几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


 
 
主题工具 搜索本主题 显示模式
旧 2009-09-07, 11:54 AM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 anchor bolts...do i need them

anchor bolts...do i need them.
hey;
is it stated any where in a code that a structure must be anchored down, specifically, anchored with anchor bolts to a foundation? i have a small shack (40ft long x 12ft wide x 12ft high, approximatly 41,000 lbs heavy.). do i need to anchor it to the foundation per any codes in canada even if wind loads cannot move it. there will be no issue for uplift since wind can not get underneath the shack.
thanks,
m.
what stops it sliding horizontally
how do they erect the columns with no anchor bolts?
it can still tip over. it is like pushing a box, you can still have upflift when it rotates.
never, but never question engineer's judgement
wind doesn't have to get underneath to lift. suction can do the job. but if your "shack" truly weighs 41000 pounds, that is about 85 psf, so it shouldn't blow away.
jmho:
why would you want to be the guy who goes out on the limb? a few well place anchor bolts would be of neglible cost, and would provide a lot of piece of mind.
also, keep in mind, if there is a problem, it might be hard to prove that you followed a 'standard of care' consistant with what other engineers would do, as i believe most engineers would put in some anchor bolts.
jmho.
not being an american, but what about osha? iirc, there was a requirement about 4 bolts and a minimal load on top.
mike
i agree with the others.
why take the risk?
mark,
note that i am not "the others". if your structure is as heavy as you say it is, it doesn't need to be anchored.
are you a structural engineer?
ucfse,
to whom is your question directed?
mark, the op.
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
 


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭



所有的时间均为北京时间。 现在的时间是 10:15 PM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多