/TR 5460:1985
Technical drawings - Geometrical tolerancing - Tolerancing of form, orientation, location and run-out - Verification principles and methods - Guidelines


ISO 6906:1984
Vernier callipers reading to 0,02 mm
(under revision)


ISO 7863:1984
Height setting micrometers and riser blocks
(subject to ISO Systematic Review)


ISO 8015:1985
Technical drawings - Fundamental tolerancing principle


ISO 8062:1994
Castings - System of dimensional tolerances and machining allowances
(under revision)


ISO 8512-1:1990
Surface plates - Part 1: Cast iron
(subject to ISO Systematic Review)


ISO 8512-2:1990
Surface plates - Part 2: Granite
(subject to ISO Systematic Review)


ISO 8785:1998
Geometrical Product Specifications (GPS) - Surface imperfections - Terms, definitions and parameters


ISO 10360-1:2000
Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 1: Vocabulary


ISO 10360-1:2000/Technical Corrigendum 1:2002

ISO 10360-2:2001  
Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring size


ISO 10360-3:2000
Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 3: CMMs with the axis of a rotary table as the fourth axis


ISO 10360-4:2000
Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 4: CMMs used in scanning measuring mode


ISO 10360-4:2000/Technical Corrigendum 1:2002

ISO 10360-5:2000
Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 5: CMMs using multiple-stylus probing systems


ISO 10360-6:2001  
Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 6: Estimation of errors in computing Gaussian associated features


ISO 10578:1992
Technical drawings - Tolerancing of orientation and location - Projected tolerance zone
(subject to ISO Systematic Review)


ISO 10579:1993
Technical drawings - Dimensioning and tolerancing - non rigid parts


ISO 11562:1996
Geometrical Product Specifications (GPS) - Surface texture: Profile method - Metrological characteristics of phase correct filters
(subject to ISO Systematic Review)


ISO 11562:1996/Technical Corrigendum 1:1998

ISO 12085:1996
Geometrical Product Specifications (GPS) - Surface texture: Profile method - Motif parameters
(subject to ISO Systematic Review)


ISO 12085:1996/Technical Corrigendum 1:1998

ISO 12179:2000
Geometrical Product Specifications (GPS) - Surface texture: Profile method - Calibration of contact (stylus) instruments


ISO 12179:2000/Technical Corrigendum 1:2003

ISO/TS 12180-1:2003
Geometrical Product Specifications (GPS) — Cylindricity — Part 1: Terms, definitions and parameters of cylindricity


ISO/TS 12180-2:2003
Geometrical Product Specifications (GPS) — Cylindricity — Part 2: Specification operators


ISO/TS 12181-1:2003
Geometrical Product Specifications (GPS) — Roundness — Part 1: Terms, definitions and parameters of roundness


ISO/TS 12181-2:2003
Geometrical Product Specifications (GPS) — Roundness — Part 2: Specification operators


ISO/TS 12780-1:2003Geometrical Product Specifications (GPS) — Straightness — Part 1: Terms, definitions and parameters of straightness

ISO/TS 12780-2:2003
Geometrical Product Specifications (GPS) — Straightness — Part 2: Specification operators


ISO/TS 12781-1:2003
Geometrical Product Specifications (GPS) — Flatness — Part 1: Terms, definitions and parameters of flatness


ISO/TS 12781-2:2003
Geometrical Product Specifications (GPS) — Flatness — Part 2: Specification operators


ISO 13565-1:1996
Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 1: Filtering and general measurement conditions
(subject to ISO Systematic Review)


ISO 13565-1:1996/Technical Corrigendum 1:1998

ISO 13565-2:1996
Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 2: Height Characterization using the linear material ratio curve
(subject to ISO Systematic Review)


ISO 13565-2:1996/Technical Corrigendum 1:1998

ISO 13565-3:1998
Geometrical product specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 3: Height characterization using the material probability curve


ISO 14253-1:1998
Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or non-conformance with specifications


ISO/TS 14253-2:1999
Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification


ISO/TS 14253-3:2002
Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements


ISO/TR 14638:1995
Geometrical Product Specifications (GPS) - Masterplan


ISO 14660-1:1999
Geometrical Product Specifications (GPS) - Geometrical features - Part 1: General terms and definitions


ISO 14660-2:1999
Geometrical Product Specifications (GPS) - Geometrical features - Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature  


ISO 14978:2006
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment


ISO/TS 15530-3:2004
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or standards


ISO/TR 16015:2003
Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurements due to thermal influences  

ISO/TR 16570:2004
Geometrical Product Specifications (GPS) — Linear and angular dimensioning and tolerancing: +/- limit specifications — Step dimensions, distances, angular sizes and radii


ISO/TS 16610-1:2006
Geometrical product specifications (GPS) -- Filtration -- Part 1: Overview and basic concepts

ISO/TS 16610-20:2006
Geometrical product specifications (GPS) -- Filtration -- Part 20: Linear profile filters: Basic concepts

ISO/TS 16610-22:2006
Geometrical product specifications (GPS) -- Filtration -- Part 22: Linear profile filters: Spline filters

ISO/TS 16610-29:2006
Geometrical product specifications (GPS) -- Filtration -- Part 29: Linear profile filters: Spline wavelets

ISO/TS 16610-40:2006
Geometrical product specifications (GPS) -- Filtration -- Part 40: Morphological profile filters: Basic concepts

ISO/TS 16610-41:2006
Geometrical product specifications (GPS) -- Filtration -- Part 41: Morphological profile filters: Disk and horizontal line-segment filters

ISO/TS 16610-49:2006
Geometrical product specifications (GPS) -- Filtration -- Part 49: Morphological profile filters: Scale space techniques


ISO/TS 17450-1:2005
Geometrical Product Specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification


ISO/TS 17450-2:2002
Geometrical Product Specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators and uncertainties


ISO/TS 23165:2006
Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty
http://isotc213.ds.dk/standard.htm
您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|Archiver|小黑屋|几何尺寸与公差论坛

GMT+8, 2024-3-29 05:28 , Processed in 0.046940 second(s), 19 queries .

Powered by Discuz! X3.4 Licensed

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表