几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 - What is the range of tolerance value for Modeler::SetToleranceValue?

		几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)\|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 仿射空间：CAX软件开发（三）二次开发与程序设计 » CAD二次开发 » SolidWorks二次开发
What is the range of tolerance value for Modeler::SetToleranceValue?

标记论坛为已读

搜索本主题

上一页

上一帖

下一帖

2006-12-19, 12:59 PM	#1
directdwg 初级会员注册日期: 06-12 帖子: 5 精华: 0 现金: 22 标准币资产: 22 标准币	What is the range of tolerance value for Modeler::SetToleranceValue? Q: What is the range of tolerance value for Modeler::SetToleranceValue? And what is the default or optimized value of tolerance in SW modeler? What is the value range for ModelDoc2.SetTessationQuality? And what is the default or optimized value for tessellation of OPENGL? R: For SetTolerance below is information about the default values. I don’t think there is a range. For SetTessationQuality the range is 0-100, the default is 46. The default tolerance setting for 3D geometry output is 0.01 meters, while 2D geometry uses a 1e-4 dimensionless tolerance value. If your 3D trim curves are coming out too far from the surfaces they are trimming or are not close to the 2D trim curves, then you might want to tighten the tolerance. Set the tolerances before any extraction of geometry. The tolerance values can be reset by other AddIns such as IGES. Make sure that they are set to your values when you need them. The tolerance settings only affect other AddIn applications. However, you should be careful to reset the tolerances so that other AddIn applications are not affected by your choice of tolerance. The swUVCurveOutputTol tolerance is used during the extraction of UV (SP) trim curves. The Face2::GetTrimCurves2 method is affected by this setting. This tolerance value represents a fraction of the characteristic small dimension of a face (the tolerance is dimensionless). For example, if you set the swUVCurveOutputTol tolerance value to 3e-6 and the smallest dimension of the face is 0.4 meters, then the largest deviation of the trim curve will be: (0.4 x 3e-6) meters For reference, the SolidWorks IGES processor lets you control the swUVCurveOutputTol tolerance setting in the user preferences area. The normal setting under IGES uses a tolerance of 1e-4, while the high setting changes this tolerance to 3e-6. The IGES setting does not affect your application. Higher tolerance settings can increase processing time and the size of any output results. Robin Richter

GDT自动化论坛（仅游客可见）

« 上一主题 | 下一主题 »

主题工具	搜索本主题
显示可打印版本发送本页给好友	搜索本主题: 高级搜索
显示模式
切换到平板模式切换到混合模式树形模式

发帖规则
您不可以发表新主题您不可以回复主题您不可以上传附件您不可以编辑您的帖子 vB 代码开启表情图标开启 [IMG]代码开启 HTML代码关闭

相似的主题
主题	主题发起者	论坛	回复	最后发表
using profile of a surface tolerance on size controls the form better	huangyhg	tec-ease(America)	2	2007-10-28 04:55 PM
How to set the tolerance parameters of Tessellate face?	huangyhg	SolidWorks二次开发	1	2006-12-11 12:43 PM

所有的时间均为北京时间。现在的时间是 08:33 PM.

沪ICP备06057009号-2

更多