几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CMM检测 » PC-DMIS
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


回复
 
主题工具 搜索本主题 显示模式
旧 2007-11-14, 03:23 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 Iterative Alignment Rules

Iterative Alignment Rules

There are some general rules when doing an iterative alignment :

PC-DMIS needs both the measured values and theoretical values for each of the elements in the sets. The normal vectors for the first set of elements must be approximately parallel. The one exception to this rule is if only three features are being used in the set.

If measured points (VECTOR, EDGE, or SURFACE) are being used, then all three sets of elements are needed (three features to Level, two features to Rotate, and one feature to Set Origin) to define the alignment. Any feature type can be used, but three-dimensional elements are better defined elements and therefore improve the accuracy. Some of the possible 3D elements are sheet metal circle, slot, cylinder, sphere, or a corner point.

Note: The sheet metal circle, slot, and cylinder need at least three sample hits.


The difficulty of using measured points lies in not knowing where to take the measurement until after the alignment. This poses a problem as the points must be measured before the alignment. Three dimensional elements, by definition for this use, are elements that can be measured precisely the first time.

Further, if measured points (VECTORS, EDGE, or SURFACE) are being used, the normal vectors of the features in the ROTATE set must have normal vectors that are approximately perpendicular to the vectors of the features in the LEVEL set. The features in the ORIGIN set must have a normal vector that is approximately perpendicular to both the vectors from the LEVEL set and the ROTATE set.

If measured points (VECTORS, EDGE or SURFACE) are being used as part of the set, PC-DMIS may ask that they be re-measured if they were taken too far from the nominal location. PC-DMIS first "best fits" the measured data to the nominal data. Next, PC-DMIS checks to see how far off each measured point is. If the distance is greater than the amount specified in the Point Target Radius box, PC-DMIS will request that the point be re-measured. PC-DMIS in effect puts a cylindrical tolerance zone around the theoretical location of each vector, surface, or edge point. The radius of this tolerance zone is the point tolerance specified in the dialog. PC-DMIS will continue to re-measure point features until all the measured points fall into 'tolerance'. The tolerance zone only affects measured points.

A special capability of PC-DMIS allows the center point of a slot to slide up or down the axis as needed. For this reason, an iterative alignment cannot converge when a slot is used as part of the ORIGIN set. It is possible to use a slot as part of the ORIGIN set by first constructing a point from the slot and then using that constructed point in the ORIGIN set.

A slot is not recommended as part of the ORIGIN set of an iterative alignment.


Type of Feature used:

Minimum # of Features needed:

Circle

3 circles:

This method uses 3 DCC circles for the alignment.

Line

This feature type is not recommended.

Point

6 points:

The points are used as a 3-2-1 alignment.

Slot

This feature type is not recommended as part of the ORIGIN set.

Sphere

3 spheres:

This method uses 3 set spheres for the alignment.
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
回复


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
【发布】测量点集曲面重建若干关键技术与研究:提交版-黄运保博士学位论文.pdf huangyhg 期刊论文交流 1 2005-04-06 02:34 PM


所有的时间均为北京时间。 现在的时间是 05:44 PM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多