【发布】国际标准清单(华中科技大学2005.3.17)

huangyhg

国际标准清单

1、 BS EN 20286-1 ISO system of limits and fits —Part 1: Bases of tolerances, deviations and fits 极限与配合体系——第1部分：公差、偏差与配合的基础

2、BS EN 20286-2 ISO system of limits and fits —Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts 极限与配合体系——第2部分：孔、轴的标准公差等级与极限偏差表

3、BS EN 22768-1 General tolerances —Part 1: Tolerances for linear and angular dimensions without individual tolerance indications 几何公差——第1部分：线性尺寸和角度尺寸的未注公差

4、BS EN 22768-2 General tolerances —Part 2: Geometrical tolerances for features without individual tolerance indications 几何公差——第2部分：几何要素的未注公差

5、BS EN ISO 1 Geometrical Product Specifications (GPS) —Standard reference temperature for geometrical product specification and verification 几何产品技术规范(GPS)——几何产品技术规范与验证的标准参考温度

6、BS EN ISO 11562 Geometric Product Specifications (GPS) —Surface texture: Profile method — Metrological characteristics of phase correct filters 几何产品技术规范(GPS)——表面结构：轮廓法——相位修正滤波器的计量特性

7、BS EN ISO 12085 Geometric Product Specification (GPS) —Surface texture: Profile method —Motif parameters 几何产品技术规范(GPS)——表面结构：轮廓法——Motif 参数

8、BS EN ISO 1302 Geometrical Product Specifications (GPS) -Indication of surface texture in technical product documentation 几何产品技术规范(GPS)——表面结构在产品技术文件中的表示

9、BS EN ISO 13565-1 Geometric Product Specifications (GPS) -Surface texture: Profile method -

Surfaces having stratified functional properties -Part 1: Filtering and general measurement conditions 几何产品技术规范(GPS)——表面结构：轮廓法——

10、BS EN ISO 13565-2 Geometric Product Specifications (GPS) -Surface texture: Profile method -Surfaces having stratified functional properties -Part 2：Height characterization using linear material ratio curve

11、BS EN ISO 13565-3 Geometrical product specifications (GPS) -Surface texture: Profile method; surfaces having stratified functional properties Part 3:Height characterization using the material probability curve

12、BS EN ISO 14253-1 Geometrical Product Specifications (GPS) -Inspection by measurement of workpieces and measuring equipment -Part 1ecision rules for proving conformance or non-conformance with specifications

13、BS EN ISO 14660-1 Geometrical Product Specifications (GPS) -Geometrical features -Part 1： General terms and definitions

14、BS EN ISO 14660-2 Geometrical Product Specifications (GPS) -Geometrical features -Part 2： Extracted median line of a cylinder and a cone， extracted median surface local size of an extracted feature

15、BS EN ISO 10578 Technical drawings -Tolerancing of orientation and location – Projected tolerance zone

16、BS EN ISO 10579 Technical drawings Dimensioning and tolerancing -Non-rigid parts

17、BS EN ISO 1101 Technical drawings –Geometrical tolerancing - Tolerancing of form, orientation, location and run-out -Generalities, definitions, symbols, indications on drawings

18、BS EN ISO 2692 Technical drawings –Geometrical tolerancing -Maximum material principle (including Amendment l:1992 Least material requirement)

19、BS EN ISO 3040 Technical drawings -Dimensioning and tolerancing - Cones

20、BS EN ISO 406 Technical drawings -Tolerancing of linear and angular dimensions

21、BS EN ISO 5459 Technical drawings – Geometrical tolerancing – Datums and datum-systems for geometrical tolerances

22、BS EN ISO 8015 Technical drawings –Fundamental tolerancing principle

23、DD ENV ISO 14253-2 Geometrical Product Specifications (GPS) -Inspection by measurement of workpieces and measuring equipments -Part 2, Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification

24、BS EN ISO 1660 Technical drawings -Dimensioning and tolerancing of profiles

25、BS EN ISO 3274 Geometric Product Specifications (GPS) -Surface texture: Profile method -Nominal characteristics of contact (stylus) instruments -

26、BS EN ISO 4287 Geometrical product specification (GPS) -Surface texture: Profile method - Terms, definitions and surface texture parameters

27、BS EN ISO 4288 Geometric Product Specification (GPS) -Surface texture -Profile method: Rules and procedures for the assessment of surface texture

28、BS EN ISO 5458 Geometrical Product Specifications (GPS) –Geometrical tolerancing -Positional tolerancing

29、BS EN ISO 8785 Geometrical Product Specification (GPS) –Surface imperfections -Terms, definitions and parameters