Published Standards Of Iso/tc 213
PUBLISHED STANDARDS OF ISO/TC 213
Updated by 2006-11-05 All standards listed below can only be purchased by contacting the national ISO member body of your country (e.g. JIS in Japan or BSI in the UK or IRAM in Argentina). The ISO Central Secretariat can provide the details of the national memberships. ISO 1:2002 Geometrical product specifications (GPS) - Standard reference temperature for geometrical product specification and verification ISO 286-1:1988 ISO system of limits and fits - Part 1: Basis of tolerances, deviations and fits (under revision together with ISO 1829:1975) ISO 286-2:1988 ISO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 406:1987 Technical drawings - Tolerancing of linear and angular dimensions (transferred to ISO/TC 213 from ISO/TC 10/SC 1 - under revision) ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges ISO 1101:2004 Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out ISO 1101 Extract:1983 Technical drawings - Geometrical tolerancing - Toleranced characteristics and symbols - Examples of indication and interpretation (under revision) ISO 1119:1998 Geometrical Product Specifications (GPS) - Series of conical tapers and taper angles ISO 1302:2002 Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation ISO 1829:1975 Selection of tolerance zones for general purposes (under revision together with ISO 286-1:1988) ISO 1660:1987 Technical drawings - Dimensioning and tolerancing of profiles ISO/R 1938:1971 ISO system of limits and fits - Part II: Inspection of plain workpieces (under revision) ISO 2538:1998 Geometrical Product Specifications (GPS) - Series of angles and slopes on prisms ISO 2692:1988 Technical drawings - Geometrical tolerancing - Maximum material principle (under revision) ISO 2692-AMD1:1992 Technical drawings - Geometrical tolerancing - Maximum material principle - AMENDMENT 1: Least material requirement (under revision) ISO 2768-1:1989 General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (under revision) ISO 2768-2:1989 General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (subject to ISO Systematic Review) ISO 3040:1990 Technical drawings - Dimensioning and tolerancing - Cones (subject to ISO Systematic Review) ISO 3274:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Nominal characteristics of contact stylus instruments (subject to ISO Systematic Review) ISO 3274:1996/Technical Corrigendum 1:1998 ISO 3599:1976 Vernier callipers reading to 0,1 and 0,05 mm (under revision) ISO 3611:1978 Micrometer callipers for external measurement ISO 3650:1998 Geometrical product specifications (GPS) - Length standards - Gauge blocks ISO 4287:1997 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters (subject to ISO Systematic Review) ISO 4287:1997/Technical Corrigendum 1:1998 ISO 4287:1997/Technical Corrigendum 2:2005 ISO 4288:1996 Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (subject to ISO Systematic Review) ISO 4288:1996/Technical Corrigendum 1:1998 ISO 4291:1985 Methods for the assessment of departure from roundness - Measurement of variations in radius (under revision) ISO 4292:1985 Methods for the assessment of departure from roundness - Measurement by two-and three-point methods (subject to ISO Systematic Review) ISO 5436-1:2000 Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 1: Material measures ISO 5436-2:2001 Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards ISO 5458:1998 Geometrical product specifications (GPS) - Geometrical tolerancing - Positional tolerancing ISO 5459:1981 Technical drawings - Geometrical tolerancing - Datums and datum systems for geometrical tolerances (under revision) ISO/TR 5460:1985 Technical drawings - Geometrical tolerancing - Tolerancing of form, orientation, location and run-out - Verification principles and methods - Guidelines ISO 6906:1984 Vernier callipers reading to 0,02 mm (under revision) ISO 7863:1984 Height setting micrometers and riser blocks (subject to ISO Systematic Review) ISO 8015:1985 Technical drawings - Fundamental tolerancing principle ISO 8062:1994 Castings - System of dimensional tolerances and machining allowances (under revision) ISO 8512-1:1990 Surface plates - Part 1: Cast iron (subject to ISO Systematic Review) ISO 8512-2:1990 Surface plates - Part 2: Granite (subject to ISO Systematic Review) ISO 8785:1998 Geometrical Product Specifications (GPS) - Surface imperfections - Terms, definitions and parameters ISO 10360-1:2000 Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 1: Vocabulary ISO 10360-1:2000/Technical Corrigendum 1:2002 ISO 10360-2:2001 Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring size ISO 10360-3:2000 Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 3: CMMs with the axis of a rotary table as the fourth axis ISO 10360-4:2000 Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 4: CMMs used in scanning measuring mode ISO 10360-4:2000/Technical Corrigendum 1:2002 ISO 10360-5:2000 Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 5: CMMs using multiple-stylus probing systems ISO 10360-6:2001 Geometrical Product Specifications (GPS) - Acceptance and reverification test for coordinate measuring machines (CMM) - Part 6: Estimation of errors in computing Gaussian associated features ISO 10578:1992 Technical drawings - Tolerancing of orientation and location - Projected tolerance zone (subject to ISO Systematic Review) ISO 10579:1993 Technical drawings - Dimensioning and tolerancing - non rigid parts ISO 11562:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Metrological characteristics of phase correct filters (subject to ISO Systematic Review) ISO 11562:1996/Technical Corrigendum 1:1998 ISO 12085:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Motif parameters (subject to ISO Systematic Review) ISO 12085:1996/Technical Corrigendum 1:1998 ISO 12179:2000 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Calibration of contact (stylus) instruments ISO 12179:2000/Technical Corrigendum 1:2003 ISO/TS 12180-1:2003 Geometrical Product Specifications (GPS) — Cylindricity — Part 1: Terms, definitions and parameters of cylindricity ISO/TS 12180-2:2003 Geometrical Product Specifications (GPS) — Cylindricity — Part 2: Specification operators ISO/TS 12181-1:2003 Geometrical Product Specifications (GPS) — Roundness — Part 1: Terms, definitions and parameters of roundness ISO/TS 12181-2:2003 Geometrical Product Specifications (GPS) — Roundness — Part 2: Specification operators ISO/TS 12780-1:2003Geometrical Product Specifications (GPS) — Straightness — Part 1: Terms, definitions and parameters of straightness ISO/TS 12780-2:2003 Geometrical Product Specifications (GPS) — Straightness — Part 2: Specification operators ISO/TS 12781-1:2003 Geometrical Product Specifications (GPS) — Flatness — Part 1: Terms, definitions and parameters of flatness ISO/TS 12781-2:2003 Geometrical Product Specifications (GPS) — Flatness — Part 2: Specification operators ISO 13565-1:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 1: Filtering and general measurement conditions (subject to ISO Systematic Review) ISO 13565-1:1996/Technical Corrigendum 1:1998 ISO 13565-2:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 2: Height Characterization using the linear material ratio curve (subject to ISO Systematic Review) ISO 13565-2:1996/Technical Corrigendum 1:1998 ISO 13565-3:1998 Geometrical product specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 3: Height characterization using the material probability curve ISO 14253-1:1998 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or non-conformance with specifications ISO/TS 14253-2:1999 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification ISO/TS 14253-3:2002 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements ISO/TR 14638:1995 Geometrical Product Specifications (GPS) - Masterplan ISO 14660-1:1999 Geometrical Product Specifications (GPS) - Geometrical features - Part 1: General terms and definitions ISO 14660-2:1999 Geometrical Product Specifications (GPS) - Geometrical features - Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature ISO 14978:2006 Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment ISO/TS 15530-3:2004 Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or standards ISO/TR 16015:2003 Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurements due to thermal influences ISO/TR 16570:2004 Geometrical Product Specifications (GPS) — Linear and angular dimensioning and tolerancing: +/- limit specifications — Step dimensions, distances, angular sizes and radii ISO/TS 16610-1:2006 Geometrical product specifications (GPS) -- Filtration -- Part 1: Overview and basic concepts ISO/TS 16610-20:2006 Geometrical product specifications (GPS) -- Filtration -- Part 20: Linear profile filters: Basic concepts ISO/TS 16610-22:2006 Geometrical product specifications (GPS) -- Filtration -- Part 22: Linear profile filters: Spline filters ISO/TS 16610-29:2006 Geometrical product specifications (GPS) -- Filtration -- Part 29: Linear profile filters: Spline wavelets ISO/TS 16610-40:2006 Geometrical product specifications (GPS) -- Filtration -- Part 40: Morphological profile filters: Basic concepts ISO/TS 16610-41:2006 Geometrical product specifications (GPS) -- Filtration -- Part 41: Morphological profile filters: Disk and horizontal line-segment filters ISO/TS 16610-49:2006 Geometrical product specifications (GPS) -- Filtration -- Part 49: Morphological profile filters: Scale space techniques ISO/TS 17450-1:2005 Geometrical Product Specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification ISO/TS 17450-2:2002 Geometrical Product Specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators and uncertainties ISO/TS 23165:2006 Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty http://isotc213.ds.dk/standard.htm |
所有的时间均为北京时间。 现在的时间是 06:02 PM. |