几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


 
 
主题工具 搜索本主题 显示模式
旧 2009-09-07, 01:13 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 asce 7-05 wind diagrams

asce 7-05 wind diagrams
it is a low rise building
main wind force resisting system consist of columns, vxb on outside grid in both directions and roof horizontal bracing.
the roof is made up of trusses and at the bottom chord level is the horizontal bracing acting as diaphragm.
there is "no moment connections" anywhere. the whole building is modeled in 3-d using s-frame.
i am using fig-6-10 of asce 7-05 only for getting force/reactions in vxb, roof horizontal bracing and columns at vxb locations.
i am confused between figure 6-10(mwfrs) and 6-11a(walls) & 6-11b(roof) as to which one to use for inputing in my 3-d model to get column and truss design forces for various load combinations.
my concerns are :
1. do we use fig 6-10 only when we have "rigid frame" type structure or can it be used for other cases also without rigid frames for modeling in 3-d.
2. the columns and truss has to be designed for forces based on individual tributary area based on coeff. from fig 6-11.
if i need to use these values, then for the columns it gives me max coeff. values(press. or suction) for one face only. how do i enter in my model for both windward and leeward faces?
am i thinking correctly or am i missing something?
any clarification will be of great help.
thanks,
the wind doesnt care if it is a braced frame or a rigid frame - the basic values are the same.
the only difference is in the relative areas that are supported by each element.

lokstr,
figure 6-10 is for the main wind force resisting system (mwfrs) and figure 6-11a to d are for components & clading (c&c). check section 6.2, definations and commentary chapter c6.2 for clarification.
you might check section 6.4, method 1-simplified procedure to see if your structure fits the conditions that let you use figure 6-2.
okstr,
you use fig. 6-10 to calculate loads to input into your model, and then analyze it to get column loads (both uplift and compressive.) it doesn't matter if you have moment frames or not.
you do not have to design the truss and columns for the forces based on trib areas and coefficients from fig 6-11. that may seem counterintuitive. the pressures you get on the wall & roof panels, girts & purlins, and all of their connections when using fig 6-11 are higher than those you get when using fig 6-10. this is so because when designing the panels, girts & connections, you are accounting for maximum pressures that can occur on these components, at any point in time. when yiou design the trusses and coumns, you take advantage of the fact that these maxima don't occur at all points at the same time: at a specific point in time, some locattions experience that max pressure, while many others do not. that's why the mwfrs coefficients & pressures are smaller than the components and cladding values.
does this make sense?
regards,
chichuck
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
 


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
asce 7-05 wind design inten huangyhg 产品功能分析 0 2009-09-07 01:13 PM
asce 7-02 wind load enclosure type opinion huangyhg 产品功能分析 0 2009-09-07 01:04 PM
asce 7 wind torsion loads huangyhg 产品功能分析 0 2009-09-07 01:00 PM
asce 37-02 construction wind loads huangyhg 产品功能分析 0 2009-09-07 12:55 PM
are asce 7-02 wind loads ultimate or service level huangyhg 产品功能分析 0 2009-09-07 12:46 PM


所有的时间均为北京时间。 现在的时间是 05:53 AM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多